Extension spring systems should always be restrained by a safety cable that runs through the middle of the spring, tying off to a solid point at the rear and front of the horizontal door track. Extension springs represent a hazard to bystanders when a spring, pulley, or cable breaks under tension. Metal parts from extension spring systems can suddenly be launched.

Garage Door Repair Centennial Colorado 80016


If you use the correct tools and follow our instructions, you can rebuild the entire torsion spring system in just a few hours, without any side trips to the ER. We won't cover how to replace garage door extension spring systems in this story. But we'll show you garage door spring replacement on the more common torsion springs, the kind that mount on a bar above the garage door.
When your garage door is stuck after a power outage, your whole day can suffer. Summer storms hit, your garage door opener gets caught in the crossfire, and before you know it, your car is being held hostage by your garage. While it stinks to have your garage door stuck open because of safety issues, it may be even more frustrating to have your cars trapped inside. Just like saying your dog was eating your homework as a kid, now you have to explain to your boss how your car is being held hostage. Good luck.

Repair Sagging Garage Doors – As doors and homes age, they can shift and move and sometimes this results in a garage door that needs to be realigned or reinforced. We will send a technician to your home to adjust the doors and to inspect the entire opening to make sure the door isn’t damaged. Once we understand the problem, we will fix the needed parts and make any adjustments to the door. 

Garage Door Repair Average Cost Centennial Colorado 80015


The electronics should also be inspected before or after investing in the cost of replacing the garage door panel to make sure your door will operate properly. The sensors prevent the door from closing on someone's foot or a pet. If they don't work, someone could be injured. Also check to make sure the door opener works, since you could otherwise be locked out of your garage.

Opening the door yourself is recommended only during an emergency, as there is an increased risk of it getting stuck again-or worse yet, crashing down on top of you. Moving a wooden door could cause damage to the opener, or the top of a steel door might bend underneath the pressure. If you must open the door long enough to drive underneath it, you may want to prop up either side with some 2×4 pieces of lumber to provide added stability. You could also secure your door to its tracks using a pair of vise grips or a couple of c-clamps.
There could be a few issues that might be causing your transmitters not to work properly. The most common reason could be that you’re simply out of range of your garage door. Each garage door and transmitter combo has a specific range it will function in. If you’re trying to open your garage door before you can even see your house, then chances are you’re just too far away. Try waiting until you turn into your driveway to hit your transmitter button, and you should have more success opening your garage door on the first try.
I went on Garage Door Nation website to look at the conversion chart from 1 to 2 torsion springs. For my 1 spring, size 2"/0.250ID/30.5" length, they recommended 2 of 2"/0.207ID/24" length. I got this kit from Amazon for $64 with $11 overnight shipping even though I could get free shipping through Prime over the weekend, but I couldn't wait for 3 more painful days. Installed it followed YouTube video. Worked better than my old one, a lot quieter. Check the video if you want to install one yourself. Professional installation costs hundreds of $$$: http://youtube.com/watch?v=Z_eZc-kh40c&app=desktop
If your torsion spring isn’t lifting your door or your door is stuck, it is best to not attempt fixing it on your own. Garage doors are very heavy and can be the source of great injury if not handled with care when a part is broken. At Advanced Garage Door Solutions, Inc., we are there for you to quickly fix the problem so that normal garage door function is restored. To learn more, call the Minneapolis office at 952-500-3921 or the St. Paul office at 651-769-7191 and request a free estimate. 

Garage Door Repair And Installation Centennial Co 80016


When your garage door is stuck after a power outage, your whole day can suffer. Summer storms hit, your garage door opener gets caught in the crossfire, and before you know it, your car is being held hostage by your garage. While it stinks to have your garage door stuck open because of safety issues, it may be even more frustrating to have your cars trapped inside. Just like saying your dog was eating your homework as a kid, now you have to explain to your boss how your car is being held hostage. Good luck.

We look out for the safety of our customers and their families. That’s why we do not sell garage door torsion springs separately to consumers, and it’s also why we recommend putting your broken garage door in the hands of our experienced technicians. At Garage Door Medics, we are licensed, bonded, and insured. We have completed thousands of garage door installations and spring repairs, and we make sure they are done safely and with the right springs for your garage door system.
Extension springs last 15,000 cycles. Every time the door goes up and down is one cycle. On average extension springs will last 7 to 12 years. For most people, you know you need to replace your extension springs because it snaps. Sometimes, however, when extension springs get older, they can lose their tension and the spring becomes elongated. This is rare but it does still happen. Basically, the coils are fatigued and when the door is up you can see gaps where the spring is not relaxing properly. When this happens, the spring is useless. It is best to replace the springs at this point rather than overworking the opener which will cause it to last a shorter life.
Replacing torsion springs is done with the door closed. You start by carefully unloading all of the springs (most standard-size doors have two; any broken spring will already be unloaded), using the winding bars. Then, you unbolt the springs from the central rod bracket, disconnect the cables from the pulleys, and loosen the pulleys and slide them off of the rod. Next, you swap out the springs, reinstall the pulleys and cables, and secure the inside ends of the springs to the central bracket. Finally, you wind up both springs (securing them with two setscrew bolts on the winding cones) and test the door for proper spring tension. Often, springs need an extra quarter-turn or two to get the door balance just right.
Aging garage door springs cause the door to effectively "weigh" more as the steel loses its resiliency. With new springs, a heavy garage door should take no more than about 10 pounds of force to lift into an open position. With springs nearing the end of their lifespan, the force required to lift the door can be considerably more, since a garage door may weigh 200 pounds or more.
When you hire a professional, the first thing they will do is turn off the power as a safety precaution.  They will then measure the existing door springs to make sure the new springs they order or have in stock fit accordingly.  With these new springs, they will unwind the existing springs and install the new ones in its place, tightening them with screws.  When tightened, the springs will be balanced, lubricated and the springs will be wound up.  Lastly, the door will be tested and the tracks will be lubricated to move efficiently.

In addition to the bodily risk involved, it’s simply not an easy task. There’s the possibility that you will not install it correctly. At worst, this creates the risk that the mechanism will fail at the wrong time and injure you or someone in your family. At best, this means it will malfunction, and you’ll have to call professionals to fix it. It will save time, money and potential heartache to simply call a professional to install your new door springs correctly the first time.
Squealing, screeching, or grinding noises from your garage door are usually indicative of a lack of lubricant or an accumulation of dirt or debris in the tracks. When removing debris, do not use harsh chemicals to clean the tracks. Once the track is clean, coat it with lubricant designed especially for garage doors, if possible. If you do not have access to this special type of lubricant, you can use WD-40 on the tracks and hardware.
"We had an unusual repair requirement. We have horizontal sliding steel doors on our 1950's equipment shed. The upper track was damaged by a roofer's forklift while they were loading supplies onto the roof. The track is made out of very heavy steel, not like the track in today's doors. Toby, responded to my request very quickly and came out of his way to inspect the damage. Although it was not something that he had encountered before, he was able to fix the track and the door is operating better than it has in years. Thank you."
Torsion springs are located above the opening of your door with springs that slide onto a bar. Extension spring systems can be found alongside the opening of the door. It's important to know whether or not a garage door company provides service for your needs. Precision's professionally trained technicians are fully equipped to work on torsion and extension spring systems. http://m.youtube.com/e/Z_eZc-kh40c
×