Nothing can be more frustrating than trying to open or close your garage door, but have it get stuck halfway. The most common reason this happens is due to a broken torsion spring, a part that is responsible for providing balance. It is a common problem that has many people saying “My garage door has a broken spring or is stuck, what do I do next”? If you are in this same boat, you’ll find the information below very useful.
Garage doors cause injury and property damage (including expensive damage to the door itself) in several different ways. The most common causes of injury from garage door systems include falling doors, pinch points, improperly adjusted opener force settings and safety eyes, attempts at do-it-yourself repair without the proper knowledge or tools, and uncontrolled release of spring tension (on extension spring systems).

Garage Door Repair Installation Centennial Colorado 80016


Delivered on time, with the products described: springs, winding bats, & plastic bushing. Quick install, but apparently I measured wrong, so these total length I bought was larger (which is good as there is less stress on the spring). However this did mean that I needed more than the generic rule of 30 1/4-turns of preload. I wound up with 38 1/4-turns per side for the door to balance when open 3' (per familyhandyman.com recommendations). Would definitely do it again.
While there are times you may be able to fix the problem yourself, there are many reasons it may be best to leave the garage door repair up to the professionals. Knowing what’s wrong with your garage door may help you to determine if it is a problem you can tackle or if it’s time to call someone for assistance. To help you troubleshoot your garage door issues, here are the top 10 reasons your garage door won’t work.

After working on the car, you find a big oil stain on the driveway. Pulverize a scrap piece of drywall with a hammer (any new home construction site will have dumpsters full of waste pieces of drywall). Crumble the pulverized drywall with your hands and sprinkle on the stain. Leave it overnight, and rinse off in the morning. Reapply and brush in with a bristle broom in cases of stubborn stains.
Replacement spring procedure took me exactly 1 hours including preparation and clean-up for double aluminum garage door. Watch the DIY video on Youtube, save $$, be careful with winding the torsion springs. Rule of thumb: 7' height door garage= 7' x 4 (each 1/4 turn) + 1 = 29 turns (1/4 turn), 8' height door garage = 8' x 4 + 1 = 33 turns (1/4 turn), and so on....

Automatic Garage Door Repair Centennial Colorado 80016


Most home centers don't carry all the replacement parts you'll need for garage door spring replacement, and most garage door service companies won't sell you springs. So you may have to order the parts online and wait for the shipment to arrive. Garagedoorpartsusa.com and stardoorparts.com are two online sources . First, inspect the condition of your cables and brackets. If you see any frayed strands on the cables or rust on the bottom brackets, replace them now before they fail. Bottom brackets cost about $15 per set. Premium-quality cables (listed as “7x19”) last much longer than economy cables and cost only about $4 more. So it's smart to buy the better cables for about $12 per set. https://m.youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c
For commercial or residential doors, operators and accessories outside of the U.S. or Canada you can contact international. ​​​​​​Please be sure to include the following in your e-mail, so we can connect you with the Overhead Door™ Distributor that can best serve you: Contact Person, Phone Number (including local dialing code), Company Name, City and Country, Product(s) of interest (i.e. residential or commercial garage doors, operators and accessories), Name of Project (if any) and Project Specifications.​​​​​​​​​​​​ 

Automatic Garage Door Repair Centennial Colorado 80015


If you are not sure if your door had the correct springs, we recommend that you weigh your door using an analog scale. From my own field experience I would estimate that at least 10% of the doors have the incorrect springs on them. In addition to this, most manufacturers spring their doors using a 20 pound window. We like to improve the garage door balance.
Homeowners have long been warned that torsion springs are extremely dangerous to work with and that replacing them must be left to a professional. But these claims are somewhat exaggerated. If you understand how they work, and you pay attention to what you're doing, you can replace them safely and surprisingly easily. Granted, they're a little spooky to work with at first (partly due to their reputation), but this is a good thing—you really don't want to forget that they're under tension. Thinking about every step — before you take it — is the key to staying safe.

Garage Door Repair Installation Centennial 80016


8.5 Inspect the bearing. Lube it with motor oil, spray lithium, or spray lubriplate grease. Do not use WD-40. If the shaft is worn and the bearing is seized and you can't free it, replace the bearing. Or, if you have bearings labeled "ADH" we recommend replacing them. I find very few other bearings that need to be replaced. However, if you do need to replace the bearing and you do not have a new one, you can replace it at a later date. You'll find a quick way to do this at our End Bearing Plate Replacement instruction page.
Garage Door Installation – This includes the installation of a new garage door. Includes the door itself, the track, cables, springs, hinges, handles, locks and rollers. It is the complete service and installation of a new door. We inspect all the parts, make adjustments to fit your garage opening, and service all elements during the installation process. Plus, we check to ensure all parts are in proper working order after installed.
Both types of springs are loaded, or under tension, when the door is closed. This gives them stored energy to help lift the door as it's being opened. When the door is all the way up, the springs are relaxed, or relatively so—they still may be under some tension. The mechanical difference between extension and torsion springs is that extension springs are loaded by stretching, or elongating, while torsion springs are loaded by twisting, creating torque.

