While it would be wonderful if door springs lasted forever, the reality is that the simple act of opening and shutting the door multiple times every day isn’t easy. It’s hard on the springs, even though they’re built to do it. Most springs will last for a while, but they won’t last forever. The regular wear and tear of endlessly opening and shutting the door breaks them down and eventually, they’ll need to be replaced. https://youtube.com/e/Z_eZc-kh40c?app=desktop
When I called to schedule the repair service, I was transferrd 5 times and spoke with 6 service reps. Each rep was very confused by my request to get my garage door repaired. One rep actually told me that Sears doesn't repair garage doors. I had to tell her that Sears installed the door. When I finally found a rep who could schedule my service, it took one week for the appointment. https://www.youtube.com/watch?v=Z_eZc-kh40c&feature=youtube_gdata
Plus, we carry all the best and high quality products from the top garage door brands. Whatever is your requirement or need for your garage door, we are sure to have them in our comprehensive inventory. We have garage doors in different styles, materials, colors, designs and what-have-you. If you still cannot find what you are looking for, we can always source them out for you.
I went on Garage Door Nation website to look at the conversion chart from 1 to 2 torsion springs. For my 1 spring, size 2"/0.250ID/30.5" length, they recommended 2 of 2"/0.207ID/24" length. I got this kit from Amazon for $64 with $11 overnight shipping even though I could get free shipping through Prime over the weekend, but I couldn't wait for 3 more painful days. Installed it followed YouTube video. Worked better than my old one, a lot quieter. Check the video if you want to install one yourself. Professional installation costs hundreds of $$$:

Garage Door Repair Centennial 80015


Garage doors cause injury and property damage (including expensive damage to the door itself) in several different ways. The most common causes of injury from garage door systems include falling doors, pinch points, improperly adjusted opener force settings and safety eyes, attempts at do-it-yourself repair without the proper knowledge or tools, and uncontrolled release of spring tension (on extension spring systems).

Garage Door Repair Installation Centennial Colorado 80016


A spring replacement is one of the most common repairs required on a garage door. These springs come in varying sizes and act as a balance, lifting over 90% of the garage door weight. This allows the door to easily open and close manually or with the assistance of an opener. Discount Garage Door's replacement springs ensure a longer life expectancy for the entire garage door system.
A garage door is a large door on a garage that opens either manually or by an electric motor (a garage door opener). Garage doors are frequently large enough to accommodate automobiles and other vehicles. Small garage doors may be made in a single panel that tilts up and back across the garage ceiling. Larger doors are usually made in several jointed panels that roll up on tracks across the garage ceiling, or into a roll above the doorway. The operating mechanism is spring-loaded or counterbalanced to offset the weight of the door and reduce human or motor effort required to operate the door. Less commonly, some garage doors slide or swing horizontally. Doors are made of wood, metal, or fiberglass, and may be insulated to prevent heat loss. Warehouses, bus garages and locomotive sheds have larger versions.
Broken Arrow, Owasso, Claremore, Central Oklahoma, Sapulpa, New Tulsa, Jenks, Glenpool, Prattville, Sand Springs, Leonard, Coweta, Kiefer, Oakhurst, Inola, Fair Oaks, Verdigris, Lotsee, Sperry, Justice, Valley Park, Bixby, Mannford, Cleveland, Westport, Prue, Bethany, Yukon, Midwest City, Spencer, Newcastle, Harrah, Jones, Piedmont, Arcadia, Luther, Wellston, Dell City, Tuttle, Bridge Creek, Blanchard, Mustang, Noble, Goldsby
In the home improvement world there's a common recommendation regarding garage door spring repair: always leave it to the pros. This is sound advice, but it's not as hard-and-fast as most sources claim. The fact is, a handy homeowner who's competent with tools and has a basic understanding of mechanical systems can replace either type of garage door spring. The procedures are pretty simple, but they involve many steps that must be done in the proper order, just like the pros do it. It's also critical that you get the proper size replacement spring. If you think you're up to the task, look at online tutorials by garage door pros to see what's involved. Helpful videos explain how to measure your old springs and order the correct replacement size as well as how to do the job from start to finish.
If the door closes but then immediately pops open again, you'll need to check the limit settings, which help the mechanism determine how far to move the door in order to close it properly. If the settings are off, the door will hit the ground before the opener believes it should. It will assume that it has hit an obstacle and will automatically backtrack to avoid damage. Check the owner's manual or the buttons on the motor to adjust the limit settings. It may take some trial and error to get the setting just right.
When I called to schedule the repair service, I was transferrd 5 times and spoke with 6 service reps. Each rep was very confused by my request to get my garage door repaired. One rep actually told me that Sears doesn't repair garage doors. I had to tell her that Sears installed the door. When I finally found a rep who could schedule my service, it took one week for the appointment. https://www.youtube.com/watch?v=Z_eZc-kh40c&feature=youtube_gdata
From a big-box store, basic garage door cables can run between $8 and $20, depending on the product. Your pro may charge you a different cost if they provide the cables. Your cables may not need to be replaced if they have simply come off the track, but broken cables will need to be completely removed and replaced. In either instance, the pros will need to secure or take down the door; unwind the springs; reset or replace the rollers, cables, and drums; and then wind the springs once more. For example, a pro could reset cables that have come off the track for $129.99. The average national cost for a garage door repair specialist is $80 - $110 per hour and the typical cost to replace a broken garage door cable is anywhere from $130 to $200.

