9.9 Go to the other side of the garage door and insert the end of the cable into the drum. Rotate the drum until the cable is tight. Slide the drum against the bearing and push the shaft to the right. The marks should line up. If they don't, figure out why and correct the problem. It could be a stuck cable, the garage floor may have shifted, or the vertical angle that helps support the bearing plate may have loosened and shifted. Many garage doors have been installed with a gap between a drum and a bearing plate. The cable drums should always be flush against the race of the bearings.


Received all items as indicated, I would recommend purchasing a metal center bearing also, other Than the plastic that this comes with. Install was easy and strait forward. hardest part was finding how many turns to tighten those springs?? I used a general rule of thumb of a full turn for every ft. Of door. 4 quarter turns equals 1 full turn. I found that 26 balanced the door perfectly. These springs seem a little smaller than what was there however, the coil itself is the same. (Pic) After installing, I recommend oiling the springs with some motor oil. This will help with rust and noise. Good luck with yours, it's worth the work for the saving!!

Often companies will show different types of springs like oil dipped, galvanized or powder coated and try to convince you that one is longer life than the other and that is why it is going to cost this much instead of that much. Galvanized and Powder coated are great for coastal areas as a rust preventative but do not change the cycle life and do not cost but a few dollars more.
10.2 Tape your winding bars if you have not done so already, not only to assure that you are inserting the bars completely into the cones as you wind the torsion springs, but more importantly to assure that the bar does not slip out of the cone when you stretch the springs at the end. This has happened to me several times. Professionals always stretch torsion springs after winding them because the shaft floats horizontally between the flexible end bearing plates as the door operates. Although this may be as little as 1/4", the binding of the coils as the garage door closes oftentimes keeps the door from closing completely, especially when the torsion springs and bearings are dry.
"We had an unusual repair requirement. We have horizontal sliding steel doors on our 1950's equipment shed. The upper track was damaged by a roofer's forklift while they were loading supplies onto the roof. The track is made out of very heavy steel, not like the track in today's doors. Toby, responded to my request very quickly and came out of his way to inspect the damage. Although it was not something that he had encountered before, he was able to fix the track and the door is operating better than it has in years. Thank you."
If your garage door is equipped with only one torsion spring, it will be much harder to get your door open. You will need to get 2-3 people to help lift the door up because the full weight can be anywhere from 150 to 300 pounds. We don’t recommend lifting the door when the spring break's due to the danger of it falling on someone. If you absolutely must get your garage door open, raw strength is what you need. When you get the door in the up position, use vise-grips or a c-clamp on the track below the bottom roller to hold the door in the up position.

Affordable Garage Door Repair Centennial Co 80015


Every homeowner can relate to how life's inconveniences are thrown at you at the worst possible times. The last thing you want to happen is have your car stuck in the garage when you need it most, especially when it's only been a couple months, weeks, or even days after your last garage door repair! That's why Precision leads by example and follows the industry's best practices in order to make the best recommendation to homeowners each time we step foot in a garage. http://www.youtube.com/v/Z_eZc-kh40c
If you pull the red emergency release rope on your automatic opener and you still can’t lift the garage door, you probably have a broken spring. The counterbalance spring is what lifts the garage door, not the garage door opener. If the spring is broken, the door is dead weight. A garage door can be lifted, but it is going to require some muscle to get it up. It is also important to lift the door evenly so it does not jam in the tracks.
There are knobs or dials located somewhere on your garage door motor that you can use to adjust the limit settings. The exact location and resetting procedures will vary depending on the brand and model of garage door you have. Your owner’s manual should have more specific information on how to adjust your limits. You may need to experiment with a few adjustments before finally getting the correct setting. If you find that adjusting the limit settings isn’t working, it might be time to call a technician to come and help get your garage door to stay closed.

One of the best ways to care for your springs is to check them over for wear. You can certainly look at them for damage, but sometimes the damage isn’t something that’s visible. In these cases, try lifting the garage door up from the ground. About halfway up, let go. If the door stays, the springs are still working perfectly. If the door sags or drops at all, this could be a sign that your springs are beginning to weaken and will need replacing soon.


You may remember a time as a kid when you and your siblings would close the garage door and run underneath it as fast as possible to make it out before the door closed. Well, on any garage door installed after 1993, that’s no longer possible thanks to two tiny photo eyes on either side of the garage entrance. These photo eyes transmit an invisible beam between each other that detects if anything is in the garage door’s path when it closes. This safety measure is there to prevent automatic garage doors from closing on top of someone or something and causing serious injury or damage to property.
11.2c If the springs you installed are too weak, and you wind the springs the correct number of turns, the door will be heavy at the floor, and it will not stay open half way, but it will stay open if raised completely. If tension is added to the torsion springs to lighten the garage door and to get it stay open half way, the door will be harder to close; openers often damage the new steel garage doors when they are too hard to close.
A common material for a new garage door is steel sheet formed or stamped to look like a raised panel wooden door. Steel doors are available in uninsulated, insulated, and double skin steel. A design mimicking carriage house doors has become popular since early 2000s, and many manufacturers clad the exterior of a steel door with composite, vinyl boards, or other trim to give it the appearance of wood.
Chris was very professional & thorough. He arrived on time & was able to answer all questions that I had. I was extremely satisfied with the quality of the work he performed. I spoke several times on the phone with Mrs. Carol who keep me informed prior to, during, and after the installation of my garage door. She was very professional, easy to talk with and resolved any misunderstanding that I had.
I went on Garage Door Nation website to look at the conversion chart from 1 to 2 torsion springs. For my 1 spring, size 2"/0.250ID/30.5" length, they recommended 2 of 2"/0.207ID/24" length. I got this kit from Amazon for $64 with $11 overnight shipping even though I could get free shipping through Prime over the weekend, but I couldn't wait for 3 more painful days. Installed it followed YouTube video. Worked better than my old one, a lot quieter. Check the video if you want to install one yourself. Professional installation costs hundreds of $$$: http://youtube.com/watch?v=Z_eZc-kh40c&app=desktop
If you have a steel door, but want the look of a wood one, it is not necessary to change your entire garage door. Often, it may be possible to mimic the look of wood with skillful painting. Your local home improvement store may be able to provide good advice about the type of paint and brushes needed to mimic the look of wood for your particular door material.

