Order replacement springs. Many manufacturers and distributors only provide torsion springs to professionals, and won’t sell them directly to the customer. Luckily, they are available on the Internet, so search online to find replacement springs. Make sure they match the coil size, length, and interior diameter of the springs you removed. Also, be sure to order both a “left-hand” and a “right-hand” spring as the coils are wound in different directions.[8]

Sometimes, you’ll notice that your garage door closes all the way and then immediately goes back up instead of staying in the closed position. This issue usually arises with brand new garage doors that were just installed or older models that may need to be reset. If this happens, the most likely culprit is the open and close limit settings of your garage door opener.
11.2a Raise the garage door slowly. Check the door balance. If you have the correct springs the door should stay down when closed, half way when opened half way, and open when opened. If the door will drop to the floor by itself from the halfway point, add 1/4 turn of tension to each of the torsion springs. If the garage door won't stay on the floor, and if it pulls itself up when stopped halfway, close the door and remove 1/4 turn of tension from the springs.
The nucleus of any garage door system is its opener. Easily overlooked, garage door openers are highly complex pieces of equipment, often containing dozens of intricate parts that work simultaneously with one another to consistently raise and lower your door. You'll know that you're getting the best from Sears as it's the home to America's #1 Garage Door Opener Brand, Craftsman*.

If you have two torsion springs on your garage door, the good spring will most likely keep the cables on the drums when the other spring breaks. This makes it much easier to lift because the good spring will be pulling half the weight of the garage door. You can also use the garage door opener to help assist while someone lifts the door and acts as the broken spring. Use extreme caution when doing this to prevent damage to your garage door or injury to a person.

Action Garage Door Repair Centennial 80016


NEVER use screwdrivers, pin punches or pliers handles to wind or unwind a torsion spring. Trust us: This is the best way to wind up in the hospital. Don't even think about doing this job without a proper set of winding bars. You can buy a set of professional hardened-steel winding bars for about $25 from online suppliers. (Garagedoorpartsusa.com and stardoorparts.com are two online sources that sell winding bars, springs and other parts.) Professional winding bars work with 1/2-in. and 7/16-in. winding cones. If your winding cones have 1/2-in. openings, you can make your own winding bars by cutting a 36-in. length of 1/2-in.-diameter round bar stock in half (buy round bar stock from any hardware or home center). Just file a smooth bevel on each end so it slides into the winding cone holes easier. https://www.youtube.com/watch?v=Z_eZc-kh40c&app=m
Interested in garage door installation? You don’t have to know how to install a garage door or how to install a garage door opener. Lowe’s has you covered with professional, independent garage door installers to manage the job from taking measurements to the final garage door opener installation. Why take the time to learn how to install garage doors or how to install garage door openers? Invest less time and manage garage door installation costs. Contact Lowe’s for your project services today.
When one or both springs break, gravity takes over and you feel the full weight of the door when lifting or lowering it.  It may be possible to pull the door up by hand, although doing so will likely be very difficult. In most cases, two or more people are needed to raise the door high enough for you to drive your car out of the garage. While single garage doors can typically be lifted, double doors are nearly impossible to manipulate due to their excessive weight. http://m.www.youtube.com/embed/Z_eZc-kh40c
A standard double garage door is 7 ft. high by 16 ft. wide. Standard single doors are 7 ft. high by 8 or 9 ft. wide. Because the doors are so large, few home centers and only some garage door stores keep many doors in stock, so expect to order one instead of buying it off the shelf. Garage doors are available in wood, fiberglass and steel. Steel doors, like ours, are light, maintenance-free, affordable, readily available, and have an insulating value as high as R-19.
Slide the left spring onto the tube and add the cable drum. When your new springs arrive, put the new left spring (the 1 with the end facing up and to the left) on the torsion tube, making sure that the stationary cone on the end of the spring faces the center bracket. After sliding the new spring into place, replace the cable drum and insert the torsion bar into the left bearing bracket.[9]
With Garage Door Doctor, you can rest assured we will replace your springs correctly. We offer 2 types of springs – standard and high cycle. On a 7 foot tall door, our standard torsion springs will last 15,000 cycles and our high cycle torsion springs will last 50,000 cycles. How many years will this last you? That is based off only one thing – usage. For example, with standard torsion spring, if you use your door 4 times a day, you get just over 10 years of life. However, if you use your door 8 times a day, you would get just over 5 years of life. If you use door very little or if you are moving very soon, maybe standard springs would be best for you. If you use your door many times a day or if you don’t plan on moving for a while, high cycle springs would be best for you. Getting high cycle springs will ensure you won’t be stuck with a broken spring for many years to come. Either way, both types of torsion springs we offer work great – its just a matter of when the break again. Call Garage Door Doctor today to have your garage fixed properly! https://m.youtube.com/watch?v=Z_eZc-kh40c
We want to hear from you and encourage a lively discussion among our users. Please help us keep our site clean and safe by following our posting guidelines, and avoid disclosing personal or sensitive information such as bank account or phone numbers. Any comments posted under NerdWallet's official account are not reviewed or endorsed by representatives of financial institutions affiliated with the reviewed products, unless explicitly stated otherwise.
In most cases, only one spring breaks or wears out at a time, and you can get away with replacing just the failed spring. But this is a little like replacing old car tires one at a time. You'll get the best performance if all the springs are new and have the same strength. Extension springs are replaced individually, making it more tempting to replace just one. With torsion springs, you have to disassemble everything to replace either spring, so it makes sense to swap out both springs during the repair.
10.6 Here you will need to do three things at once. With your left hand, lift the bar just off the top of the door and pull it toward the center of the garage door. While lifting up and back, tap the top of the bar just under the winding cone with your other bar. Pulling the bar back toward the center of the door as you tap causes the spring cone to bind on the shaft and not slip back.
Maybe the battery died or a spring broke, but you can't get into the garage to even see what the problem is. If the garage door is the only way in or out, or if you can't find the key to the door, you'll have to either find a way to break in or call a locksmith. As a preventative measure, it's smart to keep a spare key or install an emergency key release that would allow you to release the emergency disconnect to the operator so you can manually raise the door. https://youtube.com/embed/Z_eZc-kh40c
×