One thing to consider - assuming you have 2 springs and an opener, unless the other spring is quite new, you should replace it at the same time, first because it will probably break fairly soon anyway and changing two is only about $50 more than changing one, and because the springs on both sides should be of equal stiffness - if not, then the door will be unevenly weight compensated and try to open cockeyed, increasing wear and risk of damaging the motor.
Every thing the tech demostrated was helpful, he knew how to do his job even if his eyes were shut. Very knowledgeable, took time out to explain every detail about the install process. Very highly satisfied. A d would love to have him for future additional repairs. Would definitely recommend sears and would use you guys again thanks mr.technician for a job well done.
9.4 Slide the end of the shaft into the end bearing plate. Tighten the set screws an additional 1/4 to 1/2 turns beyond the point you finger-tightened them. Add an additional 1/4 turn if you could not find the original set screw indentations in the previous step. Heavier wooden garage doors may require an additional 1/4 turn. Caution: Under-tightening the drums could cause the drum to slip and the door to cock or fall. Over-tightening the set screws could damage the shaft or drum, resulting in the same problems. This is a critical step.
If you have two torsion springs on your garage door, the good spring will most likely keep the cables on the drums when the other spring breaks. This makes it much easier to lift because the good spring will be pulling half the weight of the garage door. You can also use the garage door opener to help assist while someone lifts the door and acts as the broken spring. Use extreme caution when doing this to prevent damage to your garage door or injury to a person.
I really think that bill was way to much.I had I stalled new door springs with the help of a friend but tube door didn't. want to open .that's why I called sears so the man that came to my house spent about 15 minutes working all that be did was remove the new springs saying they were the wrong springs and put the old springs back on that's all he did .
Chris was very professional & thorough. He arrived on time & was able to answer all questions that I had. I was extremely satisfied with the quality of the work he performed. I spoke several times on the phone with Mrs. Carol who keep me informed prior to, during, and after the installation of my garage door. She was very professional, easy to talk with and resolved any misunderstanding that I had.
These instructions were first posted in 2005, and they were updated in August of 2008. I have been frank about the hazards of garage door repairs and about my own accidents incurred while replacing torsion springs. For what it's worth, you might be surprised to know that I, too, have benefitted from producing these instructions. I have not had any garage door accidents since we first published these on the web in 2005. And, in as much as I have helped keep other DIY-ers out of the emergency room, I consider myself somewhat of a medical practitioner.
Asap Garage Door Repair Centennial Co
We have had many concerns with our garage opener unit both safety issue and sleepless nights. At this time we are pleased that so far the unit is operating as it should.Hopefully we hope the issue of the unit opening by it self at early morning hours is solved. And if this is so, we want to Thank all involve in bring a satisfactory solution to this nightmare.
If one of your door springs just broke and you are looking for instructions to decide if you can change the spring or springs safely and correctly, this page should help. DO NOT OPEN AND CLOSE YOUR GARAGE DOOR. Wooden garage doors are heavy and will probably damage or ruin the opener. The tops of steel doors often bend when operated with broken springs.
Replacing torsion springs is done with the door closed. You start by carefully unloading all of the springs (most standard-size doors have two; any broken spring will already be unloaded), using the winding bars. Then, you unbolt the springs from the central rod bracket, disconnect the cables from the pulleys, and loosen the pulleys and slide them off of the rod. Next, you swap out the springs, reinstall the pulleys and cables, and secure the inside ends of the springs to the central bracket. Finally, you wind up both springs (securing them with two setscrew bolts on the winding cones) and test the door for proper spring tension. Often, springs need an extra quarter-turn or two to get the door balance just right.
Ace Garage Door Repair Centennial Colorado 80016
"Our garage door wouldn’t shut on sunny days and the tech came out. He explained my options (swap the “seeing” sensor with the other, or replace them). He tried swapping and it was still an issue so he replaced them. In addition, he adjusted the spring because the company that installed it last year did not adjust it properly. He was here for about two hours and charged us for only the sensor replacement. Will definitely be using this company again! Highly recommend them. "
Typically, it will cost less to install a steel garage door without an opener than to install a custom wood door with a garage door opener. Recent innovations have also yielded high-tech doors with thick insulation and energy-efficient glaze, as well as finished interior surfaces and other significant upgrades. These are more expensive doors, but they are also extremely durable. http://www.youtube.com/watch?v=Z_eZc-kh40c&feature=youtube_gdata
For a scholarly introduction to torsion springs and for more information on how to install them I recommend you visit Richard Kinch's page, "How I Replaced Deadly Garage Door Torsion Springs and Lived to Tell the Tale." Richard is a brilliant engineer who has provided a wealth of technical information on fixing torsion springs along with valuable advice regarding some of the schemes unscrupulous garage door companies use to rip people off.
Lewis did a great job and not only met my expectations but blew them away. His attention to detail was impressive. He reolaced the springs on my two car garage door and he went out of his way to adjust the tension on my second single car garage door to make it open better. He also recommended replacement of the rollers on my main garage door as they were getting pretty worn out and making some noise. He was very friendly and personable. Was willing to explain what he was doing so we could learn something too. I would recommend Lewis Nagy if you are in his area here in Apollo Beach/Riverview. Thanks again!
Garage Door Repair Companies Centennial Co 80015
Sometimes, people unplug their power source and then wonder why their garage door opener fails to work. Sounds ridiculous, I know, but it does happen. Make sure that your garage door opener is plugged into a working outlet. Outlets sometimes go out without warning, so you can check to see if the outlet is working by plugging another working electronic device into it. Also, check your circuit breaker, fuse, or GFCI.
We look out for the safety of our customers and their families. That’s why we do not sell garage door torsion springs separately to consumers, and it’s also why we recommend putting your broken garage door in the hands of our experienced technicians. At Garage Door Medics, we are licensed, bonded, and insured. We have completed thousands of garage door installations and spring repairs, and we make sure they are done safely and with the right springs for your garage door system.
Garage Door Repair Free Estimate Near Me Centennial Colorado
Does your garage door seem to be jammed? There are several reasons this could have happened. The answer may be simple and easy to fix, or there may be a larger underlying problem with your garage door system that requires an expert to repair. Run through the following list to determine if it's a problem you can fix on your own or if you should call a professional garage door technician to repair it for you.
If you use the correct tools and follow our instructions, you can rebuild the entire torsion spring system in just a few hours, without any side trips to the ER. We won't cover how to replace garage door extension spring systems in this story. But we'll show you garage door spring replacement on the more common torsion springs, the kind that mount on a bar above the garage door.
If your garage door track is out of alignment, it can be a serious issue. The metal track your door runs on needs to be aligned properly in order for your door to move. If you see gaps between the rollers and rail, or bends in the rails themselves, you have a problem. The heavy weight of the door can compound these issues and make them worse until it becomes dangerous to operate your door.
Sears Craftsman Garage Door Openers are America’s favorite. We have several options to choose from that will fit your individual needs. Sears garage door opener selections includes 1/2 horsepower, 3/4 horsepower, belt and chain drive as well as the Craftsman Smart Control garage door opener which allows you to control and monitor your garage door even when you are away from home. https://m.youtube.com/v/Z_eZc-kh40c