The garage we take for granted very likely stores thousands of dollars worth of tools and household belongings, not to mention your automobiles. Yet this space is typically rather easy for intruders to penetrate. Garage security can be greatly improved by installing a modern garage door opener that features rotating digital codes, which can foil even the most tech-savvy prowlers.
If this is the problem then you will be able to tell by seeing if your garage door rollers are literally off track. If your garage door panels are not damaged, then you do not need to replace your door. However, the rollers do need to be put back on the track which should be done by a professional. If you are looking for a garage door company that specializes in Garage Doors, Garage Door Repair, or Garage Door Openers, or are just looking for more information, please visit our website at precisiondoor.net. Remember, "We Fix Garage Doors Right"™.
Most garage doors from the past 15-20 years have a photo eye which detects if a person or object is blocking the door from lowering all the way. The photo eye will be about 4-6 inches off of the ground for most doors, with an eye that is about the size of a pea. It shoots a laser across the length of the garage that, if interrupted, will cut off the signal used to lower and raise the door.
Garage doors are able to move due to a counterbalance system that usually consists of a torsion spring. We often find incorrect springs have been installed which result in an unsafe door that you may not be able to open manually when needed. The balance of your garage door should be tested annually to reduce wear on your garage door opener and ensure it can be opened if an emergency situation arises. Because of the dangers involved with torsion springs, garage door spring repair and installation should only be done by experienced professionals like our Medics.
Both types of springs are loaded, or under tension, when the door is closed. This gives them stored energy to help lift the door as it's being opened. When the door is all the way up, the springs are relaxed, or relatively so—they still may be under some tension. The mechanical difference between extension and torsion springs is that extension springs are loaded by stretching, or elongating, while torsion springs are loaded by twisting, creating torque.
The garage door opens and closes many times throughout the year, and something may blow inside. While it is usually something such as loose leaves or small amounts of dirt, the rails that the door travel along can collect this loose debris. Over time, the buildup of debris creates a blockage on the rails. Note where on the rails the door is stuck and clean that area. If children use the garage to leave the house, it's sometimes something as simple as a small, bouncing ball that happens to land in just the right -- or wrong -- spot. https://www.youtube.com/watch?v=Z_eZc-kh40c&hc_location=ufi
On our EZ-Set Torsion Springs page you will find several options for replacing these springs. We also have step by step instructions for EZ-Set Torsion Spring Replacement. In addition, one of our customers has provided excellent EZ-Set Torsion System instructions for removing the spring without wrecking the winding unit that secures the stationary cone. Instead of a spanner tool, you may prefer to use a pipe wrench or large channel locks to hook the end of the spring and remove it from the cones in the last step. https://www.youtube.com/watch?v=Z_eZc-kh40c&feature=kp

If you need to leave the door open until you can make repairs, block the door track on both sides so the door can't move, and unplug the garage door opener (if you have one). If you want to close the door, you can try closing it with the opener, making sure there's nothing in the door's path in case something goes wrong. However, this will put some strain on the opener. Alternatively, you can have a few strong helpers hold the door while you disconnect it from the opener and carefully close the door manually—again, it will be very heavy.

Garage Door Repair And Service Centennial Co


Chris was very professional & thorough. He arrived on time & was able to answer all questions that I had. I was extremely satisfied with the quality of the work he performed. I spoke several times on the phone with Mrs. Carol who keep me informed prior to, during, and after the installation of my garage door. She was very professional, easy to talk with and resolved any misunderstanding that I had.
As the door is opened and closed over time, the steel in the springs can start to weaken as the door gradually becomes too heavy for them, rendering them less effective. The springs will eventually break, leaving the door closed. Torsion springs can also be affected by rust and cold weather. The good news is, the average garage door torsion springs will last somewhere between 5-7 years, and should last around 10,000 cycles. So, if you open and close your garage door 3-5 times a day for over 365 days in a year, you should get plenty of life out of your torsion springs.

Your door’s torsion spring is located approximately one foot from the top section of your door when it is closed. It consists of two large coil springs, and is approximately the length of your arm. Its purpose is to balance the weight of your door so that a door weighing between 160 and 185 pounds is practically weightless to lift. As such, it makes it possible for a garage door opener to raise the door using only ten pounds of pressure.


