If you use the correct tools and follow our instructions, you can rebuild the entire torsion spring system in just a few hours, without any side trips to the ER. We won't cover how to replace garage door extension spring systems in this story. But we'll show you garage door spring replacement on the more common torsion springs, the kind that mount on a bar above the garage door. http://www.youtube.com/v/Z_eZc-kh40c&feature=share
7.5 Slide both springs out toward the cable drums. This is often the hardest part of the job. You may need to file away swollen shaft, set screw burs, drywall or paint. If the shaft is distorted because the garage door installer overtightened the set screws, file the shaft, insert a bar into the cone and tap the bar with a hammer until the cone passes over the enlarged portion of shaft.
If you have a steel door, but want the look of a wood one, it is not necessary to change your entire garage door. Often, it may be possible to mimic the look of wood with skillful painting. Your local home improvement store may be able to provide good advice about the type of paint and brushes needed to mimic the look of wood for your particular door material.
Torsion-spring doors have a drum-like pulley at each end of the metal rod that runs through the springs. Each pulley has a cable attached to the bottom of the door. The springs and pulleys are fixed to the rod so they all rotate together. When the door closes, the rod turns and winds up the springs, creating tension. When the door opens, the springs release the tension and turn the rod in the opposite direction.
Gather the supplies and tools needed for changing the springs safely. In addition to the torsion springs you'll need a minimum of one or two 10" vise grips, an adjustable wrench, and two 1/2" X 18" winding bars. Most hardware stores sell 1/2" X 36" steel rods that can be cut in half. You'll also need a firm ladder and a rag for cleaning your hands. A ruler and a file may also be necessary; a socket wrench and sockets would shorten the time required. Finally, make sure your garage is lighted well.

Garage Door Repair Bracket Centennial Co 80016


Garage door springs offset the weight of a garage door and allow the door to be opened and closed easily, either by hand or by an automatic garage door opener. The high-tension steel in the springs has a limited lifespan, and over time, the springs lose their effectiveness. Garage door springs come in levels of quality—they may be described as "10,000-use" or "20,000-use" springs, for example. This may sound like a very large number, but when you consider that a garage door might be opened four or five times a day, every day, every year, it becomes clear that there is a limited lifespan for these critical garage door parts.
Interested in garage door installation? You don’t have to know how to install a garage door or how to install a garage door opener. Lowe’s has you covered with professional, independent garage door installers to manage the job from taking measurements to the final garage door opener installation. Why take the time to learn how to install garage doors or how to install garage door openers? Invest less time and manage garage door installation costs. Contact Lowe’s for your project services today.
Vincent was professional, informative, personable, efficient, and cleaned up his work area as he worked. I told him and now I am telling you... He my "Jordan" of garages. Give him a raise or at least a bonus. Thank you for sending him for my install. I am extremely pleased with my garage opener & with his install and information I am confident in its operation. Thank you.
For example, low headroom garage doors often have cable drums on the outside of the end plate and the torsion springs usually wind down rather than up. They normally have left wind springs mounted on the left side of the spring anchor bracket and right wind springs mounted on the right side of the bracket. The first part on the shaft beyond each torsion spring is the end bearing plate. Just beyond the end bearing plate is the cable drum. On these the cable often runs on the front of the cable drum. The bottom of the cable is attached to a bracket that wraps around the front of and outside the vertical track.
Center and level the first section after you install the brackets. The door must be level even if the floor isn’t, so use shims under the section to level it. The rubber gasket on the bottom section will fill the gaps created by an unlevel floor. To hold the level in place, tape it to the section. To hold the section in place, lightly toenail a 16d nail into the frame and bend it over the section. Add brackets and rollers before setting them in place and stack one section on top of another, toenailing as you go up.
Both types of springs are loaded, or under tension, when the door is closed. This gives them stored energy to help lift the door as it's being opened. When the door is all the way up, the springs are relaxed, or relatively so—they still may be under some tension. The mechanical difference between extension and torsion springs is that extension springs are loaded by stretching, or elongating, while torsion springs are loaded by twisting, creating torque.
We live in a recently completed townhouse that was built with double-wall construction. That construction method was touted by the builder as what would keep sound from penetrating between the units. But we can hear the next door neighbors' TV and stereo, and sometimes voices and even snoring, through the wall. While sometimes it's the volume, mostly it's the bass sounds coming through the wall. They say they don't hear us, but we keep our bass turned down. They crank up the bass, and they are not going to change that. They also are not going to do anything construction-wise to help from their side. What is the best way for us to try to block the low frequency/bass sounds from penetrating the existing wall into our side?
9.4 Slide the end of the shaft into the end bearing plate. Tighten the set screws an additional 1/4 to 1/2 turns beyond the point you finger-tightened them. Add an additional 1/4 turn if you could not find the original set screw indentations in the previous step. Heavier wooden garage doors may require an additional 1/4 turn. Caution: Under-tightening the drums could cause the drum to slip and the door to cock or fall. Over-tightening the set screws could damage the shaft or drum, resulting in the same problems. This is a critical step.
A garage door with a broken torsion spring can fall rapidly and cause injury or death. However, the most common danger comes when your torsion springs break and you decide to undertake the repair/replace them yourself. Torsion springs can be very dangerous, and you not only need the exact tools for the job, but also need to have a good knowledge of the mechanics involved. Some of the parts involved in such a process can be life threatening, and must be handled with care and precision, which is why it is always recommended that you call in a professional, rather than trying to handle a replacement or repair by yourself. Failure to do so may leave you with injuries and/or damage to your property.
10.4 Raise the second bar 90 degrees and insert the first bar. This is "three." Continue winding. If the spring shortens in length, unwind the spring and switch sides - the springs are on backward. Otherwise, continue winding until you reach a count of "30." This is 7 1/2 turns, which is normal for most 7' doors. Longer life springs are wound the same number of turns. Newer steel doors with only one strut on top often need only 7 1/4 turns. On 8' doors count to 34. Each time you insert a bar into the winding cone, listen for the click to let you know the bar is in all the way. Not inserting the bar all the way could cause the cone to explode.
These instructions are for doors with cable drums and cables that look similar to those in the picture below. The next part beyond the end of the spring assembly is the cable drum. The drum is cast aluminum alloy 4" in diameter and 12.6" in circumference around the flat portion. Just beyond the cable drum is the end bearing plate. The cable unwraps off the back of the drum between the drum and the garage wall or jamb and travels down alongside the door, inside the track brackets and behind the roller stems as shown.
To evaluate whether the problem lies with the door or the automatic opener, make sure the door is in the fully closed position, then disengage the opener trolly from the door by pulling the emergency release cord. Try to lift the garage door by hand. If the door opens smoothly by hand, the problem is with the opener. If the garage door still only opens halfway, the problem is with the door.

