The U.S. Consumer Product Safety Commission says that about 30,000 injuries linked to garage doors are now reported every year in the United States. Many of these injuries have involved bruised or broken extremities. However, some have included serious shoulder, back, and head injuries leading to permanent disability or even death. What is the cause of these garage door injuries? One leading cause has been homeowners trying to repair or replace their own garage door springs.

Aaa Garage Door Repair Centennial Colorado 80015


Product was received in two days and was as advertised. Installing these myself saved around $150 but it took around 2-3 hours. I would imagine everyone's experience is going to be different. These springs appear to be heavier duty than the ones they replaced. I couldn't use the same slots for tension as the old ones and it was trial and error in adjusting the length of my pull cable until the door closed as it should. I need to replace the springs on my other garage door and would think that will take less than an hour based on what I learned from the first install. https://www.youtube.com/v/Z_eZc-kh40c&feature=youtube_gdata
If this is the problem then you will be able to tell by seeing if your garage door rollers are literally off track. If your garage door panels are not damaged, then you do not need to replace your door. However, the rollers do need to be put back on the track which should be done by a professional. If you are looking for a garage door company that specializes in Garage Doors, Garage Door Repair, or Garage Door Openers, or are just looking for more information, please visit our website at precisiondoor.net. Remember, "We Fix Garage Doors Right"™.
	11.1 Many torsion spring replacement accidents occur from springs that are too strong. If the garage door stays on the floor by itself, remove the vise grip from the track. If the door is off the floor and the roller is against the vise grip, close the door with one hand and remove the vise grip with the other. If the springs are too strong, you have to restrain it from flying into the open position.

Sometimes, you’ll notice that your garage door closes all the way and then immediately goes back up instead of staying in the closed position. This issue usually arises with brand new garage doors that were just installed or older models that may need to be reset. If this happens, the most likely culprit is the open and close limit settings of your garage door opener.
We look out for the safety of our customers and their families. That’s why we do not sell garage door torsion springs separately to consumers, and it’s also why we recommend putting your broken garage door in the hands of our experienced technicians. At Garage Door Medics, we are licensed, bonded, and insured. We have completed thousands of garage door installations and spring repairs, and we make sure they are done safely and with the right springs for your garage door system.

A1 Garage Door Repair Centennial Colorado 80016


Test the door balance. A garage door should require only a few pounds of pressure to move it up and down. If springs wear out and lose their resiliency, a power garage door opener may need to work extra hard to lift the door. This can quickly wear out the motor on the opener. Replacing worn-out springs is usually a job for a professional technician.
There are two types of garage door springs: torsion and extension. Torsion springs are horizontal and located near the top of the garage door. Check for a gap between these springs indicating a break. Springs on the sides of the garage door are extension springs. Inspect them to see if one or both of them have broken. If you have a broken spring, call a garage door technician to fix it for you as soon as possible. Never operate a garage door with a broken spring; it could severely damage the door and the operating system. Never attempt to replace a broken spring on your own, either. Replacing broken garage door springs is very dangerous for anyone other than a certified, professional repair technician.
Changing your garage springs isn’t typically a DIY project and usually requires a professional. But it’s good to know when it’s time to find garage door spring replacements. To test your springs, disable your garage door opener if you have one, then raise the door manually. If it doesn’t stay in place on its own, it’s time to replace your garage springs.

SNAP... bang... boom. That is the sound of a garage door torsion spring breaking. It can be a very loud noise that sounds like a firecracker or gunshot. Springs are rated for a certain number of cycles and are the first thing that will break in your garage door assembly. Broken springs are the #1 source of customer calls for garage door repair companies. If you have a broken spring, you should NEVER try to open the door, as it can be very dangerous. This repair should be left to a professional or someone with the right tools and skills. https://www.youtube.com/watch?feature=youtu.be&v=Z_eZc-kh40c
Doors with extension springs have two sets of pulleys (which are sometimes called sheaves): one at the end of each spring and one at the top of the vertical door track. They also have two cables on each side. One cable attaches to the bottom of the door, runs up and over the pulley above the door and around the spring pulley and then attaches to the door track bracket. The other cables are safety cables that run through the middle of the springs and are fixed to a track bracket at both ends. These cables restrain the springs if they break under tension. All extension springs must have safety cables.

I PAID 700.00 DOLLORS TO GET THE 2 SPRINGE REPLACED WITH TOW DIFFERENT SPRINGS AND BOTH END BEARINGS PLUS INSTATTING THEM. tHIS IS ON A SATURDAY EVENING. aFTER ALL THAT i PAID BY CREDIT CARD THA THE INSTALL COULD SWIPE ON HIS PHONE. hE SAID AT THAT TIME I WOULD RECIEVE MY INVOICE VIA EMAIL. I didn,t think about it until another repair man came today 3/9/16 and he showed me that the bar that goes from one side to the other, had a bow in it of 3 inches just frome one side to the other. With this it will make the new bearings ware out faster. I trusted them to do the job right, But when i called to tell them that they replied that it was passed the 30 day warranty and they would do nothing more.

