Torsion springs do not last forever, regardless of what some companies claim. “Lifetime” springs do not exist – all springs have a lifespan. Most builders typically install the lowest costing door available and with that generally comes lower cycle springs. A torsion spring’s life is determined by the number of cycles the spring is rated to last. Whenever the door goes up and down is what is referred to as a “cycle.” The springs that builders install can last as little as 7,500 cycles which means the average homeowner could get 3-5 years of life.
Changing your garage springs isn’t typically a DIY project and usually requires a professional. But it’s good to know when it’s time to find garage door spring replacements. To test your springs, disable your garage door opener if you have one, then raise the door manually. If it doesn’t stay in place on its own, it’s time to replace your garage springs.
Garage door springs come in two styles: torsion (see above), which mounts on the header above the door, and extension (Photo 1), which floats above the upper roller track. In the past, extension springs were safer to install but didn’t have containment cables running through the center of the spring. Without cable, these springs become dangerous, heavy whips when they break. They also tend to be noisier than torsion springs, and we recommend you use them only if you don’t have the 12 in. of headroom above the door that a torsion spring requires.

Garage Door Repair Companies Centennial 80016


Garage door springs can break for a variety of reasons. Extreme heat or cold, for instance, can stress the springs to the point of breaking, or it could be that normal wear on older springs could cause them to break. Whatever the situation, a broken spring can render your garage door inoperable. Your door will not be able to open or close when a spring is broken, and you should stand clear of your door until a professional can assess the situation and correct it.
Delivered on time, with the products described: springs, winding bats, & plastic bushing. Quick install, but apparently I measured wrong, so these total length I bought was larger (which is good as there is less stress on the spring). However this did mean that I needed more than the generic rule of 30 1/4-turns of preload. I wound up with 38 1/4-turns per side for the door to balance when open 3' (per familyhandyman.com recommendations). Would definitely do it again.

R-value describes the power of the insulation in your door. The higher the r-value, the stronger the insulation. Those doors will have better energy efficiency than doors that have a low r-value. Basic doors have an r-value of 0.0 with no insulation. The first step up gives you 1-3/8” insulation at a 6.5 rating. Next, a 1-3/8” thickness with Intellicore has a 12.9 r-value. The best option on the market is the 18.4 r-value, which has 2” Intellicore insulation.
With hundreds of moving parts that are all required to work together, it's no surprise that garage doors may need occasional repair and maintenance. Garage door repair services are also required in emergency situations, like when the garage door won't operate and the car is trapped inside or you've accidentally backed into the door when it was closed. Whether it's a specific repair of your garage door opener, a broken spring that needs to be replaced, or a bent or rusted track, The Home Depot's local, licensed service providers can get the job done quickly and efficiently.
If you need to leave the door open until you can make repairs, block the door track on both sides so the door can't move, and unplug the garage door opener (if you have one). If you want to close the door, you can try closing it with the opener, making sure there's nothing in the door's path in case something goes wrong. However, this will put some strain on the opener. Alternatively, you can have a few strong helpers hold the door while you disconnect it from the opener and carefully close the door manually—again, it will be very heavy.
For a scholarly introduction to torsion springs and for more information on how to install them I recommend you visit Richard Kinch's page, "How I Replaced Deadly Garage Door Torsion Springs and Lived to Tell the Tale." Richard is a brilliant engineer who has provided a wealth of technical information on fixing torsion springs along with valuable advice regarding some of the schemes unscrupulous garage door companies use to rip people off.
If you haven’t looked at garage doors lately, prepare to be pleasantly surprised. We’ve taken the garage door and made it stylish with designs to complement both classic and contemporary homes while still keeping the functionality you desire. A garage door can represent more than 30% of your home’s curb appeal, which makes choosing the right design especially important – and Home Depot has the widest selection available. With over 1,000 different garage door designs in wood, steel, composite, aluminum and glass, you’re sure to find the perfect style to transform your garage… and your home.
9.4 Slide the end of the shaft into the end bearing plate. Tighten the set screws an additional 1/4 to 1/2 turns beyond the point you finger-tightened them. Add an additional 1/4 turn if you could not find the original set screw indentations in the previous step. Heavier wooden garage doors may require an additional 1/4 turn. Caution: Under-tightening the drums could cause the drum to slip and the door to cock or fall. Over-tightening the set screws could damage the shaft or drum, resulting in the same problems. This is a critical step. http://youtube.com/watch?feature=youtube_gdata&v=Z_eZc-kh40c
When you're done watching this video you'll know how to determine whether the company you hired to replace your garage door spring installed the right size spring on your door. You'll also learn the consequences to your garage door opener if the wrong size spring is used. If you are having a problem with your garage door spring, the 2:30 minutes you spend watching this video is time will spent.
When it comes to installing garage doors and openers, The Home Depot has an unbeatable team of professionals dedicated to making sure your garage door project runs smoothly from start to finish. Your new garage door can be customized with a variety of features like unique color choices, window styles and hardware upgrades. We also offer options for your garage door opener including Smartphone control, Wi-Fi, battery back-up. The Home Depot installs garage doors and garage door openers with extended warranties that go beyond industry standards. Contact us today for a free in-home consultation.