We look out for the safety of our customers and their families. That’s why we do not sell garage door torsion springs separately to consumers, and it’s also why we recommend putting your broken garage door in the hands of our experienced technicians. At Garage Door Medics, we are licensed, bonded, and insured. We have completed thousands of garage door installations and spring repairs, and we make sure they are done safely and with the right springs for your garage door system.

A1 Garage Door Repair Centennial Colorado 80016


Even though most of us are likely used to seeing this small spring in place on our garage door, we don’t often think too much about it, and we simply count on it working when we need it to. Unfortunately, it doesn’t last forever and will eventually need to be replaced. It’s best to be proactive and notice when it begins to look worn down before it actually breaks. Otherwise, you may find yourself trying to open the garage door to drive to work one morning, only to find that the door won’t open because the spring is broken.
6.7 It's now time to unwind the spring. Firmly position yourself on a steady ladder beside the garage door. Next, insert the bar into one of the holes of the winding cone. Make sure it goes all the way in. It should click when your bar hits the core. If you want to test the force you will be handling before loosening the set screws, push up on the bar one quarter turn and bring it back down. Next, while grasping the other end of the bar firmly, loosen the set screws with an open-end wrench or small adjustable wrench loose enough to come free should the cone spin. Be prepared for the torque to be transferred to the bar.

Garage Door Repair How Much Centennial Co


I have 2 full house humidifiers that have stopped functioning right. There are new filters, fan runs, tanks are full of water but they are not empting into the base. They have worked for part of the winter and now nothing seems to help...I loosened the caps thinking I had them too tight..... nothing seems to work .I have had humidifiers for 20 years and this is the first time this has happened to me. The humidifiers are only 2 years old. Any suggestions?? 

If you have a Wayne Dalton TorqueMaster system (pictured below), the springs will be inside a tube. The only way to determine if one is broken is to lift the garage door manually. If the door is heavy (roughly 60lbs for a double car door), you most likely have a broken spring inside the TorqueMaster tube. Another way to tell if you have a broken spring in your Wayne Dalton Torquemaster tube is if the door goes up and won't go back down. http://m.www.youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c

While it would be wonderful if door springs lasted forever, the reality is that the simple act of opening and shutting the door multiple times every day isn’t easy. It’s hard on the springs, even though they’re built to do it. Most springs will last for a while, but they won’t last forever. The regular wear and tear of endlessly opening and shutting the door breaks them down and eventually, they’ll need to be replaced. https://m.youtube.com/embed/Z_eZc-kh40c


We look out for the safety of our customers and their families. That’s why we do not sell garage door torsion springs separately to consumers, and it’s also why we recommend putting your broken garage door in the hands of our experienced technicians. At Garage Door Medics, we are licensed, bonded, and insured. We have completed thousands of garage door installations and spring repairs, and we make sure they are done safely and with the right springs for your garage door system.

Affordable Garage Door Repair Centennial Co


Maybe the battery died or a spring broke, but you can't get into the garage to even see what the problem is. If the garage door is the only way in or out, or if you can't find the key to the door, you'll have to either find a way to break in or call a locksmith. As a preventative measure, it's smart to keep a spare key or install an emergency key release that would allow you to release the emergency disconnect to the operator so you can manually raise the door.

Garage Door Repair Images Centennial Colorado 80015


6.7 It's now time to unwind the spring. Firmly position yourself on a steady ladder beside the garage door. Next, insert the bar into one of the holes of the winding cone. Make sure it goes all the way in. It should click when your bar hits the core. If you want to test the force you will be handling before loosening the set screws, push up on the bar one quarter turn and bring it back down. Next, while grasping the other end of the bar firmly, loosen the set screws with an open-end wrench or small adjustable wrench loose enough to come free should the cone spin. Be prepared for the torque to be transferred to the bar.

Garage Door Repair How Much Centennial Co


When you know you’re in range and the door still won’t open, check to make sure the antenna is hanging down from the motor inside your garage and nothing is blocking it. Your antenna must be free from any obstruction to clearly receive the signal to open and close the door. Also inspect the antenna for any signs of damage. If it looks like there has been damage to the antenna, you’ll need to call your garage door technician to come out and replace it.
Product was received in two days and was as advertised. Installing these myself saved around $150 but it took around 2-3 hours. I would imagine everyone's experience is going to be different. These springs appear to be heavier duty than the ones they replaced. I couldn't use the same slots for tension as the old ones and it was trial and error in adjusting the length of my pull cable until the door closed as it should. I need to replace the springs on my other garage door and would think that will take less than an hour based on what I learned from the first install.
Sears offers two different drive mechanisms to accommodate your home and budget. If you're looking for a smooth and quiet opener for a garage door with rooms located above the garage or attached to the garage, the belt drive is going to be the best for you. You can also choose a chain drive opener, which is perfect for garages that are unattached to the home.