Garage Door Repair Images Centennial Co 80016


There are knobs or dials located somewhere on your garage door motor that you can use to adjust the limit settings. The exact location and resetting procedures will vary depending on the brand and model of garage door you have. Your owner’s manual should have more specific information on how to adjust your limits. You may need to experiment with a few adjustments before finally getting the correct setting. If you find that adjusting the limit settings isn’t working, it might be time to call a technician to come and help get your garage door to stay closed.
If you need to leave the door open until you can make repairs, block the door track on both sides so the door can't move, and unplug the garage door opener (if you have one). If you want to close the door, you can try closing it with the opener, making sure there's nothing in the door's path in case something goes wrong. However, this will put some strain on the opener. Alternatively, you can have a few strong helpers hold the door while you disconnect it from the opener and carefully close the door manually—again, it will be very heavy.

Garage Door Repair And Service Centennial Co


Measure area labeled headroom (5), which is the distance between the top of the door opening (jamb header) and the ceiling (or floor joist). 10" is required for the standard extension spring or EZ-SET® Extension Spring System while 12" is required for a standard torsion spring and EZ-SET® Torsion Spring System. If you have restricted headroom, special hardware is available. Additional headroom is required for installation of an automatic garage door opener. NOTE: If garage door height extends above the opening, the headroom measurement should be adjusted proportionately. 

Torsion-spring doors have a drum-like pulley at each end of the metal rod that runs through the springs. Each pulley has a cable attached to the bottom of the door. The springs and pulleys are fixed to the rod so they all rotate together. When the door closes, the rod turns and winds up the springs, creating tension. When the door opens, the springs release the tension and turn the rod in the opposite direction. http://youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c
On one-piece doors with side springs, you open the door to relieve the spring tension, and simply swap out the springs on the opener-arm mechanism; there are no cables or pulleys to deal with, and the springs have internal safety rods. Some doors have tensioners that maintain moderate tension when the door is open all the way, and on these you'll have to loosen the tensioner in order to remove the spring.

Garage Door Repair Estimates Centennial 80016


Sometimes, you’ll notice that your garage door closes all the way and then immediately goes back up instead of staying in the closed position. This issue usually arises with brand new garage doors that were just installed or older models that may need to be reset. If this happens, the most likely culprit is the open and close limit settings of your garage door opener.
Opening the door yourself is recommended only during an emergency, as there is an increased risk of it getting stuck again-or worse yet, crashing down on top of you. Moving a wooden door could cause damage to the opener, or the top of a steel door might bend underneath the pressure. If you must open the door long enough to drive underneath it, you may want to prop up either side with some 2×4 pieces of lumber to provide added stability. You could also secure your door to its tracks using a pair of vise grips or a couple of c-clamps.
Your dream car is parked in out of the elements, but it's not secure because the garage door won't lock. Most garage doors have two horizontal bars that move out from the center of the door into slots along the side of the door in the door track, effectively locking the door in place. Over time, these bars can shift slightly out of position so that they are no longer correctly aligned with the locking slots. To realign the bars, unscrew the guide brackets on the edges of the door so that they are loose enough to move, and then reposition them so that they smoothly guide the locking bars into the locking slots. Lubricate the lock mechanism with machine oil and you're done.

Another scenario is the garage door goes up very slowly when using the automatic opener. Some garage door openers have DC motors that start off slow when opening and then kick into a higher speed. If you have a broken spring, the opener might stay in the slower speed due to the heavy weight of the garage door. If this happens to you, close the garage door and pull the emergency release rope. Next, try to lift the door. If it is really heavy, then you most likely have a broken garage door spring.


4.4 Take the spring on the left and place it at the left end of the door as pictured here. Notice that the end of the wire points to the right toward the center of the door. This is a right wind torsion spring. It will go above the garage door on the left side of the spring anchor bracket. The winding cone at the other end of this spring is usually painted red.
"Mile High garage called shortly after submitting my request and set an appointment to have a repair man show up shortly after. They went over everything I needed to get done and gave me several pricing options to fix initial need and alleviate future issues. Work was done in a timely manner and customer service was great. Mile High garage called shortly after submitting my request and set an appointment to have a repair man show up shortly after. They went over everything I needed to get done and gave me several pricing options to fix initial need and alleviate future issues. Work was done in a timely manner and customer service was great. "

Garage Door Repair Guy Centennial Co 80016


If one of your door springs just broke and you are looking for instructions to decide if you can change the spring or springs safely and correctly, this page should help. DO NOT OPEN AND CLOSE YOUR GARAGE DOOR. Wooden garage doors are heavy and will probably damage or ruin the opener. The tops of steel doors often bend when operated with broken springs.

