Replacing torsion springs is done with the door closed. You start by carefully unloading all of the springs (most standard-size doors have two; any broken spring will already be unloaded), using the winding bars. Then, you unbolt the springs from the central rod bracket, disconnect the cables from the pulleys, and loosen the pulleys and slide them off of the rod. Next, you swap out the springs, reinstall the pulleys and cables, and secure the inside ends of the springs to the central bracket. Finally, you wind up both springs (securing them with two setscrew bolts on the winding cones) and test the door for proper spring tension. Often, springs need an extra quarter-turn or two to get the door balance just right.

Anytime Garage Door Repair Centennial Co 80016


Grab a tape measure and press the hook between two spring coils and note the length of 20 coils. Then measure 40 coils. Convert the measurements to a decimal (4-1/2 in. to 4.5 in., or 4-1/8 to 4.125, for example). Divide the two measurements by 20 and 40 to obtain the spring's wire diameter. Here's an example: 4.50 divided by 20 = .225-in. wire diameter; 9.0 divided by 40 = .225-in. wire diameter. If the two results match, you've measured correctly.
Installing an overhead garage door requires a few tools and a friend to help. First, the lower door panel needs to be set up in the center of the doorway. The remaining panels and tracks are held in place with hinges, brackets, and screws. Set up an easy-to-install torsion spring system to ensure that your door lifts properly for many years to come.

Garage Door Repair Images Centennial Colorado 80016


If your photo eyes are clean and the door still isn’t closing, the next thing you’ll need to do is check the alignment of the eyes. The eyes should be pointing in exactly the same direction and at the same angle. If they’re off, they won’t register that the other one is there, and it’ll assume something is in its path, causing the door to stay in the open position. When checking the alignment, measure the height of each photo eye from the ground. Use a level to make sure they’re pointing directly across at each other at the same angle. A laser level will make this part a little easier, but if you don’t have one, a regular level will work as well. https://www.youtube.com/embed/Z_eZc-kh40c
Install the vertical roller tracks first by wrapping the curved lip around the rollers. The top of these tracks should be approximately 8 in. below the top of the top section. Wait to install the upper tracks until this step is complete. Check the level of the top section to make sure the tops of the vertical roller tracks are level with each other. The bottom of the roller tracks should be at least 1/8 in. off the concrete floor. After leveling and mounting these tracks, install the upper roller (horizontal) tracks.
If your garage door track is out of alignment, it can be a serious issue. The metal track your door runs on needs to be aligned properly in order for your door to move. If you see gaps between the rollers and rail, or bends in the rails themselves, you have a problem. The heavy weight of the door can compound these issues and make them worse until it becomes dangerous to operate your door.
Steel entry doors - when a garage is being fitted with new doors, it is also a good idea to consider a separate single 3x68 exterior door with half-glass and locksets too. These may require some carpentry, but they are a good way to allow for some flexibility in the choice of larger garage door, and can ensure that the homeowner will have more than a single way in or out of the structure. The average costs for such a feature range from $250 to $1000 each.
A standard double garage door is 7 ft. high by 16 ft. wide. Standard single doors are 7 ft. high by 8 or 9 ft. wide. Because the doors are so large, few home centers and only some garage door stores keep many doors in stock, so expect to order one instead of buying it off the shelf. Garage doors are available in wood, fiberglass and steel. Steel doors, like ours, are light, maintenance-free, affordable, readily available, and have an insulating value as high as R-19.
If your garage door goes up and down in a jerky motion, you might have one broken spring on a two spring system. Some garage door openers are strong enough to lift a door with only one good spring. The “herky jerky” motion is especially common with garage doors equipped with extension springs. It might be something as simple as lubricating your garage door pulleys, hinges, and rollers. When in doubt or if something doesn’t feel right about your door, call a service company to have it serviced.

Most homeowners never know they have a broken garage door spring until they try to leave their home. You go in the garage to open the door, push the wall button, and the door only goes up 6”. The reason for this is the garage door opener force or sensitivity has activated, causing the opener to stop pulling the door up. This is a safety feature built into most garage door openers. It is actually a good thing when the open force activates to prevent any damage to your garage door or opener.


