If you notice that the garage door opens normally but doesn’t make any attempt to close when the remote is pressed, the first thing you’ll want to do is visually inspect the photo eyes. Over time, these eyes can get dirty, causing the light from the beam to be blocked. They also can eventually become misaligned, causing the eyes to not match up on both sides.
One thing to consider - assuming you have 2 springs and an opener, unless the other spring is quite new, you should replace it at the same time, first because it will probably break fairly soon anyway and changing two is only about $50 more than changing one, and because the springs on both sides should be of equal stiffness - if not, then the door will be unevenly weight compensated and try to open cockeyed, increasing wear and risk of damaging the motor.
A garage door spring replacement should cost between $175 and $225 for a single tension spring and between $250 and $300 for two tension springs. Most garage door companies carry a wide enough variety of spring sizes to cover most residential doors. As long as the proper amount of turns are put on the spring, there are more than one correct springs to use for any one door. 

Garage Door Repair Free Quote Centennial Colorado 80015


For a scholarly introduction to torsion springs and for more information on how to install them I recommend you visit Richard Kinch's page, "How I Replaced Deadly Garage Door Torsion Springs and Lived to Tell the Tale." Richard is a brilliant engineer who has provided a wealth of technical information on fixing torsion springs along with valuable advice regarding some of the schemes unscrupulous garage door companies use to rip people off.
6.13 Lower the second bar to the top of the garage door as you did the first bar. If your shaft is distorted inside the cone, you may need to tap the bar with a hammer as you unwind the spring. Maintain a firm grip on the bar; keep it firmly inserted completely into the cone; and be prepared at all times for the cone to slip, break, explode or snap loose from the shaft and jolt the bar down.
Containment cables. When old extension springs break, the springs and cables become heavy whips that damage cars and even injure people. To solve the whipping problem, manufacturers now offer containment cables that run through the center of side-mounted extension springs. If you have extension springs and don’t plan to replace your door, make sure the springs have these containment cables, or have a professional install them.
On our EZ-Set Torsion Springs page you will find several options for replacing these springs. We also have step by step instructions for EZ-Set Torsion Spring Replacement. In addition, one of our customers has provided excellent EZ-Set Torsion System instructions for removing the spring without wrecking the winding unit that secures the stationary cone. Instead of a spanner tool, you may prefer to use a pipe wrench or large channel locks to hook the end of the spring and remove it from the cones in the last step.
Guest 9232954 -- check out the other answers for this question, and the links below the answers for even more - seems from $125-400 range from different contributors (should be replaced in pairs for balanced lifting unless one spring is quite new), about $200-250 or 300 seems a common charge. The springs themselves generally run about $20-50 each depending on lead they have to carry.

Affordable Garage Door Repair Centennial Co 80016


When you know you’re in range and the door still won’t open, check to make sure the antenna is hanging down from the motor inside your garage and nothing is blocking it. Your antenna must be free from any obstruction to clearly receive the signal to open and close the door. Also inspect the antenna for any signs of damage. If it looks like there has been damage to the antenna, you’ll need to call your garage door technician to come out and replace it.
10.7 Continue tapping until the cone moves out to the mark on the shaft. Continue holding the bar off the garage door and pulling back toward the center of the door. If the cone slips away from the mark, repeat this step. Keep an eye on the tape to make sure the bar doesn't slip out of the cone. If it does start to slip, rest the bar against the top of the garage door, insert a bar in the next hole and turn the cone up enough to make it possible for you to push the marked bar back into place.
Chris was very professional & thorough. He arrived on time & was able to answer all questions that I had. I was extremely satisfied with the quality of the work he performed. I spoke several times on the phone with Mrs. Carol who keep me informed prior to, during, and after the installation of my garage door. She was very professional, easy to talk with and resolved any misunderstanding that I had.
9.14 Slide the springs to the bracket. Double-check to make sure you have the right wound spring on the left side and the left wind spring on the right side. Turn the springs until the ends are facing you. The wire at the ends of both torsion springs here at the bracket should be pointing down. At the winding cones at the opposite ends, the spring wire points up. If not, reverse the springs. About once a month we get a phone call from a do-it-yourself customer who begins the conversation with, "I wound the garage door spring to about six turns and the spring came loose from the cone." We normally refer them back to this step and suggest they switch their springs.
The following instructions for replacing garage door springs are for do-it-yourself homeowners and for maintenance repair men who service their smaller commercial or industrial sectional overhead doors. These directions are designed for torsion springs mounted to both sides of an anchor bracket above the middle of the garage door as pictured above. Instructions for replacing a single torsion spring, for replacing garage door extension springs, and for replacing Wayne Dalton Torquemaster springs are linked to our DIY Instructions page above. You'll also find a link for any other garage door parts you may need while repairing your door.
No matter what kind of door you are installing, be very careful. The instructions that follow are merely guidelines. You should read your garage door manufacturer's instructions and owner's manual very carefully before attempting either type of installation. And if you're a do-it-yourself greenhorn, skip this project and hire an experienced professional. It may be more expensive, but garage door installation is on the higher scale of DIY difficulty.
6.10 If the garage door comes off the floor when you pull down on the bar, and if the cone still won't loosen, tap the bar next to the cone with a hammer to force the cone beyond the swollen portion of shaft. Maintain a firm grip on the bar; keep it firmly inserted completely into the cone; and be prepared at all times for the cone to slip, break, explode or break free from the shaft and yank the bar down.
Garage doors cause injury and property damage (including expensive damage to the door itself) in several different ways. The most common causes of injury from garage door systems include falling doors, pinch points, improperly adjusted opener force settings and safety eyes, attempts at do-it-yourself repair without the proper knowledge or tools, and uncontrolled release of spring tension (on extension spring systems).

