Torsion springs are located above the opening of your door with springs that slide onto a bar. Extension spring systems can be found alongside the opening of the door. It's important to know whether or not a garage door company provides service for your needs. Precision's professionally trained technicians are fully equipped to work on torsion and extension spring systems.

Garage Door Repair And Service Centennial Colorado 80015


Extension spring systems should always be restrained by a safety cable that runs through the middle of the spring, tying off to a solid point at the rear and front of the horizontal door track. Extension springs represent a hazard to bystanders when a spring, pulley, or cable breaks under tension. Metal parts from extension spring systems can suddenly be launched.

Garage Door Repair Centennial Colorado 80016


On average, to have your springs replaced on your garage door will vary anywhere from $200 to as much as $400 if you were to hire a professional.  Breaking the costs down, the springs, depending on the part needed and the size, will cost about $20 to $60 each.  Add in the labor, which can be $45 to $85 per hour, depending on your location, can bring the grand total to the estimate noted.   A tilt-up door, on average, will be about 20 to 30 percent less than a roll-up door.

Broken Arrow, Owasso, Claremore, Central Oklahoma, Sapulpa, New Tulsa, Jenks, Glenpool, Prattville, Sand Springs, Leonard, Coweta, Kiefer, Oakhurst, Inola, Fair Oaks, Verdigris, Lotsee, Sperry, Justice, Valley Park, Bixby, Mannford, Cleveland, Westport, Prue, Bethany, Yukon, Midwest City, Spencer, Newcastle, Harrah, Jones, Piedmont, Arcadia, Luther, Wellston, Dell City, Tuttle, Bridge Creek, Blanchard, Mustang, Noble, Goldsby
Replacing a garage door panel can add significantly to the cost of a garage door repair. Panels run horizontally on sectional roll-up garage doors. They may be made of wood, vinyl, aluminum, fiberglass or steel. Garage door panels can become damaged from hail and other extreme weather, dents and dings, car accidents, and age. When deciding if you want to replace a garage door panel, it’s helpful to compare the potential repair cost to the cost of a new garage door. Panel replacement requires a pro with the proper tools as well as the new parts. With parts and labor you could be paying more than $500 for one new panel. In comparison, a new garage door may cost $800-$1,200 (on average) with installation. If there is a possibility your garage door was structurally compromised when the panel was damaged, have the pro assess whether it’s better to completely remove and replace the door, rails and framework to ensure your home’s safety. It may also be better to completely replace your door if it is severely rusted or dented; if the paint is peeling and fading; if the door model is outdated or you can’t find replacement panels; or if the panels or rails are structurally compromised.

Garage Door Repair Installation Centennial Co 80015


If you have a steel door, but want the look of a wood one, it is not necessary to change your entire garage door. Often, it may be possible to mimic the look of wood with skillful painting. Your local home improvement store may be able to provide good advice about the type of paint and brushes needed to mimic the look of wood for your particular door material.
9.14 Slide the springs to the bracket. Double-check to make sure you have the right wound spring on the left side and the left wind spring on the right side. Turn the springs until the ends are facing you. The wire at the ends of both torsion springs here at the bracket should be pointing down. At the winding cones at the opposite ends, the spring wire points up. If not, reverse the springs. About once a month we get a phone call from a do-it-yourself customer who begins the conversation with, "I wound the garage door spring to about six turns and the spring came loose from the cone." We normally refer them back to this step and suggest they switch their springs.

Garage door springs offset the weight of a garage door and allow the door to be opened and closed easily, either by hand or by an automatic garage door opener. The high-tension steel in the springs has a limited lifespan, and over time, the springs lose their effectiveness. Garage door springs come in levels of quality—they may be described as "10,000-use" or "20,000-use" springs, for example. This may sound like a very large number, but when you consider that a garage door might be opened four or five times a day, every day, every year, it becomes clear that there is a limited lifespan for these critical garage door parts.

