4. It is also important to note that extension springs sometimes do not break but rather ‘stretch out’. This is easy to spot as the space between coils when the door is closed is normally consistent. When the spring fails without breaking the space between the coils will become very inconsistent. This condition is quite visible and if it exists the springs should be replaced (Know when to call quits with your garage door). 

When one or both springs break, gravity takes over and you feel the full weight of the door when lifting or lowering it.  It may be possible to pull the door up by hand, although doing so will likely be very difficult. In most cases, two or more people are needed to raise the door high enough for you to drive your car out of the garage. While single garage doors can typically be lifted, double doors are nearly impossible to manipulate due to their excessive weight. http://m.www.youtube.com/embed/Z_eZc-kh40c


7.5 Slide both springs out toward the cable drums. This is often the hardest part of the job. You may need to file away swollen shaft, set screw burs, drywall or paint. If the shaft is distorted because the garage door installer overtightened the set screws, file the shaft, insert a bar into the cone and tap the bar with a hammer until the cone passes over the enlarged portion of shaft.
The following procedures are based on my 30 years in the garage door industry. In spite of my high mechanical aptitude, even after 18 years in the trade I lost the end of my left index finger. A few years later I had five stitches in my right thumb, and a year later five stitches in my left thumb. In 2004 emergency room staffs dug steel out of my eye and sewed up my ring finger with eight stitches. The best I can do is help you minimize the risk of injury; that's all I can do for myself. I am not so naive as to think that I have made my last trip to the emergency room. Repairing garage doors, particularly replacing torsion springs, is dangerous work, whether you are a do-it-yourself homeowner or an experienced technician.
If you have a single-car garage, an extension spring will do the job. If you’re looking for a smoother motion and an ability to lift heavier doors, you may be better off selecting the torsion spring option. And if you have a two-car garage, your door will likely be too heavy for an extension spring. In this case, the torsion spring is the better choice.

Broken Arrow, Owasso, Claremore, Central Oklahoma, Sapulpa, New Tulsa, Jenks, Glenpool, Prattville, Sand Springs, Leonard, Coweta, Kiefer, Oakhurst, Inola, Fair Oaks, Verdigris, Lotsee, Sperry, Justice, Valley Park, Bixby, Mannford, Cleveland, Westport, Prue, Bethany, Yukon, Midwest City, Spencer, Newcastle, Harrah, Jones, Piedmont, Arcadia, Luther, Wellston, Dell City, Tuttle, Bridge Creek, Blanchard, Mustang, Noble, Goldsby


We have had many concerns with our garage opener unit both safety issue and sleepless nights. At this time we are pleased that so far the unit is operating as it should.Hopefully we hope the issue of the unit opening by it self at early morning hours is solved. And if this is so, we want to Thank all involve in bring a satisfactory solution to this nightmare.
At Custom Door and Gate, we’ve been installing and repairing garage doors since 1989. We know the ins-and-outs of residential garage door repair, and we can help you diagnose your garage door issues if you’re uncertain what the problem is. We handle everything from automatic garage door repair to garage door replacement. We provide repairs and service to customers in the North Carolina area. Call us today to answer your garage door questions or to schedule a repair with our skilled garage door technicians.

Maybe the battery died or a spring broke, but you can't get into the garage to even see what the problem is. If the garage door is the only way in or out, or if you can't find the key to the door, you'll have to either find a way to break in or call a locksmith. As a preventative measure, it's smart to keep a spare key or install an emergency key release that would allow you to release the emergency disconnect to the operator so you can manually raise the door. https://youtube.com/embed/Z_eZc-kh40c

Examine the garge door rollers, hinges, tracks, and other hardware for signs of damage that might cause the door to hang up. Lubricate the tracks and hardware with silicone spray or oil. Raise the door slowly, watching it as it lifts. See if it catches on a warped panel or support beam or if an obstruction in the path of the photo eye causes it to stop or reverse. Any part that protrudes into the path of the garage door can cause it to stop.
When a torsion spring is wound up, it grows 2” in length. This is because the spring starts to compress and the metal has to go somewhere. After the spring is wound, the winding cone is clamped down on the torsion shaft so it can turn the drums to wind the cables as the door goes up. Since the end of the spring is “set” on the shaft, a two-inch gap is left when the spring break's. This is the most definite way of determining you have a broken garage door spring. https://www.youtube.com/v/Z_eZc-kh40c&feature=youtu.be
10The type of garage door shown provides the necessary lift assistance with a “torque tube.” If you intend to use an opener, wait to install the tube. Otherwise, install the torque tube according to the manufacturer’s directions. Roll up the door about 4 feet to check for the alignment of the tracks, and make any adjustments. Then tighten all fasteners.