Garage Door Repair Installation Centennial Colorado 80016


After you’ve ordered your new garage door, we’ll perform a site inspection to confirm your door size. We’ll contact you to schedule the installation, and our professional installers will do the rest. They’ll deliver your door, take down the old door, reconnect your opener if there is one, seal your perimeter and provide a final walk-through where they’ll clean up the area and haul away your old door. Additional fees for haul away may apply in some markets. We are happy to provide answers to questions you may have at the time of your garage door and opener installation. 

Garage Door Repair Estimates Centennial 80015


It is very important that the replacement springs are calibrated for the weight of your door. Using the wrong size garage door springs will caused the to not function properly and could also cause the opener to break much quicker. Replacing extension springs can be very dangerous and if done wrong can harm someone using the garage door. Make sure you call the Garage Door Doctor to ensure your garage is repaired properly!

Garage Door Repair Companies Centennial Co


Every thing the tech demostrated was helpful, he knew how to do his job even if his eyes were shut. Very knowledgeable, took time out to explain every detail about the install process. Very highly satisfied. A d would love to have him for future additional repairs. Would definitely recommend sears and would use you guys again thanks mr.technician for a job well done.
Sears offers two different drive mechanisms to accommodate your home and budget. If you're looking for a smooth and quiet opener for a garage door with rooms located above the garage or attached to the garage, the belt drive is going to be the best for you. You can also choose a chain drive opener, which is perfect for garages that are unattached to the home.
Garage door and their openers require basic maintenance. If an emergency occurs, you need to know that your door will open and close. Especially if you have children at home, check the sensors once a month to prevent potential injury. The force setting test lets you know that the door will stop if a child or object is in the way. The photo eye sensors will detect if a child or object is moving under the door and prevent the door from closing. In addition, a complete visual inspection of the system will help to show if something looks out of place or there is obvious damage. Lubricate your springs semi-annually. Investing a few minutes to keep your garage door in tip-top shape may prevent it from getting stuck halfway open or closed.
If a roll-up door, assuming you have not put in cabinets or anything that prohibits sliding the shaft sideways about 2-3 feet out of the spring to change it, then about $200-250 should do it for a 2-car garage door. If he has to disassemble the brackets to remove the springs because the shaft cannot slide sideways enough to get the springs on/off, then probably another $50-100.
The Leading (scam) in the industry is the "LIFETIME WARRANTY". It sounds great when presented and seems fair and maybe even a good idea even though the initial cost seems pretty high (on average 450 - 700 dollars) what is not mentioned is the annual required cost (known as the required or annual door maintenance) to keep the warranty valid which if a standard 15,000 cycle spring/s is used should average Ten years, this annual service is usually 90 - 120 dollars. That would be another "900 - 1200" dollars invested in Ten years, that and the initial cost and you could buy two or more "complete new" doors in that time.

The winding and unwinding is done at a metal fitting, called a winding cone, attached to the outside end of the spring. You stick a winding bar into one of the four holes in the cone and use the bar as a lever to turn the cone. Once you've completed a quarter turn, insert the other bar into a different hole in the cone and let the bar lever against the closed garage door to hold the spring tension. This allows you to move the original bar to repeat the process, alternating the bars with each quarter-turn. It takes about 30 quarter-turns to fully tension a standard torsion spring.

