8.10 Double-check to make sure you have the correct wind on your new torsion spring. On the left side next to the winding cone the end of the spring wire should be pointing up if it is facing you. Notice, also, that the cone is red which usually designates right wind. Customers frequently call and explain that when they get about six turns on the springs they spin on the cones. This is due to installing the springs on the wrong sides of the center bracket.
If your garage door goes up and down in a jerky motion, you might have one broken spring on a two spring system. Some garage door openers are strong enough to lift a door with only one good spring. The “herky jerky” motion is especially common with garage doors equipped with extension springs. It might be something as simple as lubricating your garage door pulleys, hinges, and rollers. When in doubt or if something doesn’t feel right about your door, call a service company to have it serviced.
Replacing a garage door panel can add significantly to the cost of a garage door repair. Panels run horizontally on sectional roll-up garage doors. They may be made of wood, vinyl, aluminum, fiberglass or steel. Garage door panels can become damaged from hail and other extreme weather, dents and dings, car accidents, and age. When deciding if you want to replace a garage door panel, it’s helpful to compare the potential repair cost to the cost of a new garage door. Panel replacement requires a pro with the proper tools as well as the new parts. With parts and labor you could be paying more than $500 for one new panel. In comparison, a new garage door may cost $800-$1,200 (on average) with installation. If there is a possibility your garage door was structurally compromised when the panel was damaged, have the pro assess whether it’s better to completely remove and replace the door, rails and framework to ensure your home’s safety. It may also be better to completely replace your door if it is severely rusted or dented; if the paint is peeling and fading; if the door model is outdated or you can’t find replacement panels; or if the panels or rails are structurally compromised.

Garage Door Repair Installation Centennial Co 80015


Both types of springs are loaded, or under tension, when the door is closed. This gives them stored energy to help lift the door as it's being opened. When the door is all the way up, the springs are relaxed, or relatively so—they still may be under some tension. The mechanical difference between extension and torsion springs is that extension springs are loaded by stretching, or elongating, while torsion springs are loaded by twisting, creating torque.

The winding and unwinding is done at a metal fitting, called a winding cone, attached to the outside end of the spring. You stick a winding bar into one of the four holes in the cone and use the bar as a lever to turn the cone. Once you've completed a quarter turn, insert the other bar into a different hole in the cone and let the bar lever against the closed garage door to hold the spring tension. This allows you to move the original bar to repeat the process, alternating the bars with each quarter-turn. It takes about 30 quarter-turns to fully tension a standard torsion spring.

Affordable Garage Door Repair Centennial Colorado 80016


Vincent was professional, informative, personable, efficient, and cleaned up his work area as he worked. I told him and now I am telling you... He my "Jordan" of garages. Give him a raise or at least a bonus. Thank you for sending him for my install. I am extremely pleased with my garage opener & with his install and information I am confident in its operation. Thank you.
Most garage doors have two springs installed at the same time, when one breaks it's safe to say the second spring's life expectancy has just about expired. In order to save you from future inconvenience, unsafe garage door practices, and damaging your garage door opener, Precision will usually recommend to replace both springs. If you've had the same tires on your car for a while and one blows out while you're driving, wouldn't you replace them both? It's extremely important to properly maintain equipment such as garage doors and automobiles.
How much should a garage door spring replacement cost? The national average is between $200 and $300 for a professional to come to your house and replace two springs. On line sources suggest a higher price of over $700 and that you will save $500 or more by replacing springs yourself. This is simply not true. To find the cost for replacing springs in your area look for a reputable company through Yelp or the Better Busienss Bureau. If clicking a site's BBB logo doesn't take you to the BBB site, we advise purchasing your springs from a different company.
If your photo eyes are clean and the door still isn’t closing, the next thing you’ll need to do is check the alignment of the eyes. The eyes should be pointing in exactly the same direction and at the same angle. If they’re off, they won’t register that the other one is there, and it’ll assume something is in its path, causing the door to stay in the open position. When checking the alignment, measure the height of each photo eye from the ground. Use a level to make sure they’re pointing directly across at each other at the same angle. A laser level will make this part a little easier, but if you don’t have one, a regular level will work as well.
Most residential garage doors have one of two types of springs: torsion or extension. Torsion springs are heavy-duty springs mounted to a metal rod that runs parallel to the door, directly above the door opening. These springs are loaded, or tensioned, with a twisting action. When the door closes, cables attached to the bottom corners of the door pull on pulleys attached to the ends of the metal rod the springs are mounted on. The pulleys turn the rod, which twists the springs and creates tension. When the door is opened, the springs unwind and help lift the door.
Through our garage door configurator by Clopay, you can design, visualize and purchase a new Clopay garage door. Upload a photo of your home and then browse the configurator to see which style works for you. Choose from a variety of designs, textures, colors, finishes, window options and decorative hardware. You’re able to easily and quickly see the transformation, and then make it a reality.
When it comes to installing garage doors and openers, The Home Depot has an unbeatable team of professionals dedicated to making sure your garage door project runs smoothly from start to finish. Your new garage door can be customized with a variety of features like unique color choices, window styles and hardware upgrades. We also offer options for your garage door opener including Smartphone control, Wi-Fi, battery back-up. The Home Depot installs garage doors and garage door openers with extended warranties that go beyond industry standards. Contact us today for a free in-home consultation.
Go for the look of wood with less upkeep with low-maintenance faux wood composite & steel garage doors from our Canyon Ridge® & Coachman® Collections. Our Gallery, and Classic Collection garage doors are also available with Ultra-Grain®, a wood look durable paint. If you’re looking for a more traditional look, our Classic™ Collection of steel raised panel and flush panel garage doors complement most home styles. Add one of our many decorative window options to customize the door's appearance and let natural light into your garage.
Thread the cables and tighten the drums. Run the lift cable between the roller and the doorjamb. Slip the lift cable stop through the cable slot on the drum. Then, attach locking pliers to the torsion tube to secure it in place. Spin the drum to wind the cable into the grooves, then tighten the set screws. Repeat on the other side, leaving the locking pliers in place.[11]
SNAP... bang... boom. That is the sound of a garage door torsion spring breaking. It can be a very loud noise that sounds like a firecracker or gunshot. Springs are rated for a certain number of cycles and are the first thing that will break in your garage door assembly. Broken springs are the #1 source of customer calls for garage door repair companies. If you have a broken spring, you should NEVER try to open the door, as it can be very dangerous. This repair should be left to a professional or someone with the right tools and skills.