6.13 Lower the second bar to the top of the garage door as you did the first bar. If your shaft is distorted inside the cone, you may need to tap the bar with a hammer as you unwind the spring. Maintain a firm grip on the bar; keep it firmly inserted completely into the cone; and be prepared at all times for the cone to slip, break, explode or snap loose from the shaft and jolt the bar down.

Automatic Garage Door Repair Centennial Co 80015


Garage door problems don’t have to mean the end of the world. Garage door repair is typically a one-day process and can be done for only a few hundred dollars. Common garage door repair requests include fixing slow or erratic garage doors, addressing strange sounds coming from the garage door or motor, fixing cosmetic damage such as dents or scrapes, repairing broken doors that are stuck open or closed, and troubleshooting inoperable doors.

"Mile High garage called shortly after submitting my request and set an appointment to have a repair man show up shortly after. They went over everything I needed to get done and gave me several pricing options to fix initial need and alleviate future issues. Work was done in a timely manner and customer service was great. Mile High garage called shortly after submitting my request and set an appointment to have a repair man show up shortly after. They went over everything I needed to get done and gave me several pricing options to fix initial need and alleviate future issues. Work was done in a timely manner and customer service was great. " http://m.youtube.com/embed/Z_eZc-kh40c
What LCD said is more or less right. Those are the ranges you'd typically find you will have to pay, but it's important to remember that the rates vary across the country. One thing I always advice others to do is to get quotes from different contractors. It might not be the biggest job, but you'd be surprised how much difference there typically is in the quoted prices. If you check out the link I put in the resource, it'll take you to a site where you can get quotes from 4 different contractors at once. Under "Select service" you simply pick "Spring Replacement".

Ace Garage Door Repair Centennial Colorado 80015


When a garage door service company gets a phone call in reference to a broken spring, the first thing the homeowner usually says is “the cables are broken”. This makes sense because the cables on a garage door will fly every which way, fall to the ground, become disconnected from the door, or even get caught in between the garage door and the jamb. It is rare for cables to break or need replacing when a garage door spring breaks. If your garage door has two torsion springs, the second spring will keep the cables tight and on the drums. You will have to look up at the springs to determine if one is broken.

Test the door balance. A garage door should require only a few pounds of pressure to move it up and down. If springs wear out and lose their resiliency, a power garage door opener may need to work extra hard to lift the door. This can quickly wear out the motor on the opener. Replacing worn-out springs is usually a job for a professional technician.

Surprisingly, your garage door just being locked can be causing your problem. Some garage doors have a “full lock” system which enables you, or anybody, to lock your garage door from the outside by only turning the handle. This could mean that anyone in your driveway (children, bystanders) could have turned your handle and mistakenly locked the garage door without you being aware of it. This is an easy fix by realizing this problem and then unlocking your garage door. rong.
A1 Garage Door Service is known for providing only the best value for money. We always aim for the best possible customer service and experience, reasonable costs for our products and services, give FREE estimates and FREE professional advice as well as amazing deals and discounts when you book our service. What’s more, we GUARANTEE that we service all manufacturer warranties, including lifetime warranties. What more can you ask for?
Your dream car is parked in out of the elements, but it's not secure because the garage door won't lock. Most garage doors have two horizontal bars that move out from the center of the door into slots along the side of the door in the door track, effectively locking the door in place. Over time, these bars can shift slightly out of position so that they are no longer correctly aligned with the locking slots. To realign the bars, unscrew the guide brackets on the edges of the door so that they are loose enough to move, and then reposition them so that they smoothly guide the locking bars into the locking slots. Lubricate the lock mechanism with machine oil and you're done.
• Extension springs: Garage door extension springs stretch to provide lifting power for the door. These springs are typically made of steel and mounted above the horizontal track of the garage door. A safety cable should run through your extension springs to prevent possible injuries or property damage. Extension springs are the most common type of garage door spring for residential use and can break after excessive usage.