The garage door opens and closes many times throughout the year, and something may blow inside. While it is usually something such as loose leaves or small amounts of dirt, the rails that the door travel along can collect this loose debris. Over time, the buildup of debris creates a blockage on the rails. Note where on the rails the door is stuck and clean that area. If children use the garage to leave the house, it's sometimes something as simple as a small, bouncing ball that happens to land in just the right -- or wrong -- spot. https://www.youtube.com/watch?v=Z_eZc-kh40c&hc_location=ufi
Test the door balance. A garage door should require only a few pounds of pressure to move it up and down. If springs wear out and lose their resiliency, a power garage door opener may need to work extra hard to lift the door. This can quickly wear out the motor on the opener. Replacing worn-out springs is usually a job for a professional technician. 

Garage doors make life easier, particularly when you’re arriving home in the middle of a rainstorm. It’s easy to take the convenience a garage door provides for granted -- until it stops working properly. The door loses its visual appeal instantly, stuck there half-open. This type of situation also raises security concerns as a simple trip to the store can become a headache. Simple fixes when a garage door gets stuck halfway may prevent it from happening again.
Electric Garage Door Openers – Service and repair of the electric garage door opener itself, including the lift mechanism that pulls the door up and guides it down. This is typically not part of the garage door itself and is serviced and repaired on its own interval. Typical service includes inspection, repair, adjustment, and lubrication if needed. Also, we typically inspect the mounting of the unit as well as its attachment to the door itself.
Product was received in two days and was as advertised. Installing these myself saved around $150 but it took around 2-3 hours. I would imagine everyone's experience is going to be different. These springs appear to be heavier duty than the ones they replaced. I couldn't use the same slots for tension as the old ones and it was trial and error in adjusting the length of my pull cable until the door closed as it should. I need to replace the springs on my other garage door and would think that will take less than an hour based on what I learned from the first install. https://www.youtube.com/v/Z_eZc-kh40c&feature=youtube_gdata
Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring.

Garage Door Repair Images Centennial Co


Inspect the area around your garage door to see if something is blocking the photo eye sensors. Then look at the tracks to see if there is any buildup on the inside. You’ll need to get a step ladder to look at the tracks on the top part of your garage, as it will be difficult to see from ground level. It may also not be a bad idea to proactively wipe down your garage door tracks periodically to prevent this type of buildup from occurring. Running a damp rag along each track should be enough to remove anything that’s lingering on the tracks.
Door styles - in addition to the styles just mentioned, it is important to also consider additional features such as windows across the top of the door to provide light inside of the garage, the use of steel or wood frames to give decorative doors added security and stability, and insulation which can reduce energy costs in the attached garage by an impressive 15 to 20%; and

Garage Door Repair Near Me Centennial 80016


6.13 Lower the second bar to the top of the garage door as you did the first bar. If your shaft is distorted inside the cone, you may need to tap the bar with a hammer as you unwind the spring. Maintain a firm grip on the bar; keep it firmly inserted completely into the cone; and be prepared at all times for the cone to slip, break, explode or snap loose from the shaft and jolt the bar down. https://www.youtube.com/watch?v=Z_eZc-kh40c&app=desktop
6.13 Lower the second bar to the top of the garage door as you did the first bar. If your shaft is distorted inside the cone, you may need to tap the bar with a hammer as you unwind the spring. Maintain a firm grip on the bar; keep it firmly inserted completely into the cone; and be prepared at all times for the cone to slip, break, explode or snap loose from the shaft and jolt the bar down.

