If you pull the red emergency release rope on your automatic opener and you still can’t lift the garage door, you probably have a broken spring. The counterbalance spring is what lifts the garage door, not the garage door opener. If the spring is broken, the door is dead weight. A garage door can be lifted, but it is going to require some muscle to get it up. It is also important to lift the door evenly so it does not jam in the tracks.
Safe automatic door openers. All automatic openers must now have an auto-reversing mechanism and photoelectric eyes located near the floor on both sides of the door (see photo). If the door is closing and the beam between the eyes is interrupted, the door will automatically reverse. If the eyes aren’t connected, the door won’t operate. For instructions on how to install a new garage door opener, see How to Install a Garage Door Opener.
Garage door springs don’t require extensive care and maintenance. However, they also can’t be left entirely to their own devices. Spraying the springs with WD-40 is a good place to start. It’s also a good idea to check the balance of the garage door every year. To do this, simply lift the garage door up about halfway and let go. If the springs are in good working condition, the door should remain still. If the springs are beginning to weaken, the door might sag or fall. By taking these basic steps, you can preserve your door springs for longer.
CAUTION! Replacing garage door torsion springs is dangerous because the springs are under tension. If you do not use the right tools and follow safe procedures, you could lose hands, limbs or even your life. You could also damage property. We want your business, but not at the expense of your well being. Doing the job right is your responsibility. If you have any doubts about your ability to safely change your springs, we recommend you hire a professional to repair your garage door. Safety First! Then work.

Garage Door Repair Emergency Centennial Colorado


If you have two torsion springs on your garage door, the good spring will most likely keep the cables on the drums when the other spring breaks. This makes it much easier to lift because the good spring will be pulling half the weight of the garage door. You can also use the garage door opener to help assist while someone lifts the door and acts as the broken spring. Use extreme caution when doing this to prevent damage to your garage door or injury to a person.
When a torsion spring is wound up, it grows 2” in length. This is because the spring starts to compress and the metal has to go somewhere. After the spring is wound, the winding cone is clamped down on the torsion shaft so it can turn the drums to wind the cables as the door goes up. Since the end of the spring is “set” on the shaft, a two-inch gap is left when the spring break's. This is the most definite way of determining you have a broken garage door spring. https://www.youtube.com/v/Z_eZc-kh40c&feature=youtu.be
Instead, try other methods that might break the frozen connection between the door and the floor. For example, you can use a heat gun or hair dryer to melt the ice and free the door. Standard de-icing products can also work. And if you are careful not to damage the door or the seal on the bottom of the door, you can use a flat shovel or similar tool to chip away at the ice.

Garage Door Repair Guy Centennial Colorado 80016


Garage door springs support most of the weight of the door when it's opening and closing. A broken spring typically will make the door very hard to lift, rather than causing the door to stick halfway. But some spring problems can contribute to a stuck door. The springs help turn metal wheels, called pulleys, that help lift the door via vertical cables at each side of the door. A pulley can become jammed by an obstruction or possibly a misaligned or hung-up cable. Any problems with springs or pulley should be examined by a garage door professional. Springs (and pulleys) are highly tensioned and can be very dangerous to work with.

When a spring breaks on a garage door an immense amount of energy being displaced. Torsion springs are mounted over the garage door and they have a shaft running through the middle. When they break, the spring unwinds in less than a second and creates a loud noise due to the coils spinning on the shaft. Based on customer feedback, it can be quite startling. http://m.youtube.com/watch?v=Z_eZc-kh40c

Start your garage door spring replacement project by getting a rough measurement of your springs (length and diameter). Then measure the width and height of your door. Make sure the quote includes the trip charge, parts and labor. Then ask for a price based on 7x19 lift cables and double-life springs. Those items will give you more years of service and should only add $65 to the price.

Garage Door Repair Guy Centennial Co


Jerrod the technician had answers to all my questions. He was very knowledgeable and very patiently explained what was going on with my garage door and the opener. I would definitely recommend A1 garage door service to friends and family. I was given options to either repair the door or replace it. I will get the door replaced when it gets non-functional from A1 garage door service.

