Sears offers two different drive mechanisms to accommodate your home and budget. If you're looking for a smooth and quiet opener for a garage door with rooms located above the garage or attached to the garage, the belt drive is going to be the best for you. You can also choose a chain drive opener, which is perfect for garages that are unattached to the home.
Since most yards entertain play activity including baseballs and other sporting equipment, it's no surprise that garage doors experience broken glass from time to time. Regardless of the cause, it's important to repair glass quickly, since broken glass in a garage is a safety issue, a security problem, and an invitation to every bird and insect in the neighborhood to take up residence in your garage. Fortunately, it's not difficult to replace a pane of glass. The techniques are exactly the same as for replacing glazing in a house window.
4. It is also important to note that extension springs sometimes do not break but rather ‘stretch out’. This is easy to spot as the space between coils when the door is closed is normally consistent. When the spring fails without breaking the space between the coils will become very inconsistent. This condition is quite visible and if it exists the springs should be replaced (Know when to call quits with your garage door). 

Action Garage Door Repair Centennial Colorado 80016


If you have two torsion springs on your garage door, the good spring will most likely keep the cables on the drums when the other spring breaks. This makes it much easier to lift because the good spring will be pulling half the weight of the garage door. You can also use the garage door opener to help assist while someone lifts the door and acts as the broken spring. Use extreme caution when doing this to prevent damage to your garage door or injury to a person.

Garage Door Repair And Installation Centennial Co


There could be a few issues that might be causing your transmitters not to work properly. The most common reason could be that you’re simply out of range of your garage door. Each garage door and transmitter combo has a specific range it will function in. If you’re trying to open your garage door before you can even see your house, then chances are you’re just too far away. Try waiting until you turn into your driveway to hit your transmitter button, and you should have more success opening your garage door on the first try.

A spring replacement is one of the most common repairs required on a garage door. These springs come in varying sizes and act as a balance, lifting over 90% of the garage door weight. This allows the door to easily open and close manually or with the assistance of an opener. Discount Garage Door's replacement springs ensure a longer life expectancy for the entire garage door system.

6.10 If the garage door comes off the floor when you pull down on the bar, and if the cone still won't loosen, tap the bar next to the cone with a hammer to force the cone beyond the swollen portion of shaft. Maintain a firm grip on the bar; keep it firmly inserted completely into the cone; and be prepared at all times for the cone to slip, break, explode or break free from the shaft and yank the bar down.

Garage Door Repair How Much Centennial Colorado 80015


A garage door with a broken torsion spring can fall rapidly and cause injury or death. However, the most common danger comes when your torsion springs break and you decide to undertake the repair/replace them yourself. Torsion springs can be very dangerous, and you not only need the exact tools for the job, but also need to have a good knowledge of the mechanics involved. Some of the parts involved in such a process can be life threatening, and must be handled with care and precision, which is why it is always recommended that you call in a professional, rather than trying to handle a replacement or repair by yourself. Failure to do so may leave you with injuries and/or damage to your property.

Garage Door Repair Average Cost Centennial Co


Oklahoma City, Edmond, Norman, Moore, Tulsa, Broken Arrow, Owasso, Claremore, Central Oklahoma, Sapulpa, New Tulsa, Jenks, Glenpool, Prattville, Sand Springs, Leonard, Coweta, Kiefer, Oakhurst, Inola, Fair Oaks, Verdigris, Lotsee, Sperry, Justice, Valley Park, Bixby, Mannford, Cleveland, Westport, Prue, Bethany, Yukon, Midwest City, Spencer, Newcastle, Harrah, Jones, Piedmont, Arcadia, Luther, Wellston, Dell City, Tuttle, Bridge Creek, Blanchard, Mustang, Noble, Goldsby


The two main garage door operating mechanisms are sectional roll-ups or tilt-ups. Garage door repair services can fix single-car, double-car or RV-height doors. Your garage door may be made of wood, steel, aluminum, masonite, vinyl, fiberglass or another material. The type of garage door repair you need really depends on the type of garage door you have and the issue at hand. Garage door repair pros often charge a flat service call fee to diagnose the problem and provide an estimate. For customers who choose to have the repair done, the service call fee may be applied to the first hour of labor (including time to make the diagnosis). If your garage door is under warranty, the repair may be free of charge. https://www.youtube.com/v/Z_eZc-kh40c?version=3

