After you’ve ordered your new garage door, we’ll perform a site inspection to confirm your door size. We’ll contact you to schedule the installation, and our professional installers will do the rest. They’ll deliver your door, take down the old door, reconnect your opener if there is one, seal your perimeter and provide a final walk-through where they’ll clean up the area and haul away your old door. Additional fees for haul away may apply in some markets. We are happy to provide answers to questions you may have at the time of your garage door and opener installation.
Overhead garage doors weigh hundreds of pounds, and doors that are not properly maintained or which are equipped with older automatic garage door openers can be safety time bombs. All too common are the tragic stories of garage doors injuring or even killing children or pets who found themselves underneath a closing door. Modern automatic door openers with auto-stop and auto-reverse mechanisms have greatly reduced such accidents, but mishaps can still occur if the door and door opener are not properly maintained. http://www.youtube.com/watch?feature=youtube.be&v=Z_eZc-kh40c
If your garage door goes up and down in a jerky motion, you might have one broken spring on a two spring system. Some garage door openers are strong enough to lift a door with only one good spring. The “herky jerky” motion is especially common with garage doors equipped with extension springs. It might be something as simple as lubricating your garage door pulleys, hinges, and rollers. When in doubt or if something doesn’t feel right about your door, call a service company to have it serviced.

Garage Door Repair Free Quote Centennial 80016


If you have a Wayne Dalton TorqueMaster system (pictured below), the springs will be inside a tube. The only way to determine if one is broken is to lift the garage door manually. If the door is heavy (roughly 60lbs for a double car door), you most likely have a broken spring inside the TorqueMaster tube. Another way to tell if you have a broken spring in your Wayne Dalton Torquemaster tube is if the door goes up and won't go back down.
Your door’s torsion spring is located approximately one foot from the top section of your door when it is closed. It consists of two large coil springs, and is approximately the length of your arm. Its purpose is to balance the weight of your door so that a door weighing between 160 and 185 pounds is practically weightless to lift. As such, it makes it possible for a garage door opener to raise the door using only ten pounds of pressure.
Loosen the set screws while holding each spring with a winding bar. Position a sturdy ladder to the side of the springs, rather than working directly in front of them, for safety reasons. Put on eye protection and leather gloves. Push a winding bar into the bottom hole of the winding cone on the outside of 1 spring. Use a wrench to loosen the 2 set screws. Keep a firm grip on the bar as the the spring will expand powerfully as the screws are released. Repeat on the other side.[2]
6.4 Test the fit of the bar in the cone before loosening a set screw. Insert one end of your winding bar into one of the holes of the winding cone. Pull down on the bar slightly to make sure the set screws are tight. Position your ruler between the bar and the garage door. Move the bottom of the bar from side to side and measure the play. It should be less than an inch and a half. If it is over 2" either get someone else to change your springs or have someone make some bars that will properly fit the cones.

Garage Door Repair Free Quote Centennial Colorado


However, when a car is trapped inside, then it must be opened; otherwise, taking a cab or bus would be the only option left. Opening it would require help from another adult person or should be done by technicians. And every attempt in opening it, safety precautions should always be the first thing in mind. Never rely on garage entry openers when the spring is broken since it can cause falls and accidents. If the homeowner is not confident to open it or has no time to do it, it is always wise to call a technician.

Given the complexity of a garage door and opener system, there are a variety of different areas something could go wrong. If your garage door shakes or is very loud during operation, the garage door closes all the way only to immediately open back up, the garage door opens slowly or closes too quickly, or the garage door opener and remote aren't working at all, you should seek help from a professional garage door repair specialist.