Garage Door Repair How Much Centennial 80016


However, if you lose power and use the disconnect switch, you’ll need to reattach it to use your garage door motor to open and close your door again. Open the door all the way and then reattach this hook. Then try opening or closing the door again with your transmitter, and you should be all set. It will be easiest to reattach this hook when your car is not in the garage, as you’ll need to place a step ladder underneath the motor to reach it.
The garage door opens and closes many times throughout the year, and something may blow inside. While it is usually something such as loose leaves or small amounts of dirt, the rails that the door travel along can collect this loose debris. Over time, the buildup of debris creates a blockage on the rails. Note where on the rails the door is stuck and clean that area. If children use the garage to leave the house, it's sometimes something as simple as a small, bouncing ball that happens to land in just the right -- or wrong -- spot.

Asap Garage Door Repair Centennial Co 80016


Unlike torsion springs, replacing extension springs has long been given the "green light" for DIYers, primarily because you can complete the job without having to deal with spring tension. The general process is simple and safe: open the door to relieve the spring tension (and secure it open with C-clamps in the tracks); disconnect the spring from the track bracket and the spring pulley, and disconnect the safety cable from one end; install the new spring, reinstall the pulley, and reconnect the safety cable, and you're done.
Check your garage door rollers to see if they have come off their tracks. If no damage has been done, a tech should be able to easily place them back on. If the track has become bent, however, it must be repaired and possibly (depending on the amount of damage) replaced. Don’t operate your door if it's off track or your track is bent. Your door could become seriously damaged.
Good response time and service; Question - I googled to find the Sears Garage Door repair phone number. During the conversation, I was unsure if this was "Sears" or a "contractor service" or other service. I had to ask if this repair person was coming from "Sears" or an independent repair. I was concerned until the service man arrived in a sears truck wearing Sears apparel. You might want the process to be more clearly identified as Sears.
6.4 Test the fit of the bar in the cone before loosening a set screw. Insert one end of your winding bar into one of the holes of the winding cone. Pull down on the bar slightly to make sure the set screws are tight. Position your ruler between the bar and the garage door. Move the bottom of the bar from side to side and measure the play. It should be less than an inch and a half. If it is over 2" either get someone else to change your springs or have someone make some bars that will properly fit the cones.
10.2 Tape your winding bars if you have not done so already, not only to assure that you are inserting the bars completely into the cones as you wind the torsion springs, but more importantly to assure that the bar does not slip out of the cone when you stretch the springs at the end. This has happened to me several times. Professionals always stretch torsion springs after winding them because the shaft floats horizontally between the flexible end bearing plates as the door operates. Although this may be as little as 1/4", the binding of the coils as the garage door closes oftentimes keeps the door from closing completely, especially when the torsion springs and bearings are dry.
Usually, when a garage door spring breaks the door has already closed or come down. In some instances, however, a spring can snap while the door is closing or in motion, causing the door to fall rapidly. In these situations, the door can become a safety concern for you and your family, so you should keep your distance and call a garage door professional as soon as possible. Garage doors are very heavy and can cause injury if not handled properly. When a garage door problem occurs, call a Sears Garage Door expert to help. http://www.youtube.com/e/Z_eZc-kh40c?app=desktop
A standard double garage door is 7 ft. high by 16 ft. wide. Standard single doors are 7 ft. high by 8 or 9 ft. wide. Because the doors are so large, few home centers and only some garage door stores keep many doors in stock, so expect to order one instead of buying it off the shelf. Garage doors are available in wood, fiberglass and steel. Steel doors, like ours, are light, maintenance-free, affordable, readily available, and have an insulating value as high as R-19.