Garage Door Repair Free Estimate Near Me Centennial 80016


Sometimes, you’ll notice that your garage door closes all the way and then immediately goes back up instead of staying in the closed position. This issue usually arises with brand new garage doors that were just installed or older models that may need to be reset. If this happens, the most likely culprit is the open and close limit settings of your garage door opener.

"Our garage door wouldn’t shut on sunny days and the tech came out. He explained my options (swap the “seeing” sensor with the other, or replace them). He tried swapping and it was still an issue so he replaced them. In addition, he adjusted the spring because the company that installed it last year did not adjust it properly. He was here for about two hours and charged us for only the sensor replacement. Will definitely be using this company again! Highly recommend them. "


The electronics should also be inspected before or after investing in the cost of replacing the garage door panel to make sure your door will operate properly. The sensors prevent the door from closing on someone's foot or a pet. If they don't work, someone could be injured. Also check to make sure the door opener works, since you could otherwise be locked out of your garage.

Containment cables. When old extension springs break, the springs and cables become heavy whips that damage cars and even injure people. To solve the whipping problem, manufacturers now offer containment cables that run through the center of side-mounted extension springs. If you have extension springs and don’t plan to replace your door, make sure the springs have these containment cables, or have a professional install them.

6.4 Test the fit of the bar in the cone before loosening a set screw. Insert one end of your winding bar into one of the holes of the winding cone. Pull down on the bar slightly to make sure the set screws are tight. Position your ruler between the bar and the garage door. Move the bottom of the bar from side to side and measure the play. It should be less than an inch and a half. If it is over 2" either get someone else to change your springs or have someone make some bars that will properly fit the cones.
For commercial or residential doors, operators and accessories outside of the U.S. or Canada you can contact international. ​​​​​​Please be sure to include the following in your e-mail, so we can connect you with the Overhead Door™ Distributor that can best serve you: Contact Person, Phone Number (including local dialing code), Company Name, City and Country, Product(s) of interest (i.e. residential or commercial garage doors, operators and accessories), Name of Project (if any) and Project Specifications.​​​​​​​​​​​​ 

Automatic Garage Door Repair Centennial Colorado 80015


To install a single new garage door it should cost between $500 and $800. They demonstrate that the average homeowner can usually tackle such a project in a nine hour time span and a professional will be able to complete it in roughly five hours. Should it be a DIY project? Not really, most housing experts point out that it is a two-person job, requires advanced carpentry skills, and even knowledge of household electronic systems.
Single panel doors can also be installed with (one piece track type hardware) that folds the door back with a single horizontal track on each side (which is mounted at the top of the wood frame) and a roller, (mounted to the top of the door on each side. A hinge on each side that attaches to the bottom of each side of garage door. Using track hardware, a car can be parked much closer to the door, as the whole door, when in the open position, rests completely inside of the garage door header. Track type hardware has much less arc when raising and lowering the garage door as opposed jamb type hardware.[citation needed]
The following procedures are based on my 30 years in the garage door industry. In spite of my high mechanical aptitude, even after 18 years in the trade I lost the end of my left index finger. A few years later I had five stitches in my right thumb, and a year later five stitches in my left thumb. In 2004 emergency room staffs dug steel out of my eye and sewed up my ring finger with eight stitches. The best I can do is help you minimize the risk of injury; that's all I can do for myself. I am not so naive as to think that I have made my last trip to the emergency room. Repairing garage doors, particularly replacing torsion springs, is dangerous work, whether you are a do-it-yourself homeowner or an experienced technician.
Garage door springs come in two styles: torsion (see above), which mounts on the header above the door, and extension (Photo 1), which floats above the upper roller track. In the past, extension springs were safer to install but didn’t have containment cables running through the center of the spring. Without cable, these springs become dangerous, heavy whips when they break. They also tend to be noisier than torsion springs, and we recommend you use them only if you don’t have the 12 in. of headroom above the door that a torsion spring requires. https://youtube.com/watch?v=Z_eZc-kh40c&app=desktop
Every homeowner can relate to how life's inconveniences are thrown at you at the worst possible times. The last thing you want to happen is have your car stuck in the garage when you need it most, especially when it's only been a couple months, weeks, or even days after your last garage door repair! That's why Precision leads by example and follows the industry's best practices in order to make the best recommendation to homeowners each time we step foot in a garage. http://www.youtube.com/v/Z_eZc-kh40c
×