Jerrod the technician had answers to all my questions. He was very knowledgeable and very patiently explained what was going on with my garage door and the opener. I would definitely recommend A1 garage door service to friends and family. I was given options to either repair the door or replace it. I will get the door replaced when it gets non-functional from A1 garage door service.
I went on Garage Door Nation website to look at the conversion chart from 1 to 2 torsion springs. For my 1 spring, size 2"/0.250ID/30.5" length, they recommended 2 of 2"/0.207ID/24" length. I got this kit from Amazon for $64 with $11 overnight shipping even though I could get free shipping through Prime over the weekend, but I couldn't wait for 3 more painful days. Installed it followed YouTube video. Worked better than my old one, a lot quieter. Check the video if you want to install one yourself. Professional installation costs hundreds of $$$: http://youtube.com/watch?v=Z_eZc-kh40c&app=desktop
To install a single new garage door it should cost between $500 and $800. They demonstrate that the average homeowner can usually tackle such a project in a nine hour time span and a professional will be able to complete it in roughly five hours. Should it be a DIY project? Not really, most housing experts point out that it is a two-person job, requires advanced carpentry skills, and even knowledge of household electronic systems.
The electronics should also be inspected before or after investing in the cost of replacing the garage door panel to make sure your door will operate properly. The sensors prevent the door from closing on someone's foot or a pet. If they don't work, someone could be injured. Also check to make sure the door opener works, since you could otherwise be locked out of your garage.

Garage door manufacturers typically produce garage doors fitted with torsion springs that provide a minimum of 10,000 to 15,000 cycles and are guaranteed for three to seven years. One cycle is a single opening and closing sequence. Most manufacturers offer a 30,000 cycle spring. However, it is important to remember that if the weight of the garage door is increased by adding glass, additional insulation, or even several coats of paint, the life of the torsion spring may be greatly reduced. Additionally, springs at highly humid environments, such as coastal regions tend to have a significantly shorter cycle life, due to the corrosive cracking.
Unlike torsion springs, replacing extension springs has long been given the "green light" for DIYers, primarily because you can complete the job without having to deal with spring tension. The general process is simple and safe: open the door to relieve the spring tension (and secure it open with C-clamps in the tracks); disconnect the spring from the track bracket and the spring pulley, and disconnect the safety cable from one end; install the new spring, reinstall the pulley, and reconnect the safety cable, and you're done.
Roller doors ("Sheet Doors"-USA) are usually constructed of corrugated steel. They evolved from cover window and door coverings.[4] Other materials can be used (e.g.; transparent corrugated fibreglass) where strong impact resistance is not required. Corrugations give the door strength against impacts. A typical single car garage roller door has a preloaded spring inside the rolling mechanism. The spring reduces the effort required to open the door. Larger roller doors in commercial premises are not sprung (except USA) and use a manual pulley and chain system or a geared motor to raise and lower (roll up and roll down) the door. Roller doors cannot be effectively insulated.
Spring Issues - Unless it is due to an obstruction of some type, uneven movement of your garage door is likely caused by a problem with the spring mechanism. Roll-up doors generally have one center-mounted torsion spring. The tension on torsion springs is great. Therefore, it is necessary to call a professional for any repairs to this type of spring mechanism to avoid serious injury. Because replacement of these springs or cables in a garage door can take at least two or three hours of labor, costs can average $300 or more.
While there are times you may be able to fix the problem yourself, there are many reasons it may be best to leave the garage door repair up to the professionals. Knowing what’s wrong with your garage door may help you to determine if it is a problem you can tackle or if it’s time to call someone for assistance. To help you troubleshoot your garage door issues, here are the top 10 reasons your garage door won’t work.
Start your garage door spring replacement project by getting a rough measurement of your springs (length and diameter). Then measure the width and height of your door. Make sure the quote includes the trip charge, parts and labor. Then ask for a price based on 7x19 lift cables and double-life springs. Those items will give you more years of service and should only add $65 to the price.

Garage Door Repair Guy Centennial Co


Once the springs break, quite a bit of tension is put on the door cables, and they will often break next. When these cables break, they will snap and forcibly fly out like a broken rubber band. Think about how much it hurts to be snapped by a broken rubber band, and then multiply it by a hundred to account for the size and weight of the garage door cables. https://www.youtube.com/e/Z_eZc-kh40c
×