I have 2 full house humidifiers that have stopped functioning right. There are new filters, fan runs, tanks are full of water but they are not empting into the base. They have worked for part of the winter and now nothing seems to help...I loosened the caps thinking I had them too tight..... nothing seems to work .I have had humidifiers for 20 years and this is the first time this has happened to me. The humidifiers are only 2 years old. Any suggestions??
2. These springs do wear out over time – in fact, they are commonly rated with what is called a cycle life. The average standard cycle life is ten thousand cycles with each cycle being one opening and closing of the door. This means for a door that sees four cycles per day you might expect to replace your springs after somewhere close to seven years of use.
When you hire a professional, the first thing they will do is turn off the power as a safety precaution.  They will then measure the existing door springs to make sure the new springs they order or have in stock fit accordingly.  With these new springs, they will unwind the existing springs and install the new ones in its place, tightening them with screws.  When tightened, the springs will be balanced, lubricated and the springs will be wound up.  Lastly, the door will be tested and the tracks will be lubricated to move efficiently.
We have had many concerns with our garage opener unit both safety issue and sleepless nights. At this time we are pleased that so far the unit is operating as it should.Hopefully we hope the issue of the unit opening by it self at early morning hours is solved. And if this is so, we want to Thank all involve in bring a satisfactory solution to this nightmare.
Sometimes, you’ll notice that your garage door closes all the way and then immediately goes back up instead of staying in the closed position. This issue usually arises with brand new garage doors that were just installed or older models that may need to be reset. If this happens, the most likely culprit is the open and close limit settings of your garage door opener.
Measure area labeled headroom (5), which is the distance between the top of the door opening (jamb header) and the ceiling (or floor joist). 10" is required for the standard extension spring or EZ-SET® Extension Spring System while 12" is required for a standard torsion spring and EZ-SET® Torsion Spring System. If you have restricted headroom, special hardware is available. Additional headroom is required for installation of an automatic garage door opener. NOTE: If garage door height extends above the opening, the headroom measurement should be adjusted proportionately.

For Sears Garage Door Installation and Repair Services, making your garage door safe is as important as making it function well. For this reason, all of our repair services and tune-ups feature a 20-point safety check. Our technician will carefully examine your garage door panels, springs, sensors, safety release, hardware, track, and more. This ensures that, not only has our work been done well, but that your garage door poses no danger to your vehicles or family. Due to the intricacy of garage door systems, only garage service professionals should attempt to adjust, repair, or service door equipment.

When a torsion spring is wound up, it grows 2” in length. This is because the spring starts to compress and the metal has to go somewhere. After the spring is wound, the winding cone is clamped down on the torsion shaft so it can turn the drums to wind the cables as the door goes up. Since the end of the spring is “set” on the shaft, a two-inch gap is left when the spring break's. This is the most definite way of determining you have a broken garage door spring. 

Garage Door Repair Near Me Centennial Colorado


The garage we take for granted very likely stores thousands of dollars worth of tools and household belongings, not to mention your automobiles. Yet this space is typically rather easy for intruders to penetrate. Garage security can be greatly improved by installing a modern garage door opener that features rotating digital codes, which can foil even the most tech-savvy prowlers.
Replacement spring procedure took me exactly 1 hours including preparation and clean-up for double aluminum garage door. Watch the DIY video on Youtube, save $$, be careful with winding the torsion springs. Rule of thumb: 7' height door garage= 7' x 4 (each 1/4 turn) + 1 = 29 turns (1/4 turn), 8' height door garage = 8' x 4 + 1 = 33 turns (1/4 turn), and so on....
Garage door manufacturers typically produce garage doors fitted with torsion springs that provide a minimum of 10,000 to 15,000 cycles and are guaranteed for three to seven years. One cycle is a single opening and closing sequence. Most manufacturers offer a 30,000 cycle spring. However, it is important to remember that if the weight of the garage door is increased by adding glass, additional insulation, or even several coats of paint, the life of the torsion spring may be greatly reduced. Additionally, springs at highly humid environments, such as coastal regions tend to have a significantly shorter cycle life, due to the corrosive cracking.
10.4 Raise the second bar 90 degrees and insert the first bar. This is "three." Continue winding. If the spring shortens in length, unwind the spring and switch sides - the springs are on backward. Otherwise, continue winding until you reach a count of "30." This is 7 1/2 turns, which is normal for most 7' doors. Longer life springs are wound the same number of turns. Newer steel doors with only one strut on top often need only 7 1/4 turns. On 8' doors count to 34. Each time you insert a bar into the winding cone, listen for the click to let you know the bar is in all the way. Not inserting the bar all the way could cause the cone to explode.
With Garage Door Doctor, you can rest assured we will replace your springs correctly. We offer 2 types of springs – standard and high cycle. On a 7 foot tall door, our standard torsion springs will last 15,000 cycles and our high cycle torsion springs will last 50,000 cycles. How many years will this last you? That is based off only one thing – usage. For example, with standard torsion spring, if you use your door 4 times a day, you get just over 10 years of life. However, if you use your door 8 times a day, you would get just over 5 years of life. If you use door very little or if you are moving very soon, maybe standard springs would be best for you. If you use your door many times a day or if you don’t plan on moving for a while, high cycle springs would be best for you. Getting high cycle springs will ensure you won’t be stuck with a broken spring for many years to come. Either way, both types of torsion springs we offer work great – its just a matter of when the break again. Call Garage Door Doctor today to have your garage fixed properly!
Extension spring systems should always be restrained by a safety cable that runs through the middle of the spring, tying off to a solid point at the rear and front of the horizontal door track. Extension springs represent a hazard to bystanders when a spring, pulley, or cable breaks under tension. Metal parts from extension spring systems can suddenly be launched.
On our EZ-Set Torsion Springs page you will find several options for replacing these springs. We also have step by step instructions for EZ-Set Torsion Spring Replacement. In addition, one of our customers has provided excellent EZ-Set Torsion System instructions for removing the spring without wrecking the winding unit that secures the stationary cone. Instead of a spanner tool, you may prefer to use a pipe wrench or large channel locks to hook the end of the spring and remove it from the cones in the last step.