When it comes to installing garage doors and openers, The Home Depot has an unbeatable team of professionals dedicated to making sure your garage door project runs smoothly from start to finish. Your new garage door can be customized with a variety of features like unique color choices, window styles and hardware upgrades. We also offer options for your garage door opener including Smartphone control, Wi-Fi, battery back-up. The Home Depot installs garage doors and garage door openers with extended warranties that go beyond industry standards. Contact us today for a free in-home consultation.
9.9 Go to the other side of the garage door and insert the end of the cable into the drum. Rotate the drum until the cable is tight. Slide the drum against the bearing and push the shaft to the right. The marks should line up. If they don't, figure out why and correct the problem. It could be a stuck cable, the garage floor may have shifted, or the vertical angle that helps support the bearing plate may have loosened and shifted. Many garage doors have been installed with a gap between a drum and a bearing plate. The cable drums should always be flush against the race of the bearings.
Springs are one of the primary components in all garage door systems. Torsion springs are usually mounted horizontally over the door opening. As the door closes, cables add tension to the springs and as the door opens that tension is released. The opening of the door causes the springs to unwind in conjunction with the weight coming off the door. This achieves a natural buoyancy. However, as the door moves up and down over time and the cycle count rises, the steel in the torsion springs will grow weak and will no longer be able to create energy or lift your garage door.
A garage door spring replacement should cost between $175 and $225 for a single tension spring and between $250 and $300 for two tension springs. Most garage door companies carry a wide enough variety of spring sizes to cover most residential doors. As long as the proper amount of turns are put on the spring, there are more than one correct springs to use for any one door.
The Leading (scam) in the industry is the "LIFETIME WARRANTY". It sounds great when presented and seems fair and maybe even a good idea even though the initial cost seems pretty high (on average 450 - 700 dollars) what is not mentioned is the annual required cost (known as the required or annual door maintenance) to keep the warranty valid which if a standard 15,000 cycle spring/s is used should average Ten years, this annual service is usually 90 - 120 dollars. That would be another "900 - 1200" dollars invested in Ten years, that and the initial cost and you could buy two or more "complete new" doors in that time.
When a spring breaks on a garage door an immense amount of energy being displaced. Torsion springs are mounted over the garage door and they have a shaft running through the middle. When they break, the spring unwinds in less than a second and creates a loud noise due to the coils spinning on the shaft. Based on customer feedback, it can be quite startling.

When I called to schedule the repair service, I was transferrd 5 times and spoke with 6 service reps. Each rep was very confused by my request to get my garage door repaired. One rep actually told me that Sears doesn't repair garage doors. I had to tell her that Sears installed the door. When I finally found a rep who could schedule my service, it took one week for the appointment. https://www.youtube.com/watch?v=Z_eZc-kh40c&feature=youtube_gdata


Since garage doors come in all weights and sizes, the right springs need to be installed in order to properly balance the door. If a technician puts the wrong spring on your door, not only will this damage your garage door system, but it will cause the garage door opener to do more work than it was built to do. This is why Precision technicians only install the right springs for the door's weight and check their work by performing a balance test.

We look out for the safety of our customers and their families. That’s why we do not sell garage door torsion springs separately to consumers, and it’s also why we recommend putting your broken garage door in the hands of our experienced technicians. At Garage Door Medics, we are licensed, bonded, and insured. We have completed thousands of garage door installations and spring repairs, and we make sure they are done safely and with the right springs for your garage door system.


With every spring repair, Precision provides a free safety inspection to make sure all the hardware and moving parts on your door are in good working condition and meet safety standards. Since the hardware was probably installed at the same as the springs, it's possible there are worn mechanical parts on your door that are in an unsafe state. Think about spring failure as a symptom to a possibly larger problem with your door. This is why it's a Precision Best Practice to provide a free safety inspection and maintain a safe environment for our customers.

Garage Door Repair Centennial Colorado 80015


8.10 Double-check to make sure you have the correct wind on your new torsion spring. On the left side next to the winding cone the end of the spring wire should be pointing up if it is facing you. Notice, also, that the cone is red which usually designates right wind. Customers frequently call and explain that when they get about six turns on the springs they spin on the cones. This is due to installing the springs on the wrong sides of the center bracket.
Sears Craftsman Garage Door Openers are America’s favorite. We have several options to choose from that will fit your individual needs. Sears garage door opener selections includes 1/2 horsepower, 3/4 horsepower, belt and chain drive as well as the Craftsman Smart Control garage door opener which allows you to control and monitor your garage door even when you are away from home.
10.5 If the spring comes loose from the cone at about 6 turns, you are probably winding the spring backward because the springs are on the wrong sides. Switch the springs. Otherwise, after winding the torsion springs, you will need to stretch the springs and secure the winding cone. First, mark the shaft 1/4" beyond the winding cone with tape or with a file. We stretch the springs because the shaft floats horizontally between the flexible end bearing plates as the garage door operates. Although this may be as little as 1/4" the binding of the coils as the door closes often keeps the door from closing completely, especially when the springs and bearings are dry and need lubrication.
The low rating on the CS is due to the fact that inwas out of town and my wife called because the garage door wouldn't open. We had repairs to the only other exit, and the CS said because it could be opened manually, it was no emergency. She was stuck in the house for over Sixteen hours. No emergency crew came out. Steve, a tech who came out the first time, fixed the door. It is not his fault CS took their sweet time to help a 45 year customer. I commend Steve. I do NOT have anything good to say about CS. http://www.youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c
If your stuck garage door coincides with weather changes, you may need to adjust the pressure on the opener. Some openers have a force-adjustment mechanism that controls the force that's applied to operate the door. It's best to leave this adjustment to a garage door pro, as too much force may result in the door failing to stop when it should, posing a danger to people and objects in the door's path.
The low rating on the CS is due to the fact that inwas out of town and my wife called because the garage door wouldn't open. We had repairs to the only other exit, and the CS said because it could be opened manually, it was no emergency. She was stuck in the house for over Sixteen hours. No emergency crew came out. Steve, a tech who came out the first time, fixed the door. It is not his fault CS took their sweet time to help a 45 year customer. I commend Steve. I do NOT have anything good to say about CS.
Usually, when a garage door spring breaks the door has already closed or come down. In some instances, however, a spring can snap while the door is closing or in motion, causing the door to fall rapidly. In these situations, the door can become a safety concern for you and your family, so you should keep your distance and call a garage door professional as soon as possible. Garage doors are very heavy and can cause injury if not handled properly. When a garage door problem occurs, call a Sears Garage Door expert to help.
Jerrod the technician had answers to all my questions. He was very knowledgeable and very patiently explained what was going on with my garage door and the opener. I would definitely recommend A1 garage door service to friends and family. I was given options to either repair the door or replace it. I will get the door replaced when it gets non-functional from A1 garage door service. 

