If you have two torsion springs on your garage door, the good spring will most likely keep the cables on the drums when the other spring breaks. This makes it much easier to lift because the good spring will be pulling half the weight of the garage door. You can also use the garage door opener to help assist while someone lifts the door and acts as the broken spring. Use extreme caution when doing this to prevent damage to your garage door or injury to a person.
Your door’s torsion spring is located approximately one foot from the top section of your door when it is closed. It consists of two large coil springs, and is approximately the length of your arm. Its purpose is to balance the weight of your door so that a door weighing between 160 and 185 pounds is practically weightless to lift. As such, it makes it possible for a garage door opener to raise the door using only ten pounds of pressure.
If your garage door is not opening or has become jammed, you may need to replace the garage door cables. Unless you have the proper tools and know-how, this is a job best left to a professional due to the weight of the garage door and the extreme tension of the springs. The cost of repair will vary depending on your location, the length of the cables you need, and the time it takes the pro to do the replacement.
If the door closes but then immediately pops open again, you'll need to check the limit settings, which help the mechanism determine how far to move the door in order to close it properly. If the settings are off, the door will hit the ground before the opener believes it should. It will assume that it has hit an obstacle and will automatically backtrack to avoid damage. Check the owner's manual or the buttons on the motor to adjust the limit settings. It may take some trial and error to get the setting just right.

If the door only goes up six inches and stops, or moves very slowly when using your remote, you could have a broken spring as well. Some customers will notice that the top section of their door is bent or that the door falls very quickly when lowering. Your door may be “crooked” or jerky when going up and down, and both of these signs indicate your torsion spring is in poor condition and very likely to break in the near future. Any time you hear a loud “popping” noise while operating, you should inspect your torsion spring immediately for signs of damage.
	6.4 Test the fit of the bar in the cone before loosening a set screw. Insert one end of your winding bar into one of the holes of the winding cone. Pull down on the bar slightly to make sure the set screws are tight. Position your ruler between the bar and the garage door. Move the bottom of the bar from side to side and measure the play. It should be less than an inch and a half. If it is over 2" either get someone else to change your springs or have someone make some bars that will properly fit the cones.

A garage door that has a broken spring has nothing to support its weight. The size of the door and the type of spring system determines how difficult opening the door will be. A garage door should not be opened until the spring is repaired. However, when you need to get your car out of the garage, it may be necessary if you cannot wait for the repairman. Use extreme care when opening a garage door in this manner.
Nothing can be more frustrating than trying to open or close your garage door, but have it get stuck halfway. The most common reason this happens is due to a broken torsion spring, a part that is responsible for providing balance. It is a common problem that has many people saying “My garage door has a broken spring or is stuck, what do I do next”? If you are in this same boat, you’ll find the information below very useful. https://www.youtube.com/watch?feature=youtube_gdata&v=Z_eZc-kh40c
Delivered on time, with the products described: springs, winding bats, & plastic bushing. Quick install, but apparently I measured wrong, so these total length I bought was larger (which is good as there is less stress on the spring). However this did mean that I needed more than the generic rule of 30 1/4-turns of preload. I wound up with 38 1/4-turns per side for the door to balance when open 3' (per familyhandyman.com recommendations). Would definitely do it again.
I PAID 700.00 DOLLORS TO GET THE 2 SPRINGE REPLACED WITH TOW DIFFERENT SPRINGS AND BOTH END BEARINGS PLUS INSTATTING THEM. tHIS IS ON A SATURDAY EVENING. aFTER ALL THAT i PAID BY CREDIT CARD THA THE INSTALL COULD SWIPE ON HIS PHONE. hE SAID AT THAT TIME I WOULD RECIEVE MY INVOICE VIA EMAIL. I didn,t think about it until another repair man came today 3/9/16 and he showed me that the bar that goes from one side to the other, had a bow in it of 3 inches just frome one side to the other. With this it will make the new bearings ware out faster. I trusted them to do the job right, But when i called to tell them that they replied that it was passed the 30 day warranty and they would do nothing more.

Action Garage Door Repair Centennial Co


"We had an unusual repair requirement. We have horizontal sliding steel doors on our 1950's equipment shed. The upper track was damaged by a roofer's forklift while they were loading supplies onto the roof. The track is made out of very heavy steel, not like the track in today's doors. Toby, responded to my request very quickly and came out of his way to inspect the damage. Although it was not something that he had encountered before, he was able to fix the track and the door is operating better than it has in years. Thank you."
With over 300 independently moving parts, your garage door is a deceptively complex piece of equipment. To help prevent malfunctions and break-downs, it is a good idea to occasionally perform a garage door tune-up to keep all of these parts in good working order. A regular tune-up service by a Sears professional can prevent unexpected door problems and prolong the life of your existing equipment.
Single panel doors are constructed from one monolithic panel. From the closed position a single panel door swings up and overhead with a hinge on each side (known as jamb type hardware) to the fully open position. A disadvantage of monolithic panel doors is that the swing up arc of the door occurs partially outside the garage. This means a vehicle must stop and park several feet in front of the door to avoid being hit by the garage door when it is opened. https://youtube.com/watch?feature=youtu.be&v=Z_eZc-kh40c
There are knobs or dials located somewhere on your garage door motor that you can use to adjust the limit settings. The exact location and resetting procedures will vary depending on the brand and model of garage door you have. Your owner’s manual should have more specific information on how to adjust your limits. You may need to experiment with a few adjustments before finally getting the correct setting. If you find that adjusting the limit settings isn’t working, it might be time to call a technician to come and help get your garage door to stay closed.

Eric Jonas has been writing in small-business advertising and local community newsletters since 1998. Prior to his writing career, he became a licensed level II gas technician and continues to work in the field, also authoring educational newsletters for others in the business. Jonas is currently a graduate student with a Bachelor of Arts in English and rhetoric from McMaster University. https://youtube.com/v/Z_eZc-kh40c
×