Garage Door Repair And Installation Centennial Co 80015


9.14 Slide the springs to the bracket. Double-check to make sure you have the right wound spring on the left side and the left wind spring on the right side. Turn the springs until the ends are facing you. The wire at the ends of both torsion springs here at the bracket should be pointing down. At the winding cones at the opposite ends, the spring wire points up. If not, reverse the springs. About once a month we get a phone call from a do-it-yourself customer who begins the conversation with, "I wound the garage door spring to about six turns and the spring came loose from the cone." We normally refer them back to this step and suggest they switch their springs.
9.8 Twist the garage door shaft to tighten the cable on the drum. While twisting, vise grip the shaft as shown to keep the cable tight on the drum. The top of the vise grip should be tight against the garage header. This will keep the cable snug on the first drum while you install the cable on the other drum and position it in place. It also keeps the shaft from turning and the cables peeling off when you wind the springs. That one grip can save many hours of walking back and forth and having to level and re-level the garage door after winding the torsion springs.
Loosen the set screws while holding each spring with a winding bar. Position a sturdy ladder to the side of the springs, rather than working directly in front of them, for safety reasons. Put on eye protection and leather gloves. Push a winding bar into the bottom hole of the winding cone on the outside of 1 spring. Use a wrench to loosen the 2 set screws. Keep a firm grip on the bar as the the spring will expand powerfully as the screws are released. Repeat on the other side.[2]
There are many steps to replacing torsion springs, but overall it's a simple, straightforward process. If you're inclined to attempt it, find a good online video tutorial (preferably done by a garage door pro) that walks you through the entire process, including how to buy the right size of springs. You can also buy new springs and any related parts online, along with the most important items that you need: the two solid-metal winding rods that you use to wind and unwind the torsion springs.
Get a price quote on a New Garage Door- Use our super-simple garage door designer to learn about the available options, pick the ones you like best, and send it to us for a free quote. It's the fastest way to shop for a garage door on the web. In less than 10 minutes, you'll have a much better idea what you want and get a price without sales pressure. Click garage door designer to get started...
A typical version of an overhead garage door used in the past would have been built as a one-piece panel.[1] The panel was mounted on each side with unequal parallelogram style hinge lifting mechanism. Newer versions of overhead garage doors are now generally built from several panels hinged together that roll along a system of tracks guided by rollers.[1] The weight of the door may be 400 lb (181.4 kg) or more, but is balanced by either a torsion spring system or a pair of extension springs.[2] A remote controlled motorized mechanism for opening garage doors adds convenience, safety, and security.[3]