Does your garage door stop when it is going up? Did you hear a loud bang, similar to a gun shot? Do the torsion springs above your door seem separated? If so, you might just have a broken torsion garage door spring. Torsion springs are located above the garage door and they are what lift the actual weight of the garage door. Most doors weigh between 150 to 250 pounds and without working springs, the garage door opener cannot lift the door. Attempting to use a garage door opener to lift a garage door with a broken spring can cause numerous parts on the opener to break.


An extension spring counterbalance system consists of a pair of stretched springs running parallel to the horizontal tracks. The springs lift the door through a system of pulleys and counterbalance cables running from the bottom corner brackets through the pulleys. When the door is raised, the springs contract, thus lifting the door as the tension is released. Typically these springs are made of 11 gauge galvanized steel, and the lengths of these springs are based on the height of the garage door in question. Their lifting weight capacity can best be identified by the color that is painted on the ends of the springs.
We look out for the safety of our customers and their families. That’s why we do not sell garage door torsion springs separately to consumers, and it’s also why we recommend putting your broken garage door in the hands of our experienced technicians. At Garage Door Medics, we are licensed, bonded, and insured. We have completed thousands of garage door installations and spring repairs, and we make sure they are done safely and with the right springs for your garage door system.

Anytime Garage Door Repair Centennial Colorado 80015


The Torquemaster system has a lock built into each side on a double car door that will activate when a spring breaks causing the door to lock in the up position. It is very simple to deactivate this lock and get your door closed. But, you can guarantee you have a broken spring inside the Torquemaster tube on the side where the lock activated. You will need the spring inside replaced or have it converted over to a standard torsion spring set up, which is what we recommend and a service we perform quite frequently. A standard torsion spring will last 3 times longer than the small spring inside the Torquemaster tube.

Anytime Garage Door Repair Centennial Colorado 80016


10The type of garage door shown provides the necessary lift assistance with a “torque tube.” If you intend to use an opener, wait to install the tube. Otherwise, install the torque tube according to the manufacturer’s directions. Roll up the door about 4 feet to check for the alignment of the tracks, and make any adjustments. Then tighten all fasteners.

Garage Door Repair Emergency Centennial Colorado 80016


If your stuck garage door coincides with weather changes, you may need to adjust the pressure on the opener. Some openers have a force-adjustment mechanism that controls the force that's applied to operate the door. It's best to leave this adjustment to a garage door pro, as too much force may result in the door failing to stop when it should, posing a danger to people and objects in the door's path.
I have recently purchased a house with an older roof that needs to be restored soon. So, I am trying to decide on I should go with a metal roof other than shingles. If I install metal roofing over solid decking such as OSB or plywood, integrate with a properly insulated garret, there is very little noise difference compared to standard asphalt shingles. I have briefly read benefits and drawbacks of Metal roofing but as I listed before I should go to metal roofing and hiring a roofing contractor no matter its expensive or noisy anyhow, Your article has cleared a lot of misinterpretation I’ve had before.
We have had many concerns with our garage opener unit both safety issue and sleepless nights. At this time we are pleased that so far the unit is operating as it should.Hopefully we hope the issue of the unit opening by it self at early morning hours is solved. And if this is so, we want to Thank all involve in bring a satisfactory solution to this nightmare.