Affordable Garage Door Repair Centennial Colorado 80016


If you’ve tested and tried to remedy these other problems and you’re still having issues, you may need to reprogram your transmitter. All transmitters have a learn button somewhere on the remote, so first you’ll need to locate that on your transmitter. Press and hold the learn button for a few seconds until the indicator light starts blinking. While the light is blinking, press your remote button again to reprogram that remote.

Determine the inside diameter of the spring and the size of the coils. Run a tape measure across the opening at one end of the spring. Carefully measure the inside diameter of the spring so you can provide the supplier with this information. Then, use a tape measure to find the length of 10 coils on the spring. Divide the length by 10 to determine the measurement of a single coil.[7]
As commercial and residential garage door service professionals, we’ve pretty much dealt with every issue you can think of when it comes to garage door repair. Even still, there are sometimes issues that continue to surprise us, like the tiny insect nest growing on the photo eye sensor or the tennis ball that somehow managed to knock the door entirely off its track. Even though these issues are uncommon, it’s nothing that garage door service professionals like us can’t handle!

Many jobs around the house are fairly easy fixes. It’s relatively easy to clean out your fireplace, clean the leaves from the gutters or repaint a wall. It’s a different thing to replace your garage door spring. It’s careful work that is almost impossible to do correctly the first time. Garage door professionals spend a great deal of time learning how to do it properly, and even the most detailed instructions won’t make you an expert in the span of a few hours. It can be almost infuriatingly annoying at times and is simply better left to professionals.
Garage door springs support most of the weight of the door when it's opening and closing. A broken spring typically will make the door very hard to lift, rather than causing the door to stick halfway. But some spring problems can contribute to a stuck door. The springs help turn metal wheels, called pulleys, that help lift the door via vertical cables at each side of the door. A pulley can become jammed by an obstruction or possibly a misaligned or hung-up cable. Any problems with springs or pulley should be examined by a garage door professional. Springs (and pulleys) are highly tensioned and can be very dangerous to work with.

For example, low headroom garage doors often have cable drums on the outside of the end plate and the torsion springs usually wind down rather than up. They normally have left wind springs mounted on the left side of the spring anchor bracket and right wind springs mounted on the right side of the bracket. The first part on the shaft beyond each torsion spring is the end bearing plate. Just beyond the end bearing plate is the cable drum. On these the cable often runs on the front of the cable drum. The bottom of the cable is attached to a bracket that wraps around the front of and outside the vertical track.
The most common question we get over the phone is, "Okay, so how much does it cost to replace garage door springs?" To give you an exact price quote, we would need to know the size of the door, weight, and type of garage door springs needed (torsion or extension). Since we carry over 30 different types of springs to account for all the different types of garage doors, we recommend that a professionally trained technician takes the proper measurements himself before giving you an exact price quote.

Instead, try other methods that might break the frozen connection between the door and the floor. For example, you can use a heat gun or hair dryer to melt the ice and free the door. Standard de-icing products can also work. And if you are careful not to damage the door or the seal on the bottom of the door, you can use a flat shovel or similar tool to chip away at the ice.

Garage Door Repair Emergency Centennial Colorado 80015


Step 5: Check for loose hardware, and tighten as needed. On swing-up doors, check the plates where the spring is mounted to be sure the screws are tight, and tighten any loose screws. On roll-up doors, check the hinges that hold the sections of the door together; tighten any loose screws, and replace any damaged hinges. Sagging at one side of the door can often be corrected by servicing the hinges. If a screw hole is enlarged, replace the screw with a longer one of the same diameter, and use a hollow fiber plug, dipped in carpenters' glue, with the new screw. If the wood is cracked at a hinge, remove the hinge and fill the cracks and the screw holes with wood filler. Let the filler dry and then replace the hinge. If possible, move the hinge onto solid wood.

