Torsion springs are located above the opening of your door with springs that slide onto a bar. Extension spring systems can be found alongside the opening of the door. It's important to know whether or not a garage door company provides service for your needs. Precision's professionally trained technicians are fully equipped to work on torsion and extension spring systems.
In order to prevent injury, garage doors automatically reverse if they come into contact with an obstacle. When the door closes halfway but then reverses for no apparent reason, this may be a sign that there is something preventing it from closing, something that you can't see. Check the tracks for stuff like dirt, rocks, bits of trash, or other debris. Give the tracks a wipe-down to dislodge anything that might be getting in the way.
Many jobs around the house are fairly easy fixes. It’s relatively easy to clean out your fireplace, clean the leaves from the gutters or repaint a wall. It’s a different thing to replace your garage door spring. It’s careful work that is almost impossible to do correctly the first time. Garage door professionals spend a great deal of time learning how to do it properly, and even the most detailed instructions won’t make you an expert in the span of a few hours. It can be almost infuriatingly annoying at times and is simply better left to professionals.
6.8 Properly tightened screws will loosen with less than a turn. Once you loosen a set screw, keep at least one bar in the cone AT ALL TIMES until the spring is fully unwound. Many cones have been over-tightened. The spring may unwind 1/4 turn and not unwind any more until one of the set screws is loosened some more. You may need to completely remove the set screws. The shaft may be distorted and the cone still may not unwind at all.
The following procedures are based on my 30 years in the garage door industry. In spite of my high mechanical aptitude, even after 18 years in the trade I lost the end of my left index finger. A few years later I had five stitches in my right thumb, and a year later five stitches in my left thumb. In 2004 emergency room staffs dug steel out of my eye and sewed up my ring finger with eight stitches. The best I can do is help you minimize the risk of injury; that's all I can do for myself. I am not so naive as to think that I have made my last trip to the emergency room. Repairing garage doors, particularly replacing torsion springs, is dangerous work, whether you are a do-it-yourself homeowner or an experienced technician.

Garage Door Repair Estimates Centennial Colorado 80015


If you use the correct tools and follow our instructions, you can rebuild the entire torsion spring system in just a few hours, without any side trips to the ER. We won't cover how to replace garage door extension spring systems in this story. But we'll show you garage door spring replacement on the more common torsion springs, the kind that mount on a bar above the garage door.
Annual maintenance. Make an annual check of all nuts and bolts on rails and rollers to make sure they’re firmly tightened. Check the condition of all cables to make sure they’re not worn or frayed. Lubricate rollers and springs with a garage-door lubricant (see How to Fix a Noisy Garage Door for maintenance and problem-solving tips). The door should operate smoothly and be properly balanced. Check the balance by disconnecting the opener and lowering the door halfway- the door should hold its position. If it doesn’t, adjust the spring tension or replace the springs.
If the door only goes up six inches and stops, or moves very slowly when using your remote, you could have a broken spring as well. Some customers will notice that the top section of their door is bent or that the door falls very quickly when lowering. Your door may be “crooked” or jerky when going up and down, and both of these signs indicate your torsion spring is in poor condition and very likely to break in the near future. Any time you hear a loud “popping” noise while operating, you should inspect your torsion spring immediately for signs of damage.
My garage door torsion spring broke so I decided to replace it myself. Shipping was next day. I got the torsion spring rod at a local hardware store. Easy to install once I figure out how to lock down the rod from moving and loosening the door cable on the side. Instructions tells you how to do it. Great replacement spring and save $$$ doing it myself.

NEVER use screwdrivers, pin punches or pliers handles to wind or unwind a torsion spring. Trust us: This is the best way to wind up in the hospital. Don't even think about doing this job without a proper set of winding bars. You can buy a set of professional hardened-steel winding bars for about $25 from online suppliers. (Garagedoorpartsusa.com and stardoorparts.com are two online sources that sell winding bars, springs and other parts.) Professional winding bars work with 1/2-in. and 7/16-in. winding cones. If your winding cones have 1/2-in. openings, you can make your own winding bars by cutting a 36-in. length of 1/2-in.-diameter round bar stock in half (buy round bar stock from any hardware or home center). Just file a smooth bevel on each end so it slides into the winding cone holes easier.

The two main garage door operating mechanisms are sectional roll-ups or tilt-ups. Garage door repair services can fix single-car, double-car or RV-height doors. Your garage door may be made of wood, steel, aluminum, masonite, vinyl, fiberglass or another material. The type of garage door repair you need really depends on the type of garage door you have and the issue at hand. Garage door repair pros often charge a flat service call fee to diagnose the problem and provide an estimate. For customers who choose to have the repair done, the service call fee may be applied to the first hour of labor (including time to make the diagnosis). If your garage door is under warranty, the repair may be free of charge.

