When you hire a professional, the first thing they will do is turn off the power as a safety precaution.  They will then measure the existing door springs to make sure the new springs they order or have in stock fit accordingly.  With these new springs, they will unwind the existing springs and install the new ones in its place, tightening them with screws.  When tightened, the springs will be balanced, lubricated and the springs will be wound up.  Lastly, the door will be tested and the tracks will be lubricated to move efficiently.
Step 1: Check the metal tracks inside the garage. Look at the mounting brackets that hold the tracks to the walls. If they're loose, tighten the bolts or screws at the brackets. Working inside the garage with the garage door closed, examine the tracks for dents, crimps, or flat spots. If there are any damaged spots, pound them out with a rubber mallet, or with a hammer and a block of scrap wood. If the tracks are badly damaged, they should be replaced.
Step 5: Check for loose hardware, and tighten as needed. On swing-up doors, check the plates where the spring is mounted to be sure the screws are tight, and tighten any loose screws. On roll-up doors, check the hinges that hold the sections of the door together; tighten any loose screws, and replace any damaged hinges. Sagging at one side of the door can often be corrected by servicing the hinges. If a screw hole is enlarged, replace the screw with a longer one of the same diameter, and use a hollow fiber plug, dipped in carpenters' glue, with the new screw. If the wood is cracked at a hinge, remove the hinge and fill the cracks and the screw holes with wood filler. Let the filler dry and then replace the hinge. If possible, move the hinge onto solid wood.

Garage Door Repair In My Area Centennial 80016


Sometimes, you’ll notice that your garage door closes all the way and then immediately goes back up instead of staying in the closed position. This issue usually arises with brand new garage doors that were just installed or older models that may need to be reset. If this happens, the most likely culprit is the open and close limit settings of your garage door opener.
After you’ve ordered your new garage door, we’ll perform a site inspection to confirm your door size. We’ll contact you to schedule the installation, and our professional installers will do the rest. They’ll deliver your door, take down the old door, reconnect your opener if there is one, seal your perimeter and provide a final walk-through where they’ll clean up the area and haul away your old door. Additional fees for haul away may apply in some markets. We are happy to provide answers to questions you may have at the time of your garage door and opener installation.

Garage Door Repair Estimates Centennial 80015


Unlike torsion springs, replacing extension springs has long been given the "green light" for DIYers, primarily because you can complete the job without having to deal with spring tension. The general process is simple and safe: open the door to relieve the spring tension (and secure it open with C-clamps in the tracks); disconnect the spring from the track bracket and the spring pulley, and disconnect the safety cable from one end; install the new spring, reinstall the pulley, and reconnect the safety cable, and you're done.
6.8 Properly tightened screws will loosen with less than a turn. Once you loosen a set screw, keep at least one bar in the cone AT ALL TIMES until the spring is fully unwound. Many cones have been over-tightened. The spring may unwind 1/4 turn and not unwind any more until one of the set screws is loosened some more. You may need to completely remove the set screws. The shaft may be distorted and the cone still may not unwind at all.
Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.

Garage Door Repair Bracket Centennial Colorado 80016


First, check to see if the transmitter on the wall inside your garage still opens your garage door when pressed. If it does, then the transmitter in your car likely just needs a simple battery replacement. If you have more than one car transmitter for your garage door, then your other transmitters will likely need new batteries soon as well, since they were probably installed around the same time.
If one of your door springs just broke and you are looking for instructions to decide if you can change the spring or springs safely and correctly, this page should help. DO NOT OPEN AND CLOSE YOUR GARAGE DOOR. Wooden garage doors are heavy and will probably damage or ruin the opener. The tops of steel doors often bend when operated with broken springs.

Garage Door Repair Free Estimate Near Me Centennial Colorado 80015


If you need to leave the door open until you can make repairs, block the door track on both sides so the door can't move, and unplug the garage door opener (if you have one). If you want to close the door, you can try closing it with the opener, making sure there's nothing in the door's path in case something goes wrong. However, this will put some strain on the opener. Alternatively, you can have a few strong helpers hold the door while you disconnect it from the opener and carefully close the door manually—again, it will be very heavy.