If your garage door track is out of alignment, it can be a serious issue. The metal track your door runs on needs to be aligned properly in order for your door to move. If you see gaps between the rollers and rail, or bends in the rails themselves, you have a problem. The heavy weight of the door can compound these issues and make them worse until it becomes dangerous to operate your door.
If the door opens this way, then there’s probably something wrong with the garage door opener. It’s a good idea to make sure the opener is plugged into its nearby power outlet. Also, make sure the circuit breaker for the garage door opener hasn’t flipped to the “OFF” position. If it has, then there may be an electrical issue that your garage door specialist should check out.
Usually, when a garage door spring breaks the door has already closed or come down. In some instances, however, a spring can snap while the door is closing or in motion, causing the door to fall rapidly. In these situations, the door can become a safety concern for you and your family, so you should keep your distance and call a garage door professional as soon as possible. Garage doors are very heavy and can cause injury if not handled properly. When a garage door problem occurs, call a Sears Garage Door expert to help.

Anytime Garage Door Repair Centennial 80016


Inspect the area around your garage door to see if something is blocking the photo eye sensors. Then look at the tracks to see if there is any buildup on the inside. You’ll need to get a step ladder to look at the tracks on the top part of your garage, as it will be difficult to see from ground level. It may also not be a bad idea to proactively wipe down your garage door tracks periodically to prevent this type of buildup from occurring. Running a damp rag along each track should be enough to remove anything that’s lingering on the tracks.
I got these replacement cables for my beach house garage door after the originals rusted and broke. These are twice the diameter of the OEM cables, and fit the door perfectly. The larger cables give piece of mind for both supporting the door and providing safety cables for the extension springs. Came with all the necessary hardware, and the installation was easy with the doors blocked in the up position. http://youtube.com/watch?feature=youtu.be&v=Z_eZc-kh40c
Garage doors cause injury and property damage (including expensive damage to the door itself) in several different ways. The most common causes of injury from garage door systems include falling doors, pinch points, improperly adjusted opener force settings and safety eyes, attempts at do-it-yourself repair without the proper knowledge or tools, and uncontrolled release of spring tension (on extension spring systems).
Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.
4.4 Take the spring on the left and place it at the left end of the door as pictured here. Notice that the end of the wire points to the right toward the center of the door. This is a right wind torsion spring. It will go above the garage door on the left side of the spring anchor bracket. The winding cone at the other end of this spring is usually painted red.

Affordable Garage Door Repair Centennial 80016


Locating a contractor - there are many professional overhead garage door companies. It is always advisable to contact at least three different agencies and request a bid or quote for the work. Be sure that each quote includes the costs for a few different types of doors, any installation fees, and the cost of wiring the electronic openers. Standard prices range from:
Garage door springs come in two styles: torsion (see above), which mounts on the header above the door, and extension (Photo 1), which floats above the upper roller track. In the past, extension springs were safer to install but didn’t have containment cables running through the center of the spring. Without cable, these springs become dangerous, heavy whips when they break. They also tend to be noisier than torsion springs, and we recommend you use them only if you don’t have the 12 in. of headroom above the door that a torsion spring requires.

Garage Door Repair Companies Centennial 80016


When it comes to garage doors, functionality and safety are equally important in the eyes of Sears Garage Door technicians. Our associates know the importance of garage door safety and the hazards that a faulty garage door can pose for your family. To confirm that your garage door and opener operate safely, our technicians perform a 20-point safety check during maintenance calls and repair jobs. This safety check verifies that any repair work performed has been done correctly and that there are no lingering safety problems with your door and mechanisms. If our technician discovers any safety concerns, he’ll advise you on the best way to proceed with correcting the problem.

Automatic Garage Door Repair Centennial Co 80016


Instead, try other methods that might break the frozen connection between the door and the floor. For example, you can use a heat gun or hair dryer to melt the ice and free the door. Standard de-icing products can also work. And if you are careful not to damage the door or the seal on the bottom of the door, you can use a flat shovel or similar tool to chip away at the ice.