After working on the car, you find a big oil stain on the driveway. Pulverize a scrap piece of drywall with a hammer (any new home construction site will have dumpsters full of waste pieces of drywall). Crumble the pulverized drywall with your hands and sprinkle on the stain. Leave it overnight, and rinse off in the morning. Reapply and brush in with a bristle broom in cases of stubborn stains.
Homeowners have long been warned that torsion springs are extremely dangerous to work with and that replacing them must be left to a professional. But these claims are somewhat exaggerated. If you understand how they work, and you pay attention to what you're doing, you can replace them safely and surprisingly easily. Granted, they're a little spooky to work with at first (partly due to their reputation), but this is a good thing—you really don't want to forget that they're under tension. Thinking about every step — before you take it — is the key to staying safe.

Garage Door Repair Installation Centennial 80016


4. It is also important to note that extension springs sometimes do not break but rather ‘stretch out’. This is easy to spot as the space between coils when the door is closed is normally consistent. When the spring fails without breaking the space between the coils will become very inconsistent. This condition is quite visible and if it exists the springs should be replaced (Know when to call quits with your garage door). 
A typical version of an overhead garage door used in the past would have been built as a one-piece panel.[1] The panel was mounted on each side with unequal parallelogram style hinge lifting mechanism. Newer versions of overhead garage doors are now generally built from several panels hinged together that roll along a system of tracks guided by rollers.[1] The weight of the door may be 400 lb (181.4 kg) or more, but is balanced by either a torsion spring system or a pair of extension springs.[2] A remote controlled motorized mechanism for opening garage doors adds convenience, safety, and security.[3]
For example, low headroom garage doors often have cable drums on the outside of the end plate and the torsion springs usually wind down rather than up. They normally have left wind springs mounted on the left side of the spring anchor bracket and right wind springs mounted on the right side of the bracket. The first part on the shaft beyond each torsion spring is the end bearing plate. Just beyond the end bearing plate is the cable drum. On these the cable often runs on the front of the cable drum. The bottom of the cable is attached to a bracket that wraps around the front of and outside the vertical track.

"Mile High garage called shortly after submitting my request and set an appointment to have a repair man show up shortly after. They went over everything I needed to get done and gave me several pricing options to fix initial need and alleviate future issues. Work was done in a timely manner and customer service was great. Mile High garage called shortly after submitting my request and set an appointment to have a repair man show up shortly after. They went over everything I needed to get done and gave me several pricing options to fix initial need and alleviate future issues. Work was done in a timely manner and customer service was great. "

Garage Door Repair Guy Centennial Co 80016


Electric Garage Door Openers – Service and repair of the electric garage door opener itself, including the lift mechanism that pulls the door up and guides it down. This is typically not part of the garage door itself and is serviced and repaired on its own interval. Typical service includes inspection, repair, adjustment, and lubrication if needed. Also, we typically inspect the mounting of the unit as well as its attachment to the door itself.


One thing to consider - assuming you have 2 springs and an opener, unless the other spring is quite new, you should replace it at the same time, first because it will probably break fairly soon anyway and changing two is only about $50 more than changing one, and because the springs on both sides should be of equal stiffness - if not, then the door will be unevenly weight compensated and try to open cockeyed, increasing wear and risk of damaging the motor.
2.3 Beware of older winding cones. These older Crawford and McKee torsion spring cones were made for 5/8" bars. Sometimes, however, the holes are too small for 5/8" bars. Whatever you do, don't use a 1/2" bar; instead, grind down a 5/8" bar to fit. I recently had a McKee spring let loose after winding because I used a 1/2" bar when my 5/8" bar wouldn't fit. Just before it let loose I was telling myself, "This is not safe." And it wasn't. The only safe way to replace these older springs is to make a winding bar for each hole of each cone.

Garage Door Repair Emergency Centennial 80016


That sagging garage door is getting harder and harder to open. Garage doors, especially older, wooden models, are as susceptible to the ravages of time and gravity as the rest of us. If your aging doors are a little saggy, square them up with the tension rods positioned on the back of the door. The rods are placed diagonally from top to bottom corners and can be tightened at a turnbuckle to straighten out the door--do a little at time to allow the door to adjust to the change. If your door isn't already equipped with tension rods, you can buy them at home centers.


The winding and unwinding is done at a metal fitting, called a winding cone, attached to the outside end of the spring. You stick a winding bar into one of the four holes in the cone and use the bar as a lever to turn the cone. Once you've completed a quarter turn, insert the other bar into a different hole in the cone and let the bar lever against the closed garage door to hold the spring tension. This allows you to move the original bar to repeat the process, alternating the bars with each quarter-turn. It takes about 30 quarter-turns to fully tension a standard torsion spring.

Vincent was professional, informative, personable, efficient, and cleaned up his work area as he worked. I told him and now I am telling you... He my "Jordan" of garages. Give him a raise or at least a bonus. Thank you for sending him for my install. I am extremely pleased with my garage opener & with his install and information I am confident in its operation. Thank you.
Although garage door springs can break during any season and at any time, they most commonly break during the winter. This has to do with the temperature change. When the temperature sinks below a specific threshold, the metal will contract. This means it’s extremely possible for your door springs to shrink slightly during the winter months. This is hard on the springs and makes them more likely to break. https://youtu.be/Z_eZc-kh40c
×