Instead, try other methods that might break the frozen connection between the door and the floor. For example, you can use a heat gun or hair dryer to melt the ice and free the door. Standard de-icing products can also work. And if you are careful not to damage the door or the seal on the bottom of the door, you can use a flat shovel or similar tool to chip away at the ice.

Garage Door Repair Guy Centennial Colorado 80016


Copyright © 2019 HubPages Inc. and respective owners. Other product and company names shown may be trademarks of their respective owners. HubPages® is a registered Service Mark of HubPages, Inc. HubPages and Hubbers (authors) may earn revenue on this page based on affiliate relationships and advertisements with partners including Amazon, Google, and others.


Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring.

• Extension springs: Garage door extension springs stretch to provide lifting power for the door. These springs are typically made of steel and mounted above the horizontal track of the garage door. A safety cable should run through your extension springs to prevent possible injuries or property damage. Extension springs are the most common type of garage door spring for residential use and can break after excessive usage.

Garage Door Repair Average Cost Centennial Colorado 80016


First, make sure your transmitter isn’t stuck under something that could be pressing on the button. For example, your transmitter may have fallen under your car seat and the button is accidentally being pushed by something heavy rolling around on your floor. If that’s not the case, you may also need to check your transmitter’s frequency. It’s possible your neighbors could be running their garage doors on the same frequency as yours, and as they drive by, they’re opening their garage door along with yours.
The tricky parts of the job involve you carrying the tension of the spring. Replacing a spring requires that you first unwind the spring to relieve the tension, then wind it back up and secure it while it's under tension. Winding bars are used for all winding and unwinding actions—don't try to save a few bucks by substituting long screwdrivers or pieces of rebar for the real winding bars. Substitute tools are much more likely to slip, or they may bend or break under the load of the spring. 

Quite a few garage doors come with manual locks, especially older models, for added security for your house. These typically look like a knob or handle in the middle of your door with two bars running horizontally from each side. There may be a small button on the top or side of the handle that you can press to slide the bars across the doors, thus locking the garage door from the inside. It can be somewhat easy to accidentally hit that button, especially if you’re getting large objects out of the trunk of your car near the door.
Because your garage door is a major entryway to your home, it is important to keep it in good working order for your own safety, security, and convenience. Choosing the right style and appropriate materials will lessen the amount of repairs that may arise. Additionally, investing in regular maintenance can be cost-effective in the long run. If your garage door is in need of major repair, it is best to call a professional garage door repair company for assistance. Typically, the company will charge for at least one hour for making a service call. However, the benefits of a professional repair job can well outweigh any costs, as a professional can ensure the safety, security, and proper operation of your garage door.
A1 Garage Door Service is the trusted service provider in installing, servicing and repairing all kinds and types of garage doors. We encourage you to check out the reviews of the people of Phoenix and Gilbert on the kind of garage door service that we provide. Our customers have consistently given us A+ ratings on BBB, 5-star ratings on Yelp and the Super Service Award on Angie’s List to express their satisfaction on our service.
Measure area labeled headroom (5), which is the distance between the top of the door opening (jamb header) and the ceiling (or floor joist). 10" is required for the standard extension spring or EZ-SET® Extension Spring System while 12" is required for a standard torsion spring and EZ-SET® Torsion Spring System. If you have restricted headroom, special hardware is available. Additional headroom is required for installation of an automatic garage door opener. NOTE: If garage door height extends above the opening, the headroom measurement should be adjusted proportionately.
ryan was way more than early when he showed up. ryan gave me a straight up, not nonsensical "ah..ah..." like someone making up a story to listen to. direct and to the point, like a professional, gave me my options that i could present to the boss. the boss didn;t like the price of the new rollers. but she loves that it doesn't sound like a tank coming home from war. we were completely unprepared for this, so, it's good we got a guy like ryan.
If your photo eyes are clean and the door still isn’t closing, the next thing you’ll need to do is check the alignment of the eyes. The eyes should be pointing in exactly the same direction and at the same angle. If they’re off, they won’t register that the other one is there, and it’ll assume something is in its path, causing the door to stay in the open position. When checking the alignment, measure the height of each photo eye from the ground. Use a level to make sure they’re pointing directly across at each other at the same angle. A laser level will make this part a little easier, but if you don’t have one, a regular level will work as well. https://www.youtube.com/embed/Z_eZc-kh40c
×