A1 Garage Door Repair Centennial Co 80016


Most garage doors from the past 15-20 years have a photo eye which detects if a person or object is blocking the door from lowering all the way. The photo eye will be about 4-6 inches off of the ground for most doors, with an eye that is about the size of a pea. It shoots a laser across the length of the garage that, if interrupted, will cut off the signal used to lower and raise the door.
2.4 The same is true of Older Overhead, BarCol and Raynor torsion springs that have winding cones with inconsistent hole sizes. If you insert a 1/2" X 18" bar in some of these holes you can move the opposite end of the bar over four inches. Bars in newer cones move less than 1 1/2". I've had many of the older cones spin loose from my bars, the last one generating an $1800 emergency room bill. If your cones are like any of these, or if they have more than 2" of play, leave the job of installing torsion springs to a professional garage door mechanic.
Received all items as indicated, I would recommend purchasing a metal center bearing also, other Than the plastic that this comes with. Install was easy and strait forward. hardest part was finding how many turns to tighten those springs?? I used a general rule of thumb of a full turn for every ft. Of door. 4 quarter turns equals 1 full turn. I found that 26 balanced the door perfectly. These springs seem a little smaller than what was there however, the coil itself is the same. (Pic) After installing, I recommend oiling the springs with some motor oil. This will help with rust and noise. Good luck with yours, it's worth the work for the saving!!
Usually, when a garage door spring breaks the door has already closed or come down. In some instances, however, a spring can snap while the door is closing or in motion, causing the door to fall rapidly. In these situations, the door can become a safety concern for you and your family, so you should keep your distance and call a garage door professional as soon as possible. Garage doors are very heavy and can cause injury if not handled properly. When a garage door problem occurs, call a Sears Garage Door expert to help.

Anytime Garage Door Repair Centennial 80016


The nucleus of any garage door system is its opener. Easily overlooked, garage door openers are highly complex pieces of equipment, often containing dozens of intricate parts that work simultaneously with one another to consistently raise and lower your door. You'll know that you're getting the best from Sears as it's the home to America's #1 Garage Door Opener Brand, Craftsman*.


Maybe the battery died or a spring broke, but you can't get into the garage to even see what the problem is. If the garage door is the only way in or out, or if you can't find the key to the door, you'll have to either find a way to break in or call a locksmith. As a preventative measure, it's smart to keep a spare key or install an emergency key release that would allow you to release the emergency disconnect to the operator so you can manually raise the door.

Garage Door Repair Free Estimate Near Me Centennial Colorado 80016


These instructions were first posted in 2005, and they were updated in August of 2008. I have been frank about the hazards of garage door repairs and about my own accidents incurred while replacing torsion springs. For what it's worth, you might be surprised to know that I, too, have benefitted from producing these instructions. I have not had any garage door accidents since we first published these on the web in 2005. And, in as much as I have helped keep other DIY-ers out of the emergency room, I consider myself somewhat of a medical practitioner.

Garage Door Repair In My Area Centennial Co 80015


Your dream car is parked in out of the elements, but it's not secure because the garage door won't lock. Most garage doors have two horizontal bars that move out from the center of the door into slots along the side of the door in the door track, effectively locking the door in place. Over time, these bars can shift slightly out of position so that they are no longer correctly aligned with the locking slots. To realign the bars, unscrew the guide brackets on the edges of the door so that they are loose enough to move, and then reposition them so that they smoothly guide the locking bars into the locking slots. Lubricate the lock mechanism with machine oil and you're done.
If you have a garage door opener and you suspect a spring has broken, do not disconnect the opener from the door (by pulling the red emergency release handle) while the door is open. If you do, the door can come crashing down under its nearly full weight, with nothing to stop it. This is an extremely dangerous situation. It is never safe to leave the door open when a spring has broken because someone might try to close the door without realizing how heavy it is. Or, they might pull the emergency release handle on the opener.

Aaa Garage Door Repair Centennial Colorado 80016


Does your door stop when going up? Does your look crooked? Can you see a break in the spring that runs along the side of the tracks? You might have a broken extension spring. Extension springs are generally used on smaller doors like an 8×7 or a 9×7. Extension springs are attached to the bracket that holds the horizontal track to the ceiling. The extend as the door goes down and with one broken the door cannot work properly. Typically one spring is broken and the other is not, however, we would replace both. They have both been used the same amount and springs break based off of usage. https://youtube.com/watch?feature=youtube_gdata&v=Z_eZc-kh40c
Springs are one of the primary components in all garage door systems. Torsion springs are usually mounted horizontally over the door opening. As the door closes, cables add tension to the springs and as the door opens that tension is released. The opening of the door causes the springs to unwind in conjunction with the weight coming off the door. This achieves a natural buoyancy. However, as the door moves up and down over time and the cycle count rises, the steel in the torsion springs will grow weak and will no longer be able to create energy or lift your garage door.

Garage Door Repair Free Quote Centennial Colorado 80016


Would have appreciated the technician to have explained in better detail about the quality of the first doors we received in our home. The garage doors that were installed recently were an upgrade. I would have selected the better quality of doors with the first installation if it had been explained in better detail and time of decision with the first doors. But, I really love the doors that were recently installed! Explained much better with the new doors. Time was well spent on my decision making and the technician this time was very helpful and knowledgeable. Thank You! Cathy Walsh 

Plus, we carry all the best and high quality products from the top garage door brands. Whatever is your requirement or need for your garage door, we are sure to have them in our comprehensive inventory. We have garage doors in different styles, materials, colors, designs and what-have-you. If you still cannot find what you are looking for, we can always source them out for you.