It’s difficult to say how often the springs will need to be replaced since it’s different for everyone. It depends on how often you use your garage door, how cold and long your winters are, how well you maintain your springs and many other factors. The best rule of the thumb is to check your springs regularly for signs of wear and damage and to replace them when they begin to appear tired.


Product was received in two days and was as advertised. Installing these myself saved around $150 but it took around 2-3 hours. I would imagine everyone's experience is going to be different. These springs appear to be heavier duty than the ones they replaced. I couldn't use the same slots for tension as the old ones and it was trial and error in adjusting the length of my pull cable until the door closed as it should. I need to replace the springs on my other garage door and would think that will take less than an hour based on what I learned from the first install.
Next, check to see if your garage door operator is the problem. Do this by pulling the emergency release cord when the door is in the down position (so the door doesn’t come crashing down in case there is a problem). Then, try to lift the door up manually. Does it open easily? If so, your opener is probably at fault. If it still doesn’t move, the problem likely lies with your tracks, springs, or rollers.
Nate was very courteous and professional and called to let me know that he was about 30 minutes from my house. I had purchased a new Sears garage door opener, but when Nate arrived at my home, he inspected the existing unit and told me that it was still in good shape except for a worn out part. Nate procured the new part and brought it to my home this morning. The unit was repaired in about 10 minutes! The existing unit was just over five years old, so I'm glad I will get some more use out of it.
If you have a steel door, but want the look of a wood one, it is not necessary to change your entire garage door. Often, it may be possible to mimic the look of wood with skillful painting. Your local home improvement store may be able to provide good advice about the type of paint and brushes needed to mimic the look of wood for your particular door material.

Asap Garage Door Repair Centennial Colorado 80016


We look out for the safety of our customers and their families. That’s why we do not sell garage door torsion springs separately to consumers, and it’s also why we recommend putting your broken garage door in the hands of our experienced technicians. At Garage Door Medics, we are licensed, bonded, and insured. We have completed thousands of garage door installations and spring repairs, and we make sure they are done safely and with the right springs for your garage door system.

Garage Door Repair Free Estimate Near Me Centennial Colorado


Scott was exceptionally polite, professional and knowledgeable. He thoroughly checked my garage door opener, but also inspected the garage door itself and pointed out rust and deterioration that has occurred. Scott then gave me a quote on a new garage door, explaining the installation procedure and quality elements of the new door including the warranty. I was very pleased with the entire service appointment, and my husband and I are seriously considering the new garage door, but only if Scott is the installer! Thanks, Scott!

Garage Door Repair Cost Centennial Colorado 80015


How much should a garage door spring replacement cost? The national average is between $200 and $300 for a professional to come to your house and replace two springs. On line sources suggest a higher price of over $700 and that you will save $500 or more by replacing springs yourself. This is simply not true. To find the cost for replacing springs in your area look for a reputable company through Yelp or the Better Busienss Bureau. If clicking a site's BBB logo doesn't take you to the BBB site, we advise purchasing your springs from a different company.
My garage door has been acting up. Not wanting to work sometimes. I noticed the blue light flashing on the opener when I push the remote button. Today it will not open. That is the only way in, so I can't go in the garage from inside the house. I can't pull the cord to release the belt drive. How do I open it now? I never did run wires to the manual button into the house. I have to use the opener. Only have one I can find now. It is not working. I need in there now.

Garage Door Repair Free Quote Centennial Co


Torsion springs are located above the opening of your door with springs that slide onto a bar. Extension spring systems can be found alongside the opening of the door. It's important to know whether or not a garage door company provides service for your needs. Precision's professionally trained technicians are fully equipped to work on torsion and extension spring systems.

Garage Door Repair And Service Centennial Colorado 80015


Measure the various areas where the door will be installed: door-opening height and width, headroom (from top of opening to ceiling), and back room (length of garage). For the headroom, you should have about 10" to 12" of space, depending on the spring system you're installing. For the back room, you should have the door height, plus another 18" or more of space.
Another scenario is the garage door goes up very slowly when using the automatic opener. Some garage door openers have DC motors that start off slow when opening and then kick into a higher speed. If you have a broken spring, the opener might stay in the slower speed due to the heavy weight of the garage door. If this happens to you, close the garage door and pull the emergency release rope. Next, try to lift the door. If it is really heavy, then you most likely have a broken garage door spring.