In need of garage door repair? Contact one of our many well-trained garage door repair professionals today to provide your garage door system with the recommended service and maintenance procedures for smooth and reliable operation. Our garage door repair professionals are here for you, whether you want to fix your existing garage door or buy a new garage door. Are you looking to replace a garage door spring, cable or roller or searching for 'garage door repair near me'? Use our distributor locator below: 
If your photo eyes are clean and the door still isn’t closing, the next thing you’ll need to do is check the alignment of the eyes. The eyes should be pointing in exactly the same direction and at the same angle. If they’re off, they won’t register that the other one is there, and it’ll assume something is in its path, causing the door to stay in the open position. When checking the alignment, measure the height of each photo eye from the ground. Use a level to make sure they’re pointing directly across at each other at the same angle. A laser level will make this part a little easier, but if you don’t have one, a regular level will work as well. https://www.youtube.com/embed/Z_eZc-kh40c
If one of your door springs just broke and you are looking for instructions to decide if you can change the spring or springs safely and correctly, this page should help. DO NOT OPEN AND CLOSE YOUR GARAGE DOOR. Wooden garage doors are heavy and will probably damage or ruin the opener. The tops of steel doors often bend when operated with broken springs.
Not only was the upward-lifting garage door and the electric garage door opener invented by Overhead Door Corporation’s founder C.G Johnson in the 1920s, but we also have a tradition in excellence for garage door repair, service and maintenance. Even with the most reliable products problems can arise and when they do it’s important to know who to contact to fix these issues while providing solutions to prevent future complications.

To evaluate whether the problem lies with the door or the automatic opener, make sure the door is in the fully closed position, then disengage the opener trolly from the door by pulling the emergency release cord. Try to lift the garage door by hand. If the door opens smoothly by hand, the problem is with the opener. If the garage door still only opens halfway, the problem is with the door.


Roller doors ("Sheet Doors"-USA) are usually constructed of corrugated steel. They evolved from cover window and door coverings.[4] Other materials can be used (e.g.; transparent corrugated fibreglass) where strong impact resistance is not required. Corrugations give the door strength against impacts. A typical single car garage roller door has a preloaded spring inside the rolling mechanism. The spring reduces the effort required to open the door. Larger roller doors in commercial premises are not sprung (except USA) and use a manual pulley and chain system or a geared motor to raise and lower (roll up and roll down) the door. Roller doors cannot be effectively insulated.
Install the center bearing and the right spring, then secure the cones. Slide the torsion bar to the left then add the center bearing. Slide the right spring onto the bar and press the bearing into the stationary cone. Connect both of the stationary cones to the center bracket with the nuts and bolts you removed previously. Remove the locking pliers or clamp from the center bracket.[10]

Since garage doors come in all weights and sizes, the right springs need to be installed in order to properly balance the door. If a technician puts the wrong spring on your door, not only will this damage your garage door system, but it will cause the garage door opener to do more work than it was built to do. This is why Precision technicians only install the right springs for the door's weight and check their work by performing a balance test.
NEVER use screwdrivers, pin punches or pliers handles to wind or unwind a torsion spring. Trust us: This is the best way to wind up in the hospital. Don't even think about doing this job without a proper set of winding bars. You can buy a set of professional hardened-steel winding bars for about $25 from online suppliers. (Garagedoorpartsusa.com and stardoorparts.com are two online sources that sell winding bars, springs and other parts.) Professional winding bars work with 1/2-in. and 7/16-in. winding cones. If your winding cones have 1/2-in. openings, you can make your own winding bars by cutting a 36-in. length of 1/2-in.-diameter round bar stock in half (buy round bar stock from any hardware or home center). Just file a smooth bevel on each end so it slides into the winding cone holes easier.
Homeowners have long been warned that torsion springs are extremely dangerous to work with and that replacing them must be left to a professional. But these claims are somewhat exaggerated. If you understand how they work, and you pay attention to what you're doing, you can replace them safely and surprisingly easily. Granted, they're a little spooky to work with at first (partly due to their reputation), but this is a good thing—you really don't want to forget that they're under tension. Thinking about every step — before you take it — is the key to staying safe.
Torsion springs are located above the opening of your door with springs that slide onto a bar. Extension spring systems can be found alongside the opening of the door. It's important to know whether or not a garage door company provides service for your needs. Precision's professionally trained technicians are fully equipped to work on torsion and extension spring systems.