Garage Door Repair Bracket Centennial Co 80015


While it would be wonderful if door springs lasted forever, the reality is that the simple act of opening and shutting the door multiple times every day isn’t easy. It’s hard on the springs, even though they’re built to do it. Most springs will last for a while, but they won’t last forever. The regular wear and tear of endlessly opening and shutting the door breaks them down and eventually, they’ll need to be replaced.

Garage Door Repair Free Estimate Centennial Co


An extension spring counterbalance system consists of a pair of stretched springs running parallel to the horizontal tracks. The springs lift the door through a system of pulleys and counterbalance cables running from the bottom corner brackets through the pulleys. When the door is raised, the springs contract, thus lifting the door as the tension is released. Typically these springs are made of 11 gauge galvanized steel, and the lengths of these springs are based on the height of the garage door in question. Their lifting weight capacity can best be identified by the color that is painted on the ends of the springs.
Snap a locking pliers onto the torsion tube to lock it into place while you tighten the drums. Rotate the drum to wind the cable into the winding grooves. Pull the cable as tight as possible before tightening the setscrews. Leave the locking pliers in place and repeat the tightening procedure on the other side. You want equal tension on both sides. Otherwise, the door will open unevenly.
One of the best ways to care for your springs is to check them over for wear. You can certainly look at them for damage, but sometimes the damage isn’t something that’s visible. In these cases, try lifting the garage door up from the ground. About halfway up, let go. If the door stays, the springs are still working perfectly. If the door sags or drops at all, this could be a sign that your springs are beginning to weaken and will need replacing soon.
Step 1: Check the metal tracks inside the garage. Look at the mounting brackets that hold the tracks to the walls. If they're loose, tighten the bolts or screws at the brackets. Working inside the garage with the garage door closed, examine the tracks for dents, crimps, or flat spots. If there are any damaged spots, pound them out with a rubber mallet, or with a hammer and a block of scrap wood. If the tracks are badly damaged, they should be replaced.
Install new or use this pair of left Install new or use this pair of left and right-wound torsion springs to replace broken sectional garage door torsion springs. All DURA-LIFT springs meet the DASMA standard rating of 10 000 plus door open and close cycles. Both the winding and stationary cones are professionally installed for safe operation. Winding ...  More + Product Details Close
Guest 9232954 -- check out the other answers for this question, and the links below the answers for even more - seems from $125-400 range from different contributors (should be replaced in pairs for balanced lifting unless one spring is quite new), about $200-250 or 300 seems a common charge. The springs themselves generally run about $20-50 each depending on lead they have to carry.
In order to prevent injury, garage doors automatically reverse if they come into contact with an obstacle. When the door closes halfway but then reverses for no apparent reason, this may be a sign that there is something preventing it from closing, something that you can't see. Check the tracks for stuff like dirt, rocks, bits of trash, or other debris. Give the tracks a wipe-down to dislodge anything that might be getting in the way.
The national average for garage door repair cost is between $80 and $110. Some of the factors that affect your garage door repair cost are the type of springs (most often torsion or extension), the size and weight of the door, and the door material. Many garage door pros will charge a service fee to visit your house and determine the problem. Often, the service fee includes a set amount of labor. One example of this is an $80 service fee that includes the first hour of work plus testing and inspecting your garage door and garage door opener, while another pro may charge $150 for the same standard service call.   
9.12 It is now time to secure the torsion springs in the middle. For various reasons, many installers will offset the center bracket several inches from the center of the door. Offsetting the bracket makes it easier to work around the opener bracket without causing any problems in the operation of your garage door, but offsetting the bracket is not necessary. If you have a slotted center bracket, remove the vise grip and lube the shaft where it turns inside the bushing. Position the shaft so it is the same distance from the header as it is at each end. The shaft should be straight and parallel to the header.
Sears Craftsman Garage Door Openers are America’s favorite. We have several options to choose from that will fit your individual needs. Sears garage door opener selections includes 1/2 horsepower, 3/4 horsepower, belt and chain drive as well as the Craftsman Smart Control garage door opener which allows you to control and monitor your garage door even when you are away from home. https://m.youtube.com/v/Z_eZc-kh40c
×