Mechanical garage door openers can pull or push a garage door with enough force to injure or kill people and pets if they become trapped. All modern openers are equipped with “force settings” that make the door reverse if it encounters too much resistance while closing or opening. Any garage door opener sold in the United States after 1992 requires safety eyes—sensors that prevent the door from closing if obstructed. Force settings should cause a door to stop or reverse on encountering more than approximately 20 lbs (9.07 kg) of resistance. Safety eyes should be installed a maximum of six inches above the ground. Many garage door injuries, and nearly all garage door related property damage, can be avoided by following these precautions.
For commercial or residential doors, operators and accessories outside of the U.S. or Canada you can contact international. ​​​​​​Please be sure to include the following in your e-mail, so we can connect you with the Overhead Door™ Distributor that can best serve you: Contact Person, Phone Number (including local dialing code), Company Name, City and Country, Product(s) of interest (i.e. residential or commercial garage doors, operators and accessories), Name of Project (if any) and Project Specifications.​​​​​​​​​​​​ 

Abc Garage Door Repair Centennial 80016


If you happen to be home when these break, you’ll hear a loud bang from inside your garage. This bang can be so loud that some people might think a firecracker went off inside their garage. That’s because garage doors can be very heavy and despite what most people think, it’s not the garage door opener that does the heavy lifting, but rather the heavy-duty springs of the door.

Replacing torsion springs is done with the door closed. You start by carefully unloading all of the springs (most standard-size doors have two; any broken spring will already be unloaded), using the winding bars. Then, you unbolt the springs from the central rod bracket, disconnect the cables from the pulleys, and loosen the pulleys and slide them off of the rod. Next, you swap out the springs, reinstall the pulleys and cables, and secure the inside ends of the springs to the central bracket. Finally, you wind up both springs (securing them with two setscrew bolts on the winding cones) and test the door for proper spring tension. Often, springs need an extra quarter-turn or two to get the door balance just right.

Garage Door Repair Companies Centennial Colorado 80016


Most garage doors from the past 15-20 years have a photo eye which detects if a person or object is blocking the door from lowering all the way. The photo eye will be about 4-6 inches off of the ground for most doors, with an eye that is about the size of a pea. It shoots a laser across the length of the garage that, if interrupted, will cut off the signal used to lower and raise the door.
The Leading (scam) in the industry is the "LIFETIME WARRANTY". It sounds great when presented and seems fair and maybe even a good idea even though the initial cost seems pretty high (on average 450 - 700 dollars) what is not mentioned is the annual required cost (known as the required or annual door maintenance) to keep the warranty valid which if a standard 15,000 cycle spring/s is used should average Ten years, this annual service is usually 90 - 120 dollars. That would be another "900 - 1200" dollars invested in Ten years, that and the initial cost and you could buy two or more "complete new" doors in that time.
6.13 Lower the second bar to the top of the garage door as you did the first bar. If your shaft is distorted inside the cone, you may need to tap the bar with a hammer as you unwind the spring. Maintain a firm grip on the bar; keep it firmly inserted completely into the cone; and be prepared at all times for the cone to slip, break, explode or snap loose from the shaft and jolt the bar down.
I really think that bill was way to much.I had I stalled new door springs with the help of a friend but tube door didn't. want to open .that's why I called sears so the man that came to my house spent about 15 minutes working all that be did was remove the new springs saying they were the wrong springs and put the old springs back on that's all he did .

When a torsion spring is wound up, it grows 2” in length. This is because the spring starts to compress and the metal has to go somewhere. After the spring is wound, the winding cone is clamped down on the torsion shaft so it can turn the drums to wind the cables as the door goes up. Since the end of the spring is “set” on the shaft, a two-inch gap is left when the spring break's. This is the most definite way of determining you have a broken garage door spring.

Garage Door Repair Near Me Centennial Colorado


DoItYourself.com®, founded in 1995, is the leading independent home improvement and repair website. We welcome your comments and suggestions. All information is provided "AS IS." Website operating problems contact [email protected] Questions of a Do It Yourself nature should be submitted to our "DoItYourself.com Community Forums". Copyright© 1995-2018 MH Sub I, LLC dba Internet Brands. All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use. View our Privacy Policy here.
Slide the left spring onto the tube and add the cable drum. When your new springs arrive, put the new left spring (the 1 with the end facing up and to the left) on the torsion tube, making sure that the stationary cone on the end of the spring faces the center bracket. After sliding the new spring into place, replace the cable drum and insert the torsion bar into the left bearing bracket.[9]

Garage Door Repair Estimates Centennial Co


2.3 Beware of older winding cones. These older Crawford and McKee torsion spring cones were made for 5/8" bars. Sometimes, however, the holes are too small for 5/8" bars. Whatever you do, don't use a 1/2" bar; instead, grind down a 5/8" bar to fit. I recently had a McKee spring let loose after winding because I used a 1/2" bar when my 5/8" bar wouldn't fit. Just before it let loose I was telling myself, "This is not safe." And it wasn't. The only safe way to replace these older springs is to make a winding bar for each hole of each cone.