Garage Door Repair And Service Centennial Colorado 80015


11.2a Raise the garage door slowly. Check the door balance. If you have the correct springs the door should stay down when closed, half way when opened half way, and open when opened. If the door will drop to the floor by itself from the halfway point, add 1/4 turn of tension to each of the torsion springs. If the garage door won't stay on the floor, and if it pulls itself up when stopped halfway, close the door and remove 1/4 turn of tension from the springs.
Maybe the battery died or a spring broke, but you can't get into the garage to even see what the problem is. If the garage door is the only way in or out, or if you can't find the key to the door, you'll have to either find a way to break in or call a locksmith. As a preventative measure, it's smart to keep a spare key or install an emergency key release that would allow you to release the emergency disconnect to the operator so you can manually raise the door.

These instructions are for doors with cable drums and cables that look similar to those in the picture below. The next part beyond the end of the spring assembly is the cable drum. The drum is cast aluminum alloy 4" in diameter and 12.6" in circumference around the flat portion. Just beyond the cable drum is the end bearing plate. The cable unwraps off the back of the drum between the drum and the garage wall or jamb and travels down alongside the door, inside the track brackets and behind the roller stems as shown.
Clean the photoelectric safety eyes at the bottom of the door track with a clean rag if the opener did not operate with the push button. Sometimes dirt and moisture will keep the eyes from making a good connection. Push the wall button again to see if the opener operates. If the opener does not operate, call a door professional to troubleshoot your door opener. Meanwhile, you can still open and close your door manually.
For commercial or residential doors, operators and accessories outside of the U.S. or Canada you can contact international. ​​​​​​Please be sure to include the following in your e-mail, so we can connect you with the Overhead Door™ Distributor that can best serve you: Contact Person, Phone Number (including local dialing code), Company Name, City and Country, Product(s) of interest (i.e. residential or commercial garage doors, operators and accessories), Name of Project (if any) and Project Specifications.​​​​​​​​​​​​ 

Automatic Garage Door Repair Centennial Colorado 80015


Single panel doors are constructed from one monolithic panel. From the closed position a single panel door swings up and overhead with a hinge on each side (known as jamb type hardware) to the fully open position. A disadvantage of monolithic panel doors is that the swing up arc of the door occurs partially outside the garage. This means a vehicle must stop and park several feet in front of the door to avoid being hit by the garage door when it is opened.
4. It is also important to note that extension springs sometimes do not break but rather ‘stretch out’. This is easy to spot as the space between coils when the door is closed is normally consistent. When the spring fails without breaking the space between the coils will become very inconsistent. This condition is quite visible and if it exists the springs should be replaced (Know when to call quits with your garage door). 

Garage Door Repair Estimates Centennial Colorado 80016


Lewis did a great job and not only met my expectations but blew them away. His attention to detail was impressive. He reolaced the springs on my two car garage door and he went out of his way to adjust the tension on my second single car garage door to make it open better. He also recommended replacement of the rollers on my main garage door as they were getting pretty worn out and making some noise. He was very friendly and personable. Was willing to explain what he was doing so we could learn something too. I would recommend Lewis Nagy if you are in his area here in Apollo Beach/Riverview. Thanks again! 