Garage Door Repair Companies Centennial Colorado 80015


We look out for the safety of our customers and their families. That’s why we do not sell garage door torsion springs separately to consumers, and it’s also why we recommend putting your broken garage door in the hands of our experienced technicians. At Garage Door Medics, we are licensed, bonded, and insured. We have completed thousands of garage door installations and spring repairs, and we make sure they are done safely and with the right springs for your garage door system.

A1 Garage Door Repair Centennial Colorado 80016


What LCD said is more or less right. Those are the ranges you'd typically find you will have to pay, but it's important to remember that the rates vary across the country. One thing I always advice others to do is to get quotes from different contractors. It might not be the biggest job, but you'd be surprised how much difference there typically is in the quoted prices. If you check out the link I put in the resource, it'll take you to a site where you can get quotes from 4 different contractors at once. Under "Select service" you simply pick "Spring Replacement".
Garage Door Spring, garage door houston, garage doors houston, houston garage door repair, garage door opener houston, garage door installation houston, garage door openers houston, garage door service houston, garage doors in houston, garage door repair in houston, garage door services houston texas tx, garage door torsion springs, Emergency Garage Door Repair
Spring Issues - Unless it is due to an obstruction of some type, uneven movement of your garage door is likely caused by a problem with the spring mechanism. Roll-up doors generally have one center-mounted torsion spring. The tension on torsion springs is great. Therefore, it is necessary to call a professional for any repairs to this type of spring mechanism to avoid serious injury. Because replacement of these springs or cables in a garage door can take at least two or three hours of labor, costs can average $300 or more.
Because your garage door is a major entryway to your home, it is important to keep it in good working order for your own safety, security, and convenience. Choosing the right style and appropriate materials will lessen the amount of repairs that may arise. Additionally, investing in regular maintenance can be cost-effective in the long run. If your garage door is in need of major repair, it is best to call a professional garage door repair company for assistance. Typically, the company will charge for at least one hour for making a service call. However, the benefits of a professional repair job can well outweigh any costs, as a professional can ensure the safety, security, and proper operation of your garage door.
10.5 If the spring comes loose from the cone at about 6 turns, you are probably winding the spring backward because the springs are on the wrong sides. Switch the springs. Otherwise, after winding the torsion springs, you will need to stretch the springs and secure the winding cone. First, mark the shaft 1/4" beyond the winding cone with tape or with a file. We stretch the springs because the shaft floats horizontally between the flexible end bearing plates as the garage door operates. Although this may be as little as 1/4" the binding of the coils as the door closes often keeps the door from closing completely, especially when the springs and bearings are dry and need lubrication.

When it comes to garage doors, functionality and safety are equally important in the eyes of Sears Garage Door technicians. Our associates know the importance of garage door safety and the hazards that a faulty garage door can pose for your family. To confirm that your garage door and opener operate safely, our technicians perform a 20-point safety check during maintenance calls and repair jobs. This safety check verifies that any repair work performed has been done correctly and that there are no lingering safety problems with your door and mechanisms. If our technician discovers any safety concerns, he’ll advise you on the best way to proceed with correcting the problem.

Automatic Garage Door Repair Centennial Co 80016


Our technicians are specially trained to handle a variety of garage brands, styles, and configurations. After arriving at your home, a Sears technician will diagnose the problem and walk you through the options for fixing it. Next, the technician will make any necessary adjustments or replace broken parts to ensure the door can be operational once again. We always attempt to complete repairs the same day of service, and your satisfaction is guaranteed. Our representatives are standing by for your call and are happy discuss pricing options. http://www.youtube.com/watch?v=Z_eZc-kh40c&feature=youtu.be


Once the springs break, quite a bit of tension is put on the door cables, and they will often break next. When these cables break, they will snap and forcibly fly out like a broken rubber band. Think about how much it hurts to be snapped by a broken rubber band, and then multiply it by a hundred to account for the size and weight of the garage door cables.
Torsion springs do not last forever, regardless of what some companies claim. “Lifetime” springs do not exist – all springs have a lifespan. Most builders typically install the lowest costing door available and with that generally comes lower cycle springs. A torsion spring’s life is determined by the number of cycles the spring is rated to last. Whenever the door goes up and down is what is referred to as a “cycle.” The springs that builders install can last as little as 7,500 cycles which means the average homeowner could get 3-5 years of life. http://y2u.be/Z_eZc-kh40c
×