Garage Door Repair In My Area Centennial Colorado 80015


I really think that bill was way to much.I had I stalled new door springs with the help of a friend but tube door didn't. want to open .that's why I called sears so the man that came to my house spent about 15 minutes working all that be did was remove the new springs saying they were the wrong springs and put the old springs back on that's all he did .
9.4 Slide the end of the shaft into the end bearing plate. Tighten the set screws an additional 1/4 to 1/2 turns beyond the point you finger-tightened them. Add an additional 1/4 turn if you could not find the original set screw indentations in the previous step. Heavier wooden garage doors may require an additional 1/4 turn. Caution: Under-tightening the drums could cause the drum to slip and the door to cock or fall. Over-tightening the set screws could damage the shaft or drum, resulting in the same problems. This is a critical step.
An extension spring counterbalance system consists of a pair of stretched springs running parallel to the horizontal tracks. The springs lift the door through a system of pulleys and counterbalance cables running from the bottom corner brackets through the pulleys. When the door is raised, the springs contract, thus lifting the door as the tension is released. Typically these springs are made of 11 gauge galvanized steel, and the lengths of these springs are based on the height of the garage door in question. Their lifting weight capacity can best be identified by the color that is painted on the ends of the springs.
As mentioned, the only time you should attempt to open a garage door with a broken torsion spring is during an emergency. Otherwise, you should contact a service technician for emergency repairs. We provide same-day garage door service for people just like you who find themselves stuck and unable to move due to a faulty torsion spring. For prompt, reliable service any time of the day or night, please contact us.
As a first time homeowner, Home advisors is an invaluable tool! There is a steep learning curve that comes with buying a house!!!! Being able to have access to unbiased information is great! It really helps to have a basic idea of what costs are, and all the different things that go into each project. who knew that there was so much to consider when looking to replace garage doors!!!!
9.4 Slide the end of the shaft into the end bearing plate. Tighten the set screws an additional 1/4 to 1/2 turns beyond the point you finger-tightened them. Add an additional 1/4 turn if you could not find the original set screw indentations in the previous step. Heavier wooden garage doors may require an additional 1/4 turn. Caution: Under-tightening the drums could cause the drum to slip and the door to cock or fall. Over-tightening the set screws could damage the shaft or drum, resulting in the same problems. This is a critical step.
Measure area labeled headroom (5), which is the distance between the top of the door opening (jamb header) and the ceiling (or floor joist). 10" is required for the standard extension spring or EZ-SET® Extension Spring System while 12" is required for a standard torsion spring and EZ-SET® Torsion Spring System. If you have restricted headroom, special hardware is available. Additional headroom is required for installation of an automatic garage door opener. NOTE: If garage door height extends above the opening, the headroom measurement should be adjusted proportionately.
It's a great idea to hire a professional to do your garage door opener installation for a few reasons. First of all, a pro can often be the most time-efficient way to handle the garage door opener installation, because a pro will have the right tools and experience to make your garage door opener installation as swift and smooth as possible. Secondly, a pro garage door opener installation will include making sure all the required garage door opener mounts and sensors are put together properly. A great garage door opener installation will include using the manufacturer’s recommended method of assembly and optimal placement of the garage door opener mount and sensors. Find top-notch garage door opener installation pros on Amazon Home Services and you'll see professional garage door opener installation services at competitive prices. Secure convenience and peace of mind by getting a professional garage door opener installation for your home. You'll never regret adding a garage door opener installation project to your to-do list. If you’re the kind of person who doesn’t have the time or patience to do your garage door opener installation, don’t worry. Because you don’t have to if you don’t want to. Amazon Home Services has you covered, to do your garage door opener installation quickly and professionally. Just schedule the garage door opener installation pro of your choice from our list of top-rated service providers.
Aging garage door springs cause the door to effectively "weigh" more as the steel loses its resiliency. With new springs, a heavy garage door should take no more than about 10 pounds of force to lift into an open position. With springs nearing the end of their lifespan, the force required to lift the door can be considerably more, since a garage door may weigh 200 pounds or more.

Action Garage Door Repair Centennial Colorado 80015


While it would be wonderful if door springs lasted forever, the reality is that the simple act of opening and shutting the door multiple times every day isn’t easy. It’s hard on the springs, even though they’re built to do it. Most springs will last for a while, but they won’t last forever. The regular wear and tear of endlessly opening and shutting the door breaks them down and eventually, they’ll need to be replaced.

Garage Door Repair Free Estimate Centennial Co


If your torsion spring isn’t lifting your door or your door is stuck, it is best to not attempt fixing it on your own. Garage doors are very heavy and can be the source of great injury if not handled with care when a part is broken. At Advanced Garage Door Solutions, Inc., we are there for you to quickly fix the problem so that normal garage door function is restored. To learn more, call the Minneapolis office at 952-500-3921 or the St. Paul office at 651-769-7191 and request a free estimate.