Garage Door Repair Free Estimate Centennial Colorado


Torsion-spring doors have a drum-like pulley at each end of the metal rod that runs through the springs. Each pulley has a cable attached to the bottom of the door. The springs and pulleys are fixed to the rod so they all rotate together. When the door closes, the rod turns and winds up the springs, creating tension. When the door opens, the springs release the tension and turn the rod in the opposite direction. http://youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c
1. Garage door springs do almost all of the work of lifting your door regardless of the door being manually or automatically operated. The spring makes it possible for anyone to lift a product that might weigh one hundred pounds on the low end and many hundreds of pounds on the high end. Not only can anyone lift it – most can do it with one hand! In other words, the garage door spring does a lot of work.

If your stuck garage door coincides with weather changes, you may need to adjust the pressure on the opener. Some openers have a force-adjustment mechanism that controls the force that's applied to operate the door. It's best to leave this adjustment to a garage door pro, as too much force may result in the door failing to stop when it should, posing a danger to people and objects in the door's path.
2.4 The same is true of Older Overhead, BarCol and Raynor torsion springs that have winding cones with inconsistent hole sizes. If you insert a 1/2" X 18" bar in some of these holes you can move the opposite end of the bar over four inches. Bars in newer cones move less than 1 1/2". I've had many of the older cones spin loose from my bars, the last one generating an $1800 emergency room bill. If your cones are like any of these, or if they have more than 2" of play, leave the job of installing torsion springs to a professional garage door mechanic.
If you have a Wayne Dalton TorqueMaster system (pictured below), the springs will be inside a tube. The only way to determine if one is broken is to lift the garage door manually. If the door is heavy (roughly 60lbs for a double car door), you most likely have a broken spring inside the TorqueMaster tube. Another way to tell if you have a broken spring in your Wayne Dalton Torquemaster tube is if the door goes up and won't go back down.
If your stuck garage door coincides with weather changes, you may need to adjust the pressure on the opener. Some openers have a force-adjustment mechanism that controls the force that's applied to operate the door. It's best to leave this adjustment to a garage door pro, as too much force may result in the door failing to stop when it should, posing a danger to people and objects in the door's path. https://www.youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c
Fiberglass and vinyl garage doors are composite units, combining a steel core behind a fiberglass or vinyl skin. They have also polyurethane insulated base sections, or other type of foam insulation. These premium doors can match steel garage doors, and be a realistic imitation of wood (namely fiberglass units), but they may be more expensive than steel units.
Eric Jonas has been writing in small-business advertising and local community newsletters since 1998. Prior to his writing career, he became a licensed level II gas technician and continues to work in the field, also authoring educational newsletters for others in the business. Jonas is currently a graduate student with a Bachelor of Arts in English and rhetoric from McMaster University.
A garage door with a broken torsion spring can fall rapidly and cause injury or death. However, the most common danger comes when your torsion springs break and you decide to undertake the repair/replace them yourself. Torsion springs can be very dangerous, and you not only need the exact tools for the job, but also need to have a good knowledge of the mechanics involved. Some of the parts involved in such a process can be life threatening, and must be handled with care and precision, which is why it is always recommended that you call in a professional, rather than trying to handle a replacement or repair by yourself. Failure to do so may leave you with injuries and/or damage to your property.
I never heard of Oak Glen before, but do recognize the mountain names. I wouldn't expect to find any towering Sequoias and Redwoods there because neither species is native to that part of California, and they do take some time to become towering. And I've never heard of any overlapping of their ranges. A more suitable house for this location might get inspiration from the Monolithic Dome in Yucaipa which survived a direct hit from a wildfire.

Garage Door Repair Cost Centennial Co 80016


Unlike torsion springs, replacing extension springs has long been given the "green light" for DIYers, primarily because you can complete the job without having to deal with spring tension. The general process is simple and safe: open the door to relieve the spring tension (and secure it open with C-clamps in the tracks); disconnect the spring from the track bracket and the spring pulley, and disconnect the safety cable from one end; install the new spring, reinstall the pulley, and reconnect the safety cable, and you're done.