Automatic Garage Door Repair Centennial Co 80015


10.7 Continue tapping until the cone moves out to the mark on the shaft. Continue holding the bar off the garage door and pulling back toward the center of the door. If the cone slips away from the mark, repeat this step. Keep an eye on the tape to make sure the bar doesn't slip out of the cone. If it does start to slip, rest the bar against the top of the garage door, insert a bar in the next hole and turn the cone up enough to make it possible for you to push the marked bar back into place.
Standard torsion springs (about $40 each) have a service life of 7,000 to 10,000 open/close cycles. However, you can buy double-life (25,000 cycles) replacement springs for about $65 per spring. If you have a two-spring setup and one spring breaks, the second spring will break soon. So replace them both at the same time. To get the right springs for your door, you'll have to provide the supplier some details. Here's how: http://www.youtube.com/watch?v=Z_eZc-kh40c&app=desktop
Both types of springs are loaded, or under tension, when the door is closed. This gives them stored energy to help lift the door as it's being opened. When the door is all the way up, the springs are relaxed, or relatively so—they still may be under some tension. The mechanical difference between extension and torsion springs is that extension springs are loaded by stretching, or elongating, while torsion springs are loaded by twisting, creating torque.
In order to prevent injury, garage doors automatically reverse if they come into contact with an obstacle. When the door closes halfway but then reverses for no apparent reason, this may be a sign that there is something preventing it from closing, something that you can't see. Check the tracks for stuff like dirt, rocks, bits of trash, or other debris. Give the tracks a wipe-down to dislodge anything that might be getting in the way.
9.8 Twist the garage door shaft to tighten the cable on the drum. While twisting, vise grip the shaft as shown to keep the cable tight on the drum. The top of the vise grip should be tight against the garage header. This will keep the cable snug on the first drum while you install the cable on the other drum and position it in place. It also keeps the shaft from turning and the cables peeling off when you wind the springs. That one grip can save many hours of walking back and forth and having to level and re-level the garage door after winding the torsion springs. http://www.youtube.com/watch?feature=youtube_gdata&v=Z_eZc-kh40c
Because garage doors are large, heavy, and mildly complicated, most people who buy them take advantage of these services. But, if you’re pretty adept at DIY tasks, you can save some money and enjoy the satisfaction of doing the job of installing a sectional garage door yourself. (Sectional garage doors travel up and down on rollers that ride along tracks at each side of the garage doorway.)

Garage door springs come in two styles: torsion (see above), which mounts on the header above the door, and extension (Photo 1), which floats above the upper roller track. In the past, extension springs were safer to install but didn’t have containment cables running through the center of the spring. Without cable, these springs become dangerous, heavy whips when they break. They also tend to be noisier than torsion springs, and we recommend you use them only if you don’t have the 12 in. of headroom above the door that a torsion spring requires. https://youtube.com/watch?v=Z_eZc-kh40c&app=desktop

Maybe the battery died or a spring broke, but you can't get into the garage to even see what the problem is. If the garage door is the only way in or out, or if you can't find the key to the door, you'll have to either find a way to break in or call a locksmith. As a preventative measure, it's smart to keep a spare key or install an emergency key release that would allow you to release the emergency disconnect to the operator so you can manually raise the door.


As commercial and residential garage door service professionals, we’ve pretty much dealt with every issue you can think of when it comes to garage door repair. Even still, there are sometimes issues that continue to surprise us, like the tiny insect nest growing on the photo eye sensor or the tennis ball that somehow managed to knock the door entirely off its track. Even though these issues are uncommon, it’s nothing that garage door service professionals like us can’t handle!
We want to hear from you and encourage a lively discussion among our users. Please help us keep our site clean and safe by following our posting guidelines, and avoid disclosing personal or sensitive information such as bank account or phone numbers. Any comments posted under NerdWallet's official account are not reviewed or endorsed by representatives of financial institutions affiliated with the reviewed products, unless explicitly stated otherwise.
Poor lubrication is a very common and easy to fix explanation for why you might find your garage door stuck. You should properly lubricate your garage door's track, the opener chain and the springs every few months as part of regular preventative maintenance. Be sure to use Clopay's Garage Door ProLube or sillicone based lubricants. Do not use WD-40.

Garage Door Repair In My Area Centennial Colorado 80016


Noisy garage doors cause all kinds of problems, especially for anyone who has to sleep above or next to the garage. Fortunately, most noisy garage doors can be fixed with a combination of routine maintenance and the replacement of a few parts. If the basic maintenance tips described above don't quiet a noisy garage door, it's possible that the door's hinges need to be replaced.
Torsion springs are located above the opening of your door with springs that slide onto a bar. Extension spring systems can be found alongside the opening of the door. It's important to know whether or not a garage door company provides service for your needs. Precision's professionally trained technicians are fully equipped to work on torsion and extension spring systems. http://m.youtube.com/e/Z_eZc-kh40c
×