Garage Door Repair Companies Centennial Co 80015


While it would be wonderful if door springs lasted forever, the reality is that the simple act of opening and shutting the door multiple times every day isn’t easy. It’s hard on the springs, even though they’re built to do it. Most springs will last for a while, but they won’t last forever. The regular wear and tear of endlessly opening and shutting the door breaks them down and eventually, they’ll need to be replaced.
2.4 The same is true of Older Overhead, BarCol and Raynor torsion springs that have winding cones with inconsistent hole sizes. If you insert a 1/2" X 18" bar in some of these holes you can move the opposite end of the bar over four inches. Bars in newer cones move less than 1 1/2". I've had many of the older cones spin loose from my bars, the last one generating an $1800 emergency room bill. If your cones are like any of these, or if they have more than 2" of play, leave the job of installing torsion springs to a professional garage door mechanic.
Replacing a garage door panel can add significantly to the cost of a garage door repair. Panels run horizontally on sectional roll-up garage doors. They may be made of wood, vinyl, aluminum, fiberglass or steel. Garage door panels can become damaged from hail and other extreme weather, dents and dings, car accidents, and age. When deciding if you want to replace a garage door panel, it’s helpful to compare the potential repair cost to the cost of a new garage door. Panel replacement requires a pro with the proper tools as well as the new parts. With parts and labor you could be paying more than $500 for one new panel. In comparison, a new garage door may cost $800-$1,200 (on average) with installation. If there is a possibility your garage door was structurally compromised when the panel was damaged, have the pro assess whether it’s better to completely remove and replace the door, rails and framework to ensure your home’s safety. It may also be better to completely replace your door if it is severely rusted or dented; if the paint is peeling and fading; if the door model is outdated or you can’t find replacement panels; or if the panels or rails are structurally compromised.
Quite a few garage doors come with manual locks, especially older models, for added security for your house. These typically look like a knob or handle in the middle of your door with two bars running horizontally from each side. There may be a small button on the top or side of the handle that you can press to slide the bars across the doors, thus locking the garage door from the inside. It can be somewhat easy to accidentally hit that button, especially if you’re getting large objects out of the trunk of your car near the door.
10.4 Raise the second bar 90 degrees and insert the first bar. This is "three." Continue winding. If the spring shortens in length, unwind the spring and switch sides - the springs are on backward. Otherwise, continue winding until you reach a count of "30." This is 7 1/2 turns, which is normal for most 7' doors. Longer life springs are wound the same number of turns. Newer steel doors with only one strut on top often need only 7 1/4 turns. On 8' doors count to 34. Each time you insert a bar into the winding cone, listen for the click to let you know the bar is in all the way. Not inserting the bar all the way could cause the cone to explode.
Annual maintenance. Make an annual check of all nuts and bolts on rails and rollers to make sure they’re firmly tightened. Check the condition of all cables to make sure they’re not worn or frayed. Lubricate rollers and springs with a garage-door lubricant (see How to Fix a Noisy Garage Door for maintenance and problem-solving tips). The door should operate smoothly and be properly balanced. Check the balance by disconnecting the opener and lowering the door halfway- the door should hold its position. If it doesn’t, adjust the spring tension or replace the springs.

Dallas Texas, Plano TX, Garland TX, Highland Village, Lakewood, Las Colinas, Lewisville, Little Elm, Grapevine, Haltom City, Hurst, Keller, Forney, Carrollton, McKinney TX, Murphy Texas, Oak Lawn, Arlington TX, Parker TX, Plano, Preston Hollow, Richardson TX, Denton, Addison, Allen, Bedford, Coppell, Crowley, DeSoto, Euless, Flower Mound, Rockwall Texas, Garland Texas, Rowlett TX, Sachse TX, The Colony TX, Lavon Texas, Fort Worth TX, East Dallas, North Dallas, Wylie TX, White Rock Lake, area Lakewood, North Richland Hills TX, Benbrook, Burleson, Waxahachie, Red Oak, Irving TX, Mesquite TX
Sometimes, people unplug their power source and then wonder why their garage door opener fails to work. Sounds ridiculous, I know, but it does happen. Make sure that your garage door opener is plugged into a working outlet. Outlets sometimes go out without warning, so you can check to see if the outlet is working by plugging another working electronic device into it. Also, check your circuit breaker, fuse, or GFCI.
A1 Garage Door Service is known for providing only the best value for money. We always aim for the best possible customer service and experience, reasonable costs for our products and services, give FREE estimates and FREE professional advice as well as amazing deals and discounts when you book our service. What’s more, we GUARANTEE that we service all manufacturer warranties, including lifetime warranties. What more can you ask for?
If you have two torsion springs on your garage door, the good spring will most likely keep the cables on the drums when the other spring breaks. This makes it much easier to lift because the good spring will be pulling half the weight of the garage door. You can also use the garage door opener to help assist while someone lifts the door and acts as the broken spring. Use extreme caution when doing this to prevent damage to your garage door or injury to a person.

Automatic Garage Door Repair Centennial Co


Our team of friendly, knowledgeable technicians have the industries best experience replacing broken springs on garage doors. Replacing a garage door spring can be very dangerous, and we highly encourage you to contact us to handle this repair today! If you have a high cycle application, our garage service team may be able to provide extended use high cycle springs. http://youtu.be/Z_eZc-kh40c
×