The winding and unwinding is done at a metal fitting, called a winding cone, attached to the outside end of the spring. You stick a winding bar into one of the four holes in the cone and use the bar as a lever to turn the cone. Once you've completed a quarter turn, insert the other bar into a different hole in the cone and let the bar lever against the closed garage door to hold the spring tension. This allows you to move the original bar to repeat the process, alternating the bars with each quarter-turn. It takes about 30 quarter-turns to fully tension a standard torsion spring.
9.14 Slide the springs to the bracket. Double-check to make sure you have the right wound spring on the left side and the left wind spring on the right side. Turn the springs until the ends are facing you. The wire at the ends of both torsion springs here at the bracket should be pointing down. At the winding cones at the opposite ends, the spring wire points up. If not, reverse the springs. About once a month we get a phone call from a do-it-yourself customer who begins the conversation with, "I wound the garage door spring to about six turns and the spring came loose from the cone." We normally refer them back to this step and suggest they switch their springs.
On one-piece doors with side springs, you open the door to relieve the spring tension, and simply swap out the springs on the opener-arm mechanism; there are no cables or pulleys to deal with, and the springs have internal safety rods. Some doors have tensioners that maintain moderate tension when the door is open all the way, and on these you'll have to loosen the tensioner in order to remove the spring.
Your decision on whether to try and replace a broken spring may depend on what type of springs you have. Garage door springs come in two main types: extension and torsion. Identifying which type you have is easy. If your door system has a long, skinny spring running parallel to each horizontal door track, then you have extension springs. If your door has one or more beefy springs on a metal rod parallel to, and directly above, the door opening, then you have torsion springs. Both of these springs are found on standard sectional garage doors. If you happen to have an old one-piece, swing-up door with vertical springs at both sides, you also have a variety of extension springs, sometimes called side springs.

Garage Door Repair Cost Centennial 80016


Sears garage repair technicians are fast, with same-day, emergency repairs available in most areas. We can replace garage door broken springs, rollers, cables, hinges, sensors and weather seals. We can also adjust garage door tracks and springs to make sure your door operates smoothly. Having problems with your garage door opener? We can repair or replace that too. Check out our line of Craftsman Garage Door Openers. Craftsman is America’s #1 brand of garage door openers! 1

You may enter your information on this website, visit an in store associate or call our garage door repair team at the number at the top of this page. Within 24 hours you will receive a call from a local service provider to discuss your requested service. Afterwards, you will schedule a date and time for the service provider to come to your property.

Remove the clamps and pliers from the torsion tube and track, and lift the door about 3 ft. by hand. If the door springs are properly adjusted, the door should stay in place when you let go. If the door falls when you let go, add a quarter turn to each spring. Repeat if necessary. If the door continues to open on its own, release spring tension in quarter-turn increments until the door stays in place when you let go. Then reconnect the opener.
Another scenario is the garage door goes up very slowly when using the automatic opener. Some garage door openers have DC motors that start off slow when opening and then kick into a higher speed. If you have a broken spring, the opener might stay in the slower speed due to the heavy weight of the garage door. If this happens to you, close the garage door and pull the emergency release rope. Next, try to lift the door. If it is really heavy, then you most likely have a broken garage door spring.
9.9 Go to the other side of the garage door and insert the end of the cable into the drum. Rotate the drum until the cable is tight. Slide the drum against the bearing and push the shaft to the right. The marks should line up. If they don't, figure out why and correct the problem. It could be a stuck cable, the garage floor may have shifted, or the vertical angle that helps support the bearing plate may have loosened and shifted. Many garage doors have been installed with a gap between a drum and a bearing plate. The cable drums should always be flush against the race of the bearings.
The U.S. Consumer Product Safety Commission says that about 30,000 injuries linked to garage doors are now reported every year in the United States. Many of these injuries have involved bruised or broken extremities. However, some have included serious shoulder, back, and head injuries leading to permanent disability or even death. What is the cause of these garage door injuries? One leading cause has been homeowners trying to repair or replace their own garage door springs.
Install the center bearing and the right spring, then secure the cones. Slide the torsion bar to the left then add the center bearing. Slide the right spring onto the bar and press the bearing into the stationary cone. Connect both of the stationary cones to the center bracket with the nuts and bolts you removed previously. Remove the locking pliers or clamp from the center bracket.[10]