The average cost is $190 for 2 springs in the Detroit area. This is for steel doors weighing under 140 lbs or known as a standard spring which fits 90% of all doors. The remaining 10% are wood doors or large heavy insulated doors. Expect to pay an additional $60 - $100 for a set of these. Garage Door Companies rarely carry these springs on their vehicles or stock them. Therefore, they either buy them locally at a premium or special order them. Regardless, its an additional trip that gets figured into the cost.
It is very important that the replacement springs are calibrated for the weight of your door. Using the wrong size garage door springs will caused the to not function properly and could also cause the opener to break much quicker. Replacing extension springs can be very dangerous and if done wrong can harm someone using the garage door. Make sure you call the Garage Door Doctor to ensure your garage is repaired properly!
If you have a single-car garage, an extension spring will do the job. If you’re looking for a smoother motion and an ability to lift heavier doors, you may be better off selecting the torsion spring option. And if you have a two-car garage, your door will likely be too heavy for an extension spring. In this case, the torsion spring is the better choice.
Most homeowners never know they have a broken garage door spring until they try to leave their home. You go in the garage to open the door, push the wall button, and the door only goes up 6”. The reason for this is the garage door opener force or sensitivity has activated, causing the opener to stop pulling the door up. This is a safety feature built into most garage door openers. It is actually a good thing when the open force activates to prevent any damage to your garage door or opener.
6.7 It's now time to unwind the spring. Firmly position yourself on a steady ladder beside the garage door. Next, insert the bar into one of the holes of the winding cone. Make sure it goes all the way in. It should click when your bar hits the core. If you want to test the force you will be handling before loosening the set screws, push up on the bar one quarter turn and bring it back down. Next, while grasping the other end of the bar firmly, loosen the set screws with an open-end wrench or small adjustable wrench loose enough to come free should the cone spin. Be prepared for the torque to be transferred to the bar.

Garage Door Repair How Much Centennial Co


Test the garage door opener while the door is down. Push the wall button to operate the door opener. If the opener operates, the binding was setting the internal safety mechanisms off, alerting the opener not to close. Raise the door slightly and jiggle the emergency cord to lock the carriage back over the carriage base, and attempt to operate the door with the motor.
We look out for the safety of our customers and their families. That’s why we do not sell garage door torsion springs separately to consumers, and it’s also why we recommend putting your broken garage door in the hands of our experienced technicians. At Garage Door Medics, we are licensed, bonded, and insured. We have completed thousands of garage door installations and spring repairs, and we make sure they are done safely and with the right springs for your garage door system.

Anytime Garage Door Repair Centennial Colorado 80015


The following procedures are based on my 30 years in the garage door industry. In spite of my high mechanical aptitude, even after 18 years in the trade I lost the end of my left index finger. A few years later I had five stitches in my right thumb, and a year later five stitches in my left thumb. In 2004 emergency room staffs dug steel out of my eye and sewed up my ring finger with eight stitches. The best I can do is help you minimize the risk of injury; that's all I can do for myself. I am not so naive as to think that I have made my last trip to the emergency room. Repairing garage doors, particularly replacing torsion springs, is dangerous work, whether you are a do-it-yourself homeowner or an experienced technician.

Garage Door Repair Estimates Centennial Colorado 80015


Mechanical garage door openers can pull or push a garage door with enough force to injure or kill people and pets if they become trapped. All modern openers are equipped with “force settings” that make the door reverse if it encounters too much resistance while closing or opening. Any garage door opener sold in the United States after 1992 requires safety eyes—sensors that prevent the door from closing if obstructed. Force settings should cause a door to stop or reverse on encountering more than approximately 20 lbs (9.07 kg) of resistance. Safety eyes should be installed a maximum of six inches above the ground. Many garage door injuries, and nearly all garage door related property damage, can be avoided by following these precautions.