Garage Door Repair Emergency Centennial 80016


Home Depot local Service Providers are background checked, insured, licensed and/or registered. License or registration numbers held by or on behalf of Home Depot U.S.A., Inc. are available at homedepot.com/licensenumbers or at the Special Services Desk in The Home Depot store. State specific licensing information includes: AL 51289, 1924; AK 25084; AZ ROC252435, ROC092581; AR 228160518; CA 602331; CT HIC.533772; DC 420214000109, 410517000372; FL CRC046858, CGC1514813; GA RBCO005730, GCCO005540; HI CT-22120; ID RCE-19683; IA C091302; LA 43960, 557308, 883162; MD 85434, 42144; MA 112785, CS-107774; MI 2101089942, 2102119069; MN BC147263; MS 22222-MC; MT 37730; NE 26085; NV 38686; NJ 13VH09277500; NM 86302; NC 31521; ND 29073; OR 95843; The Home Depot U.S.A., Inc. is a Registered General Contractor in Rhode Island and its Registration Number is 9480; SC GLG110120; TN 47781; UT 286936-5501; VA 2705-068841; WA HOMED088RH; WV WV036104; WI 1046796.
There are many steps to replacing torsion springs, but overall it's a simple, straightforward process. If you're inclined to attempt it, find a good online video tutorial (preferably done by a garage door pro) that walks you through the entire process, including how to buy the right size of springs. You can also buy new springs and any related parts online, along with the most important items that you need: the two solid-metal winding rods that you use to wind and unwind the torsion springs.
Quite a few garage doors come with manual locks, especially older models, for added security for your house. These typically look like a knob or handle in the middle of your door with two bars running horizontally from each side. There may be a small button on the top or side of the handle that you can press to slide the bars across the doors, thus locking the garage door from the inside. It can be somewhat easy to accidentally hit that button, especially if you’re getting large objects out of the trunk of your car near the door.
10.7 Continue tapping until the cone moves out to the mark on the shaft. Continue holding the bar off the garage door and pulling back toward the center of the door. If the cone slips away from the mark, repeat this step. Keep an eye on the tape to make sure the bar doesn't slip out of the cone. If it does start to slip, rest the bar against the top of the garage door, insert a bar in the next hole and turn the cone up enough to make it possible for you to push the marked bar back into place.
The garage door opens and closes many times throughout the year, and something may blow inside. While it is usually something such as loose leaves or small amounts of dirt, the rails that the door travel along can collect this loose debris. Over time, the buildup of debris creates a blockage on the rails. Note where on the rails the door is stuck and clean that area. If children use the garage to leave the house, it's sometimes something as simple as a small, bouncing ball that happens to land in just the right -- or wrong -- spot. https://www.youtube.com/watch?v=Z_eZc-kh40c&hc_location=ufi

Usually, when a garage door spring breaks the door has already closed or come down. In some instances, however, a spring can snap while the door is closing or in motion, causing the door to fall rapidly. In these situations, the door can become a safety concern for you and your family, so you should keep your distance and call a garage door professional as soon as possible. Garage doors are very heavy and can cause injury if not handled properly. When a garage door problem occurs, call a Sears Garage Door expert to help.


The average lifespan of torsion springs is determined by its cycle count. Garage Door Medics provides springs with an average of 25,000 cycles and we can provide custom size springs for any door. The industry standard is 10,000 cycles. When a garage door is used more frequently, the springs may not last as long. If you begin to see signs of wear, it’s time to give Garage Door Medics a call!


10.4 Raise the second bar 90 degrees and insert the first bar. This is "three." Continue winding. If the spring shortens in length, unwind the spring and switch sides - the springs are on backward. Otherwise, continue winding until you reach a count of "30." This is 7 1/2 turns, which is normal for most 7' doors. Longer life springs are wound the same number of turns. Newer steel doors with only one strut on top often need only 7 1/4 turns. On 8' doors count to 34. Each time you insert a bar into the winding cone, listen for the click to let you know the bar is in all the way. Not inserting the bar all the way could cause the cone to explode.
Once the springs break, quite a bit of tension is put on the door cables, and they will often break next. When these cables break, they will snap and forcibly fly out like a broken rubber band. Think about how much it hurts to be snapped by a broken rubber band, and then multiply it by a hundred to account for the size and weight of the garage door cables. https://www.youtube.com/e/Z_eZc-kh40c
×