Action Garage Door Repair Centennial Co


The U.S. Consumer Product Safety Commission says that about 30,000 injuries linked to garage doors are now reported every year in the United States. Many of these injuries have involved bruised or broken extremities. However, some have included serious shoulder, back, and head injuries leading to permanent disability or even death. What is the cause of these garage door injuries? One leading cause has been homeowners trying to repair or replace their own garage door springs.
Maybe the battery died or a spring broke, but you can't get into the garage to even see what the problem is. If the garage door is the only way in or out, or if you can't find the key to the door, you'll have to either find a way to break in or call a locksmith. As a preventative measure, it's smart to keep a spare key or install an emergency key release that would allow you to release the emergency disconnect to the operator so you can manually raise the door. https://youtube.com/embed/Z_eZc-kh40c
NEVER use screwdrivers, pin punches or pliers handles to wind or unwind a torsion spring. Trust us: This is the best way to wind up in the hospital. Don't even think about doing this job without a proper set of winding bars. You can buy a set of professional hardened-steel winding bars for about $25 from online suppliers. (Garagedoorpartsusa.com and stardoorparts.com are two online sources that sell winding bars, springs and other parts.) Professional winding bars work with 1/2-in. and 7/16-in. winding cones. If your winding cones have 1/2-in. openings, you can make your own winding bars by cutting a 36-in. length of 1/2-in.-diameter round bar stock in half (buy round bar stock from any hardware or home center). Just file a smooth bevel on each end so it slides into the winding cone holes easier.
10.3 At this point you will wind the spring. Notice that the end of the spring on the winding cone points up when facing you. You will wind both springs up and counter intuitively as if you are trying to unscrew the winding cones from the ends of the springs. Begin by turning the spring up 1/4 turn until it meets resistance. This is your first quarter turn. Count "one." Next, insert the bar and raise it 90 degrees. Insert the second bar. This is "two." As you wind the spring it should grow in length the thickness of one coil for every turn. The cone should cover your mark after the first couple turns. Many garage door tradesmen mark the torsion springs with chalk or paint, but this often generates confusion.
Annual maintenance. Make an annual check of all nuts and bolts on rails and rollers to make sure they’re firmly tightened. Check the condition of all cables to make sure they’re not worn or frayed. Lubricate rollers and springs with a garage-door lubricant (see How to Fix a Noisy Garage Door for maintenance and problem-solving tips). The door should operate smoothly and be properly balanced. Check the balance by disconnecting the opener and lowering the door halfway- the door should hold its position. If it doesn’t, adjust the spring tension or replace the springs.
While it would be wonderful if door springs lasted forever, the reality is that the simple act of opening and shutting the door multiple times every day isn’t easy. It’s hard on the springs, even though they’re built to do it. Most springs will last for a while, but they won’t last forever. The regular wear and tear of endlessly opening and shutting the door breaks them down and eventually, they’ll need to be replaced. https://youtube.com/e/Z_eZc-kh40c?app=desktop
6.4 Test the fit of the bar in the cone before loosening a set screw. Insert one end of your winding bar into one of the holes of the winding cone. Pull down on the bar slightly to make sure the set screws are tight. Position your ruler between the bar and the garage door. Move the bottom of the bar from side to side and measure the play. It should be less than an inch and a half. If it is over 2" either get someone else to change your springs or have someone make some bars that will properly fit the cones.

Garage Door Repair Free Quote Centennial Colorado


9.8 Twist the garage door shaft to tighten the cable on the drum. While twisting, vise grip the shaft as shown to keep the cable tight on the drum. The top of the vise grip should be tight against the garage header. This will keep the cable snug on the first drum while you install the cable on the other drum and position it in place. It also keeps the shaft from turning and the cables peeling off when you wind the springs. That one grip can save many hours of walking back and forth and having to level and re-level the garage door after winding the torsion springs.

Ace Garage Door Repair Centennial Co 80016


In order to prevent injury, garage doors automatically reverse if they come into contact with an obstacle. When the door closes halfway but then reverses for no apparent reason, this may be a sign that there is something preventing it from closing, something that you can't see. Check the tracks for stuff like dirt, rocks, bits of trash, or other debris. Give the tracks a wipe-down to dislodge anything that might be getting in the way. https://youtube.com/watch?v=Z_eZc-kh40c
×