Garage Door Repair Centennial Colorado


I have 2 full house humidifiers that have stopped functioning right. There are new filters, fan runs, tanks are full of water but they are not empting into the base. They have worked for part of the winter and now nothing seems to help...I loosened the caps thinking I had them too tight..... nothing seems to work .I have had humidifiers for 20 years and this is the first time this has happened to me. The humidifiers are only 2 years old. Any suggestions??
To install a single new garage door it should cost between $500 and $800. They demonstrate that the average homeowner can usually tackle such a project in a nine hour time span and a professional will be able to complete it in roughly five hours. Should it be a DIY project? Not really, most housing experts point out that it is a two-person job, requires advanced carpentry skills, and even knowledge of household electronic systems.

Guest 9232954 -- check out the other answers for this question, and the links below the answers for even more - seems from $125-400 range from different contributors (should be replaced in pairs for balanced lifting unless one spring is quite new), about $200-250 or 300 seems a common charge. The springs themselves generally run about $20-50 each depending on lead they have to carry.

9.14 Slide the springs to the bracket. Double-check to make sure you have the right wound spring on the left side and the left wind spring on the right side. Turn the springs until the ends are facing you. The wire at the ends of both torsion springs here at the bracket should be pointing down. At the winding cones at the opposite ends, the spring wire points up. If not, reverse the springs. About once a month we get a phone call from a do-it-yourself customer who begins the conversation with, "I wound the garage door spring to about six turns and the spring came loose from the cone." We normally refer them back to this step and suggest they switch their springs.

Garage Door Repair How Much Centennial Colorado 80016


Install the vertical roller tracks first by wrapping the curved lip around the rollers. The top of these tracks should be approximately 8 in. below the top of the top section. Wait to install the upper tracks until this step is complete. Check the level of the top section to make sure the tops of the vertical roller tracks are level with each other. The bottom of the roller tracks should be at least 1/8 in. off the concrete floor. After leveling and mounting these tracks, install the upper roller (horizontal) tracks.
6.8 Properly tightened screws will loosen with less than a turn. Once you loosen a set screw, keep at least one bar in the cone AT ALL TIMES until the spring is fully unwound. Many cones have been over-tightened. The spring may unwind 1/4 turn and not unwind any more until one of the set screws is loosened some more. You may need to completely remove the set screws. The shaft may be distorted and the cone still may not unwind at all.
Homeowners have long been warned that torsion springs are extremely dangerous to work with and that replacing them must be left to a professional. But these claims are somewhat exaggerated. If you understand how they work, and you pay attention to what you're doing, you can replace them safely and surprisingly easily. Granted, they're a little spooky to work with at first (partly due to their reputation), but this is a good thing—you really don't want to forget that they're under tension. Thinking about every step — before you take it — is the key to staying safe.
Steel entry doors - when a garage is being fitted with new doors, it is also a good idea to consider a separate single 3x68 exterior door with half-glass and locksets too. These may require some carpentry, but they are a good way to allow for some flexibility in the choice of larger garage door, and can ensure that the homeowner will have more than a single way in or out of the structure. The average costs for such a feature range from $250 to $1000 each. http://www.youtube.com/watch?feature=youtu.be&v=Z_eZc-kh40c

The power to your garage is out with the door shut, and you need to get your car out or you'll have to take a bus. You'll notice a cord—usually with a red handle—dangling down from the guide track that the opener uses to open and close the door. This is the manual override. Once pulled, it allows you to open and close the door with your own power in the form a little elbow grease.

It is very important that the replacement springs are calibrated for the weight of your door. Using the wrong size garage door springs will caused the to not function properly and could also cause the opener to break much quicker. Replacing extension springs can be very dangerous and if done wrong can harm someone using the garage door. Make sure you call the Garage Door Doctor to ensure your garage is repaired properly!

Garage Door Repair Companies Centennial Co


Slide the left spring onto the tube and add the cable drum. When your new springs arrive, put the new left spring (the 1 with the end facing up and to the left) on the torsion tube, making sure that the stationary cone on the end of the spring faces the center bracket. After sliding the new spring into place, replace the cable drum and insert the torsion bar into the left bearing bracket.[9]