If you haven’t looked at garage doors lately, prepare to be pleasantly surprised. We’ve taken the garage door and made it stylish with designs to complement both classic and contemporary homes while still keeping the functionality you desire. A garage door can represent more than 30% of your home’s curb appeal, which makes choosing the right design especially important – and Home Depot has the widest selection available. With over 1,000 different garage door designs in wood, steel, composite, aluminum and glass, you’re sure to find the perfect style to transform your garage… and your home.
As the door is opened and closed over time, the steel in the springs can start to weaken as the door gradually becomes too heavy for them, rendering them less effective. The springs will eventually break, leaving the door closed. Torsion springs can also be affected by rust and cold weather. The good news is, the average garage door torsion springs will last somewhere between 5-7 years, and should last around 10,000 cycles. So, if you open and close your garage door 3-5 times a day for over 365 days in a year, you should get plenty of life out of your torsion springs.
11.2b If the springs you installed are too strong, and if you wind the springs the correct number of turns, the door will not stay down nor half way. The garage door will be hard to close. DO NOT REMOVE MORE THAN HALF A TURN OF SPRING TENSION TO CORRECT THE PROBLEM. Here's why. If you remove 3/4 of a turn to get the door to stay closed, and then if you open the door, it will get heavier as you open the door, and once open, the cables will come off the drums. This could create as much as a day's extra work. It could also cause door damage and/or result in serious injury. Do not use the door! Get different springs!
Most garage doors have two springs installed at the same time, when one breaks it's safe to say the second spring's life expectancy has just about expired. In order to save you from future inconvenience, unsafe garage door practices, and damaging your garage door opener, Precision will usually recommend to replace both springs. If you've had the same tires on your car for a while and one blows out while you're driving, wouldn't you replace them both? It's extremely important to properly maintain equipment such as garage doors and automobiles.

Start your garage door spring replacement project by getting a rough measurement of your springs (length and diameter). Then measure the width and height of your door. Make sure the quote includes the trip charge, parts and labor. Then ask for a price based on 7x19 lift cables and double-life springs. Those items will give you more years of service and should only add $65 to the price.

Garage Door Repair Guy Centennial Co


Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring.

Garage Door Repair Images Centennial Co


Replacement spring procedure took me exactly 1 hours including preparation and clean-up for double aluminum garage door. Watch the DIY video on Youtube, save $$, be careful with winding the torsion springs. Rule of thumb: 7' height door garage= 7' x 4 (each 1/4 turn) + 1 = 29 turns (1/4 turn), 8' height door garage = 8' x 4 + 1 = 33 turns (1/4 turn), and so on....

Automatic Garage Door Repair Centennial Colorado 80016


So your garage door is acting up, but you aren’t sure what the problem is. Maybe the door spring is one possible culprit, but you’re not sure if that’s actually the problem or if it’s something else. In this quick list, we’ll go through the most common broken garage door spring symptoms. If your garage door is exhibiting one or a few of these symptoms, there’s a good chance it’s broken and needs replacing.
Nothing can be more frustrating than trying to open or close your garage door, but have it get stuck halfway. The most common reason this happens is due to a broken torsion spring, a part that is responsible for providing balance. It is a common problem that has many people saying “My garage door has a broken spring or is stuck, what do I do next”? If you are in this same boat, you’ll find the information below very useful. https://www.youtube.com/watch?feature=youtube_gdata&v=Z_eZc-kh40c
If the door won’t move at all because of an alignment issue, then this problem isn’t one that you should try to tackle yourself. A garage door professional will have the necessary equipment needed to safely realign and repair your garage door. Additionally, if the track misalignment is beyond repair, a professional can install a new garage door track for you.
First, check to see if the transmitter on the wall inside your garage still opens your garage door when pressed. If it does, then the transmitter in your car likely just needs a simple battery replacement. If you have more than one car transmitter for your garage door, then your other transmitters will likely need new batteries soon as well, since they were probably installed around the same time.

Garage Door Repair Guy Centennial Co 80015


If you have decided to replace your springs, if you are sure your door had the correct springs, and if you are ready to buy new ones, we recommend that you measure your spring or springs following the instructions in Step 4 below. Measuring springs can be difficult; most individuals, even garage door technicians, sometimes have difficulty measuring torsion springs. Ordering incorrect springs wastes time and money.


10The type of garage door shown provides the necessary lift assistance with a “torque tube.” If you intend to use an opener, wait to install the tube. Otherwise, install the torque tube according to the manufacturer’s directions. Roll up the door about 4 feet to check for the alignment of the tracks, and make any adjustments. Then tighten all fasteners. 