You can choose from three basic types of steel door: (1) steel only; (2) steel with insulation on the inside; and (3) steel on both sides with 1-3/8 to 2 in. of insulation. Other features that add to the cost are thicker insulation and windows, especially insulated windows. The do-it-yourself tensioning systems also add a little to the door’s cost. Be sure to specify exactly what you want.

Check your garage door rollers to see if they have come off their tracks. If no damage has been done, a tech should be able to easily place them back on. If the track has become bent, however, it must be repaired and possibly (depending on the amount of damage) replaced. Don’t operate your door if it's off track or your track is bent. Your door could become seriously damaged.
4. It is also important to note that extension springs sometimes do not break but rather ‘stretch out’. This is easy to spot as the space between coils when the door is closed is normally consistent. When the spring fails without breaking the space between the coils will become very inconsistent. This condition is quite visible and if it exists the springs should be replaced (Know when to call quits with your garage door). 
These instructions were first posted in 2005, and they were updated in August of 2008. I have been frank about the hazards of garage door repairs and about my own accidents incurred while replacing torsion springs. For what it's worth, you might be surprised to know that I, too, have benefitted from producing these instructions. I have not had any garage door accidents since we first published these on the web in 2005. And, in as much as I have helped keep other DIY-ers out of the emergency room, I consider myself somewhat of a medical practitioner.

On one-piece doors with side springs, you open the door to relieve the spring tension, and simply swap out the springs on the opener-arm mechanism; there are no cables or pulleys to deal with, and the springs have internal safety rods. Some doors have tensioners that maintain moderate tension when the door is open all the way, and on these you'll have to loosen the tensioner in order to remove the spring.


Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.
9.14 Slide the springs to the bracket. Double-check to make sure you have the right wound spring on the left side and the left wind spring on the right side. Turn the springs until the ends are facing you. The wire at the ends of both torsion springs here at the bracket should be pointing down. At the winding cones at the opposite ends, the spring wire points up. If not, reverse the springs. About once a month we get a phone call from a do-it-yourself customer who begins the conversation with, "I wound the garage door spring to about six turns and the spring came loose from the cone." We normally refer them back to this step and suggest they switch their springs.

Garage Door Repair How Much Centennial Colorado 80016


If your stuck garage door coincides with weather changes, you may need to adjust the pressure on the opener. Some openers have a force-adjustment mechanism that controls the force that's applied to operate the door. It's best to leave this adjustment to a garage door pro, as too much force may result in the door failing to stop when it should, posing a danger to people and objects in the door's path.

10.5 If the spring comes loose from the cone at about 6 turns, you are probably winding the spring backward because the springs are on the wrong sides. Switch the springs. Otherwise, after winding the torsion springs, you will need to stretch the springs and secure the winding cone. First, mark the shaft 1/4" beyond the winding cone with tape or with a file. We stretch the springs because the shaft floats horizontally between the flexible end bearing plates as the garage door operates. Although this may be as little as 1/4" the binding of the coils as the door closes often keeps the door from closing completely, especially when the springs and bearings are dry and need lubrication.
Dallas Texas, Plano TX, Garland TX, Highland Village, Lakewood, Las Colinas, Lewisville, Little Elm, Grapevine, Haltom City, Hurst, Keller, Forney, Carrollton, McKinney TX, Murphy Texas, Oak Lawn, Arlington TX, Parker TX, Plano, Preston Hollow, Richardson TX, Denton, Addison, Allen, Bedford, Coppell, Crowley, DeSoto, Euless, Flower Mound, Rockwall Texas, Garland Texas, Rowlett TX, Sachse TX, The Colony TX, Lavon Texas, Fort Worth TX, East Dallas, North Dallas, Wylie TX, White Rock Lake, area Lakewood, North Richland Hills TX, Benbrook, Burleson, Waxahachie, Red Oak, Irving TX, Mesquite TX
Remove the clamps and pliers from the torsion tube and track, and lift the door about 3 ft. by hand. If the door springs are properly adjusted, the door should stay in place when you let go. If the door falls when you let go, add a quarter turn to each spring. Repeat if necessary. If the door continues to open on its own, release spring tension in quarter-turn increments until the door stays in place when you let go. Then reconnect the opener.
Maybe the battery died or a spring broke, but you can't get into the garage to even see what the problem is. If the garage door is the only way in or out, or if you can't find the key to the door, you'll have to either find a way to break in or call a locksmith. As a preventative measure, it's smart to keep a spare key or install an emergency key release that would allow you to release the emergency disconnect to the operator so you can manually raise the door. https://youtube.com/embed/Z_eZc-kh40c
×