Instead, try other methods that might break the frozen connection between the door and the floor. For example, you can use a heat gun or hair dryer to melt the ice and free the door. Standard de-icing products can also work. And if you are careful not to damage the door or the seal on the bottom of the door, you can use a flat shovel or similar tool to chip away at the ice.

Garage Door Repair Guy Centennial Colorado 80016


Plus, we carry all the best and high quality products from the top garage door brands. Whatever is your requirement or need for your garage door, we are sure to have them in our comprehensive inventory. We have garage doors in different styles, materials, colors, designs and what-have-you. If you still cannot find what you are looking for, we can always source them out for you.

On one-piece doors with side springs, you open the door to relieve the spring tension, and simply swap out the springs on the opener-arm mechanism; there are no cables or pulleys to deal with, and the springs have internal safety rods. Some doors have tensioners that maintain moderate tension when the door is open all the way, and on these you'll have to loosen the tensioner in order to remove the spring.
"Our garage door wouldn’t shut on sunny days and the tech came out. He explained my options (swap the “seeing” sensor with the other, or replace them). He tried swapping and it was still an issue so he replaced them. In addition, he adjusted the spring because the company that installed it last year did not adjust it properly. He was here for about two hours and charged us for only the sensor replacement. Will definitely be using this company again! Highly recommend them. "

Garage Door Repair Installation Centennial Co 80016


Clean the photoelectric safety eyes at the bottom of the door track with a clean rag if the opener did not operate with the push button. Sometimes dirt and moisture will keep the eyes from making a good connection. Push the wall button again to see if the opener operates. If the opener does not operate, call a door professional to troubleshoot your door opener. Meanwhile, you can still open and close your door manually.

Lower the door and dismantle it by removing the hardware. Lower a double door by recruiting at least two helpers to help with the weight, and place a 2×4 block under the door to prevent smashing a foot or finger when it’s lowered. Remove the sections one at a time by disconnecting the rollers and brackets. If you have windows, tape them to help control flying shards if they break. Then remove the old roller tracks and remaining hardware.
Doors come with one or two torsion springs. If either spring is broken, the garage door opener may struggle to lift the weight of the door or fail to open the door at all. If a spring is broken, call a professional for service as these can be very dangerous to work with. Don’t try to open the door until a professional comes to inspect it and replace the springs. Springs can only be used for a certain number of open and close cycles, and over time they will eventually break and need replacing.
In need of garage door repair? Contact one of our many well-trained garage door repair professionals today to provide your garage door system with the recommended service and maintenance procedures for smooth and reliable operation. Our garage door repair professionals are here for you, whether you want to fix your existing garage door or buy a new garage door. Are you looking to replace a garage door spring, cable or roller or searching for 'garage door repair near me'? Use our distributor locator below: 
Gather the supplies and tools needed for changing the springs safely. In addition to the torsion springs you'll need a minimum of one or two 10" vise grips, an adjustable wrench, and two 1/2" X 18" winding bars. Most hardware stores sell 1/2" X 36" steel rods that can be cut in half. You'll also need a firm ladder and a rag for cleaning your hands. A ruler and a file may also be necessary; a socket wrench and sockets would shorten the time required. Finally, make sure your garage is lighted well.
6.8 Properly tightened screws will loosen with less than a turn. Once you loosen a set screw, keep at least one bar in the cone AT ALL TIMES until the spring is fully unwound. Many cones have been over-tightened. The spring may unwind 1/4 turn and not unwind any more until one of the set screws is loosened some more. You may need to completely remove the set screws. The shaft may be distorted and the cone still may not unwind at all.

With every spring repair, Precision provides a free safety inspection to make sure all the hardware and moving parts on your door are in good working condition and meet safety standards. Since the hardware was probably installed at the same as the springs, it's possible there are worn mechanical parts on your door that are in an unsafe state. Think about spring failure as a symptom to a possibly larger problem with your door. This is why it's a Precision Best Practice to provide a free safety inspection and maintain a safe environment for our customers.

Garage Door Repair Centennial Colorado 80015


The technician did a wonderful job - arrived on time and completed the job in less than 2 hours. I would have given him a 5 on everything if he had returned to add the additional piece (a piece that is fixed to the door frame for better insulation) to my door on the outside on the day he said he would come back. The piece he brought was of wrong color and he said he would be back with the right color the first day after New Year's Day to put up the piece. I hope he can come back soon.
The technician, Robert Helton, was very pleasant, helpful, and professional. He repaired the garage door opener expeditiously and explained why it hadn't worked properly. He also checked the chain mechanism and the door itself and showed me how to manually work the door should I need to do that in the future. I was very pleased with this repair work.

Garage Door Repair Near Me Centennial Co


Torsion springs are located above the opening of your door with springs that slide onto a bar. Extension spring systems can be found alongside the opening of the door. It's important to know whether or not a garage door company provides service for your needs. Precision's professionally trained technicians are fully equipped to work on torsion and extension spring systems. http://m.youtube.com/e/Z_eZc-kh40c
×