Garage Door Repair Estimates Centennial Co


Replacing torsion springs is done with the door closed. You start by carefully unloading all of the springs (most standard-size doors have two; any broken spring will already be unloaded), using the winding bars. Then, you unbolt the springs from the central rod bracket, disconnect the cables from the pulleys, and loosen the pulleys and slide them off of the rod. Next, you swap out the springs, reinstall the pulleys and cables, and secure the inside ends of the springs to the central bracket. Finally, you wind up both springs (securing them with two setscrew bolts on the winding cones) and test the door for proper spring tension. Often, springs need an extra quarter-turn or two to get the door balance just right.
However, when a car is trapped inside, then it must be opened; otherwise, taking a cab or bus would be the only option left. Opening it would require help from another adult person or should be done by technicians. And every attempt in opening it, safety precautions should always be the first thing in mind. Never rely on garage entry openers when the spring is broken since it can cause falls and accidents. If the homeowner is not confident to open it or has no time to do it, it is always wise to call a technician.
Torsion springs do not last forever, regardless of what some companies claim. “Lifetime” springs do not exist – all springs have a lifespan. Most builders typically install the lowest costing door available and with that generally comes lower cycle springs. A torsion spring’s life is determined by the number of cycles the spring is rated to last. Whenever the door goes up and down is what is referred to as a “cycle.” The springs that builders install can last as little as 7,500 cycles which means the average homeowner could get 3-5 years of life.

There are two types of garage door springs: torsion and extension. Torsion springs are horizontal and located near the top of the garage door. Check for a gap between these springs indicating a break. Springs on the sides of the garage door are extension springs. Inspect them to see if one or both of them have broken. If you have a broken spring, call a garage door technician to fix it for you as soon as possible. Never operate a garage door with a broken spring; it could severely damage the door and the operating system. Never attempt to replace a broken spring on your own, either. Replacing broken garage door springs is very dangerous for anyone other than a certified, professional repair technician.


Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.
Instead, try other methods that might break the frozen connection between the door and the floor. For example, you can use a heat gun or hair dryer to melt the ice and free the door. Standard de-icing products can also work. And if you are careful not to damage the door or the seal on the bottom of the door, you can use a flat shovel or similar tool to chip away at the ice.
Rolling sectional overhead garage door spring replacement should cost somewhere between $195 to $300 for a quality set springs (50000 cycle rating). This price will very if the garage door repair company charges a service call fee (trip charge). The most important thing to consider along with price is the quality of the springs and the warranty. There are any company that we use lower or mid quality springs and charge on the higher end because they include a lifetime warranty on the springs. The catch is that this warranty will only covers the spring for life and labor only for 30 days to a year. Look for a company that offers a equal parts and labor warranty. This insures that the warranty represents the rating of the springs that are being installed. For instants, you may buy a 1500 cycle rated spring set (last 3 years +or-) for $200 with a lifetime warranty and 1 year on labor. When a spring brakes after 3 year the spring its self is covered but the labor cost to replace the warranty spring can be between $65 to $100. This can add up over the year as the warranty will not restart at the time of the warranty replacement. On the offer hand, if you purchase a set of springs rated at 50000 cycles (last 10 year +or-) for $270 with a 10 year parts and labor warranty and a spring brakes in 8 years it would be replace at $0 cost. A must batter value! Always check service company review and get the details on the quality of springs a garage door repair company uses and the warranty, part and "labor".

Surprisingly, your garage door just being locked can be causing your problem. Some garage doors have a “full lock” system which enables you, or anybody, to lock your garage door from the outside by only turning the handle. This could mean that anyone in your driveway (children, bystanders) could have turned your handle and mistakenly locked the garage door without you being aware of it. This is an easy fix by realizing this problem and then unlocking your garage door. rong.
After you’ve ordered your new garage door, we’ll perform a site inspection to confirm your door size. We’ll contact you to schedule the installation, and our professional installers will do the rest. They’ll deliver your door, take down the old door, reconnect your opener if there is one, seal your perimeter and provide a final walk-through where they’ll clean up the area and haul away your old door. Additional fees for haul away may apply in some markets. We are happy to provide answers to questions you may have at the time of your garage door and opener installation.

Garage Door Repair Estimates Centennial 80015


Eric Jonas has been writing in small-business advertising and local community newsletters since 1998. Prior to his writing career, he became a licensed level II gas technician and continues to work in the field, also authoring educational newsletters for others in the business. Jonas is currently a graduate student with a Bachelor of Arts in English and rhetoric from McMaster University. https://youtube.com/v/Z_eZc-kh40c
×