Action Garage Door Repair Centennial Co 80015


1. Garage door springs do almost all of the work of lifting your door regardless of the door being manually or automatically operated. The spring makes it possible for anyone to lift a product that might weigh one hundred pounds on the low end and many hundreds of pounds on the high end. Not only can anyone lift it – most can do it with one hand! In other words, the garage door spring does a lot of work.

5.1 With the cables still tight on the drums, mark the drums and torsion shaft at each end with a file or a marking pen. If at least one of the springs is still wound, don't touch the cable drums and don't grab the shaft. If the cable breaks, the drum could spin and the cable rip through muscle and bone. If the set screws aren't tight enough, the shaft could spin and cause injury.

Usually, when a garage door spring breaks the door has already closed or come down. In some instances, however, a spring can snap while the door is closing or in motion, causing the door to fall rapidly. In these situations, the door can become a safety concern for you and your family, so you should keep your distance and call a garage door professional as soon as possible. Garage doors are very heavy and can cause injury if not handled properly. When a garage door problem occurs, call a Sears Garage Door expert to help.

Anytime Garage Door Repair Centennial 80016


Get a price quote on a New Garage Door- Use our super-simple garage door designer to learn about the available options, pick the ones you like best, and send it to us for a free quote. It's the fastest way to shop for a garage door on the web. In less than 10 minutes, you'll have a much better idea what you want and get a price without sales pressure. Click garage door designer to get started...
Standard torsion springs (about $40 each) have a service life of 7,000 to 10,000 open/close cycles. However, you can buy double-life (25,000 cycles) replacement springs for about $65 per spring. If you have a two-spring setup and one spring breaks, the second spring will break soon. So replace them both at the same time. To get the right springs for your door, you'll have to provide the supplier some details. Here's how:
Doors come with one or two torsion springs. If either spring is broken, the garage door opener may struggle to lift the weight of the door or fail to open the door at all. If a spring is broken, call a professional for service as these can be very dangerous to work with. Don’t try to open the door until a professional comes to inspect it and replace the springs. Springs can only be used for a certain number of open and close cycles, and over time they will eventually break and need replacing.

Garage Door Repair Centennial 80016


The technician did a wonderful job - arrived on time and completed the job in less than 2 hours. I would have given him a 5 on everything if he had returned to add the additional piece (a piece that is fixed to the door frame for better insulation) to my door on the outside on the day he said he would come back. The piece he brought was of wrong color and he said he would be back with the right color the first day after New Year's Day to put up the piece. I hope he can come back soon.

Ace Garage Door Repair Centennial Co


If your garage door is equipped with extension springs (usually seen on single car garages), the cable and pulley might be hanging down when the spring break's. Extension springs use a two pulley system on each side of the door to lift the garage door up and down. When the spring break's everything goes haywire, causing the cables to become twisted or even frayed when they catch on the metal edge of the track. There is a lot of force being released when a garage door spring breaks.
Most home centers don't carry all the replacement parts you'll need for garage door spring replacement, and most garage door service companies won't sell you springs. So you may have to order the parts online and wait for the shipment to arrive. Garagedoorpartsusa.com and stardoorparts.com are two online sources . First, inspect the condition of your cables and brackets. If you see any frayed strands on the cables or rust on the bottom brackets, replace them now before they fail. Bottom brackets cost about $15 per set. Premium-quality cables (listed as “7x19”) last much longer than economy cables and cost only about $4 more. So it's smart to buy the better cables for about $12 per set. https://m.youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c
Since garage doors come in all weights and sizes, the right springs need to be installed in order to properly balance the door. If a technician puts the wrong spring on your door, not only will this damage your garage door system, but it will cause the garage door opener to do more work than it was built to do. This is why Precision technicians only install the right springs for the door's weight and check their work by performing a balance test.
The national average for garage door repair cost is between $80 and $110. Some of the factors that affect your garage door repair cost are the type of springs (most often torsion or extension), the size and weight of the door, and the door material. Many garage door pros will charge a service fee to visit your house and determine the problem. Often, the service fee includes a set amount of labor. One example of this is an $80 service fee that includes the first hour of work plus testing and inspecting your garage door and garage door opener, while another pro may charge $150 for the same standard service call.    https://m.youtu.be/Z_eZc-kh40c
×