Fiberglass and vinyl garage doors are composite units, combining a steel core behind a fiberglass or vinyl skin. They have also polyurethane insulated base sections, or other type of foam insulation. These premium doors can match steel garage doors, and be a realistic imitation of wood (namely fiberglass units), but they may be more expensive than steel units.
3. On an extension, or stretch type spring there is little you can do to extend the service life. On a torsion spring (the type that is wound on a bar rather than stretching out) you can help ensure a full cycle life by lightly lubricating the coils of the spring to reduce friction. If your garage door sees a lot of use and spring failure is an ongoing concern it can be addressed by selecting extended cycle springs. Discuss this upgrade when calling in for spring service, your service advisor will assist in making the correct choice for your needs.
To install a single new garage door it should cost between $500 and $800. They demonstrate that the average homeowner can usually tackle such a project in a nine hour time span and a professional will be able to complete it in roughly five hours. Should it be a DIY project? Not really, most housing experts point out that it is a two-person job, requires advanced carpentry skills, and even knowledge of household electronic systems.
Examine the garge door rollers, hinges, tracks, and other hardware for signs of damage that might cause the door to hang up. Lubricate the tracks and hardware with silicone spray or oil. Raise the door slowly, watching it as it lifts. See if it catches on a warped panel or support beam or if an obstruction in the path of the photo eye causes it to stop or reverse. Any part that protrudes into the path of the garage door can cause it to stop.
A garage door with a broken torsion spring can fall rapidly and cause injury or death. However, the most common danger comes when your torsion springs break and you decide to undertake the repair/replace them yourself. Torsion springs can be very dangerous, and you not only need the exact tools for the job, but also need to have a good knowledge of the mechanics involved. Some of the parts involved in such a process can be life threatening, and must be handled with care and precision, which is why it is always recommended that you call in a professional, rather than trying to handle a replacement or repair by yourself. Failure to do so may leave you with injuries and/or damage to your property.
9.4 Slide the end of the shaft into the end bearing plate. Tighten the set screws an additional 1/4 to 1/2 turns beyond the point you finger-tightened them. Add an additional 1/4 turn if you could not find the original set screw indentations in the previous step. Heavier wooden garage doors may require an additional 1/4 turn. Caution: Under-tightening the drums could cause the drum to slip and the door to cock or fall. Over-tightening the set screws could damage the shaft or drum, resulting in the same problems. This is a critical step.
If you use the correct tools and follow our instructions, you can rebuild the entire torsion spring system in just a few hours, without any side trips to the ER. We won't cover how to replace garage door extension spring systems in this story. But we'll show you garage door spring replacement on the more common torsion springs, the kind that mount on a bar above the garage door.
7.5 Slide both springs out toward the cable drums. This is often the hardest part of the job. You may need to file away swollen shaft, set screw burs, drywall or paint. If the shaft is distorted because the garage door installer overtightened the set screws, file the shaft, insert a bar into the cone and tap the bar with a hammer until the cone passes over the enlarged portion of shaft.
9.9 Go to the other side of the garage door and insert the end of the cable into the drum. Rotate the drum until the cable is tight. Slide the drum against the bearing and push the shaft to the right. The marks should line up. If they don't, figure out why and correct the problem. It could be a stuck cable, the garage floor may have shifted, or the vertical angle that helps support the bearing plate may have loosened and shifted. Many garage doors have been installed with a gap between a drum and a bearing plate. The cable drums should always be flush against the race of the bearings.
If your garage door is equipped with extension springs (usually seen on single car garages), the cable and pulley might be hanging down when the spring break's. Extension springs use a two pulley system on each side of the door to lift the garage door up and down. When the spring break's everything goes haywire, causing the cables to become twisted or even frayed when they catch on the metal edge of the track. There is a lot of force being released when a garage door spring breaks.
You may remember a time as a kid when you and your siblings would close the garage door and run underneath it as fast as possible to make it out before the door closed. Well, on any garage door installed after 1993, that’s no longer possible thanks to two tiny photo eyes on either side of the garage entrance. These photo eyes transmit an invisible beam between each other that detects if anything is in the garage door’s path when it closes. This safety measure is there to prevent automatic garage doors from closing on top of someone or something and causing serious injury or damage to property. https://www.youtube.com/watch?v=Z_eZc-kh40c&feature=share
Start your garage door spring replacement project by getting a rough measurement of your springs (length and diameter). Then measure the width and height of your door. Make sure the quote includes the trip charge, parts and labor. Then ask for a price based on 7x19 lift cables and double-life springs. Those items will give you more years of service and should only add $65 to the price.

Garage Door Repair Guy Centennial Co


SNAP... bang... boom. That is the sound of a garage door torsion spring breaking. It can be a very loud noise that sounds like a firecracker or gunshot. Springs are rated for a certain number of cycles and are the first thing that will break in your garage door assembly. Broken springs are the #1 source of customer calls for garage door repair companies. If you have a broken spring, you should NEVER try to open the door, as it can be very dangerous. This repair should be left to a professional or someone with the right tools and skills.
The history of the garage door could date back to 450 BC when chariots were stored in gatehouses, but in the U.S. it arose around the start of the 20th century. As early as 1902, American manufacturers—including Cornell Iron Works—published catalogs featuring a "float over door." Evidence of an upward-lifting garage door can be found in a catalog in 1906.[4] http://www.youtube.com/v/Z_eZc-kh40c&feature=kp
	10.5 If the spring comes loose from the cone at about 6 turns, you are probably winding the spring backward because the springs are on the wrong sides. Switch the springs. Otherwise, after winding the torsion springs, you will need to stretch the springs and secure the winding cone. First, mark the shaft 1/4" beyond the winding cone with tape or with a file. We stretch the springs because the shaft floats horizontally between the flexible end bearing plates as the garage door operates. Although this may be as little as 1/4" the binding of the coils as the door closes often keeps the door from closing completely, especially when the springs and bearings are dry and need lubrication.

Once the springs break, quite a bit of tension is put on the door cables, and they will often break next. When these cables break, they will snap and forcibly fly out like a broken rubber band. Think about how much it hurts to be snapped by a broken rubber band, and then multiply it by a hundred to account for the size and weight of the garage door cables. https://www.youtube.com/e/Z_eZc-kh40c
×