Garage Door Repair Free Estimate Centennial Colorado


Repair Sagging Garage Doors – As doors and homes age, they can shift and move and sometimes this results in a garage door that needs to be realigned or reinforced. We will send a technician to your home to adjust the doors and to inspect the entire opening to make sure the door isn’t damaged. Once we understand the problem, we will fix the needed parts and make any adjustments to the door.

I have 2 full house humidifiers that have stopped functioning right. There are new filters, fan runs, tanks are full of water but they are not empting into the base. They have worked for part of the winter and now nothing seems to help...I loosened the caps thinking I had them too tight..... nothing seems to work .I have had humidifiers for 20 years and this is the first time this has happened to me. The humidifiers are only 2 years old. Any suggestions??
Weather conditions can make rails expand or contract slightly, which requires a little extra pressure from the opener to compensate. Turning the force-adjustment screw increases or decreases the force. However, adjusting the force is not something to play around with unless you are confident you know what you’re doing. The force adjustment signals the opener to stop and reverse when objects are detected in the closing path. Too little force and just about anything will trigger it to stop, but too much force and the garage door might not respond to resistance from something or someone in the path when the door is trying to close.
If you have a Wayne Dalton TorqueMaster system (pictured below), the springs will be inside a tube. The only way to determine if one is broken is to lift the garage door manually. If the door is heavy (roughly 60lbs for a double car door), you most likely have a broken spring inside the TorqueMaster tube. Another way to tell if you have a broken spring in your Wayne Dalton Torquemaster tube is if the door goes up and won't go back down. http://m.www.youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c
Spring Issues - Unless it is due to an obstruction of some type, uneven movement of your garage door is likely caused by a problem with the spring mechanism. Roll-up doors generally have one center-mounted torsion spring. The tension on torsion springs is great. Therefore, it is necessary to call a professional for any repairs to this type of spring mechanism to avoid serious injury. Because replacement of these springs or cables in a garage door can take at least two or three hours of labor, costs can average $300 or more.

Next, if you don’t find an obstruction, check the springs. If your door has torsion springs, which are horizontal at the top of the door, you can tell they are broken by checking for a gap between the two springs. If your door has extension springs, you can check by looking to see if they are hanging on the side of the door. If you have a broken spring, you’ll need to call a pro to replace it as this is a dangerous task.
"Mile High garage called shortly after submitting my request and set an appointment to have a repair man show up shortly after. They went over everything I needed to get done and gave me several pricing options to fix initial need and alleviate future issues. Work was done in a timely manner and customer service was great. Mile High garage called shortly after submitting my request and set an appointment to have a repair man show up shortly after. They went over everything I needed to get done and gave me several pricing options to fix initial need and alleviate future issues. Work was done in a timely manner and customer service was great. "

Garage Door Repair Guy Centennial Co 80016


Sometimes, people unplug their power source and then wonder why their garage door opener fails to work. Sounds ridiculous, I know, but it does happen. Make sure that your garage door opener is plugged into a working outlet. Outlets sometimes go out without warning, so you can check to see if the outlet is working by plugging another working electronic device into it. Also, check your circuit breaker, fuse, or GFCI.
If you use the correct tools and follow our instructions, you can rebuild the entire torsion spring system in just a few hours, without any side trips to the ER. We won't cover how to replace garage door extension spring systems in this story. But we'll show you garage door spring replacement on the more common torsion springs, the kind that mount on a bar above the garage door.

Garage Door Repair Free Estimate Centennial Colorado 80015


If the garage door is broken or damaged, it can affect the feeling of the entire house. It’s not only an inconvenience, but it can also make your entire house feel less sophisticated and less functional. If you happen to be trying to sell your house, this can seem like a major detraction. Even if you’re only having guests over, you may feel as though you’re doing less than putting your best foot forward by having a broken garage door.
First, check to see if the transmitter on the wall inside your garage still opens your garage door when pressed. If it does, then the transmitter in your car likely just needs a simple battery replacement. If you have more than one car transmitter for your garage door, then your other transmitters will likely need new batteries soon as well, since they were probably installed around the same time.

Every homeowner can relate to how life's inconveniences are thrown at you at the worst possible times. The last thing you want to happen is have your car stuck in the garage when you need it most, especially when it's only been a couple months, weeks, or even days after your last garage door repair! That's why Precision leads by example and follows the industry's best practices in order to make the best recommendation to homeowners each time we step foot in a garage. http://www.youtube.com/v/Z_eZc-kh40c
×