Garage Door Repair And Service Centennial Co 80015


An extension spring counterbalance system consists of a pair of stretched springs running parallel to the horizontal tracks. The springs lift the door through a system of pulleys and counterbalance cables running from the bottom corner brackets through the pulleys. When the door is raised, the springs contract, thus lifting the door as the tension is released. Typically these springs are made of 11 gauge galvanized steel, and the lengths of these springs are based on the height of the garage door in question. Their lifting weight capacity can best be identified by the color that is painted on the ends of the springs.
For Sears Garage Door Installation and Repair Services, making your garage door safe is as important as making it function well. For this reason, all of our repair services and tune-ups feature a 20-point safety check. Our technician will carefully examine your garage door panels, springs, sensors, safety release, hardware, track, and more. This ensures that, not only has our work been done well, but that your garage door poses no danger to your vehicles or family. Due to the intricacy of garage door systems, only garage service professionals should attempt to adjust, repair, or service door equipment.
If you haven’t looked at garage doors lately, prepare to be pleasantly surprised. We’ve taken the garage door and made it stylish with designs to complement both classic and contemporary homes while still keeping the functionality you desire. A garage door can represent more than 30% of your home’s curb appeal, which makes choosing the right design especially important – and Home Depot has the widest selection available. With over 1,000 different garage door designs in wood, steel, composite, aluminum and glass, you’re sure to find the perfect style to transform your garage… and your home.
To realign the track, first loosen the screws that hold the track to the frame. Then, gently tap the track with a rubber mallet to move it back into the proper position. Use a level to ensure it’s perfectly straight. Once you have the alignment correct, tighten the screws securely to ensure the track won’t move and cause more issues when opening your garage door. You’ll need to repeat this same process on the other tracks as well, as these may also be out of alignment.
Traditional One Panel: These doors consist of one large panel which tilts to open by employing a spring mechanism to swing upward. The wood version is popular in the South and Southeastern US, where a milder climate keeps the wood from rapidly deteriorating. Traditional garage door designs include Cape, Colonial, Ranch, Tudor and Craftsman. The disadvantage is these doors require a lot of clearance to operate correctly. Sometimes repairs can be difficult because of the heaviness of the door or its inaccessibility. Average cost to repair tilt-up doors is $172.
Containment cables. When old extension springs break, the springs and cables become heavy whips that damage cars and even injure people. To solve the whipping problem, manufacturers now offer containment cables that run through the center of side-mounted extension springs. If you have extension springs and don’t plan to replace your door, make sure the springs have these containment cables, or have a professional install them.
9.16 If you cannot get the stationary cones to finger-tighten against the center bracket, we recommend installing washers between the winding cone that houses the bearing and the spring bracket. This is a common problem with torsion springs on older Windsor garage doors because their steel bearings are often wider and they extend beyond the stationary cone. Raynor garage doors also have wider bearings that fit properly in their 2 1/4" stationary cones, but washers may need to be installed if their bearings are installed in 1 3/4" or 2" stationary cones, or if some of their older bearings are installed in their newer cones that are installed on older brackets.

Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring. 

Garage Door Repair Bracket Centennial Colorado 80016


Looking to repair your garage door opener? Common problems could range from issues with the remote or wall switch that control the garage door opener to more serious issues like a grinding noise coming from the opener itself. If you need help with repairing your garage opener, schedule a repair appointment today! We repair all major brands and have same-day availability in most markets, so we can get your garage door opener repaired and running smoothly. To learn more about the cost of repairing garage doors, visit our garage door and opener installation and repair cost guide.
When I called to schedule the repair service, I was transferrd 5 times and spoke with 6 service reps. Each rep was very confused by my request to get my garage door repaired. One rep actually told me that Sears doesn't repair garage doors. I had to tell her that Sears installed the door. When I finally found a rep who could schedule my service, it took one week for the appointment. https://www.youtube.com/watch?v=Z_eZc-kh40c&feature=youtube_gdata
Garage door springs come in two styles: torsion (see above), which mounts on the header above the door, and extension (Photo 1), which floats above the upper roller track. In the past, extension springs were safer to install but didn’t have containment cables running through the center of the spring. Without cable, these springs become dangerous, heavy whips when they break. They also tend to be noisier than torsion springs, and we recommend you use them only if you don’t have the 12 in. of headroom above the door that a torsion spring requires. https://youtube.com/watch?v=Z_eZc-kh40c&app=desktop
×