Installing an overhead garage door requires a few tools and a friend to help. First, the lower door panel needs to be set up in the center of the doorway. The remaining panels and tracks are held in place with hinges, brackets, and screws. Set up an easy-to-install torsion spring system to ensure that your door lifts properly for many years to come.

Garage Door Repair Images Centennial Colorado 80016


While it would be wonderful if door springs lasted forever, the reality is that the simple act of opening and shutting the door multiple times every day isn’t easy. It’s hard on the springs, even though they’re built to do it. Most springs will last for a while, but they won’t last forever. The regular wear and tear of endlessly opening and shutting the door breaks them down and eventually, they’ll need to be replaced.
Extension springs are long, lighter-weight springs that run perpendicular to the door and are mounted above the horizontal portions of the door tracks. These springs are tensioned by stretching out, using cables and pulleys, as with the torsion system. Because extension springs are merely suspended between two brackets (they are not mounted to a rod, like torsion springs), they must have a safety cable running through each spring. This helps contain the spring in the event of a breakage. Without the safety cable, a spring breaking under tension is a very serious safety hazard. If you have old springs that don't have safety cables, you should install them even if you aren't replacing the springs.

If the track is misaligned, but the door still moves, there are a few things you can do to attempt to remedy the issue on your own. You’ll know that it’s misaligned if you hear a rubbing noise when the garage door reaches a certain spot on the tracks each time it opens and closes. Sometimes the door may even slow down slightly when it hits this spot.
We look out for the safety of our customers and their families. That’s why we do not sell garage door torsion springs separately to consumers, and it’s also why we recommend putting your broken garage door in the hands of our experienced technicians. At Garage Door Medics, we are licensed, bonded, and insured. We have completed thousands of garage door installations and spring repairs, and we make sure they are done safely and with the right springs for your garage door system.
Lewis did a great job and not only met my expectations but blew them away. His attention to detail was impressive. He reolaced the springs on my two car garage door and he went out of his way to adjust the tension on my second single car garage door to make it open better. He also recommended replacement of the rollers on my main garage door as they were getting pretty worn out and making some noise. He was very friendly and personable. Was willing to explain what he was doing so we could learn something too. I would recommend Lewis Nagy if you are in his area here in Apollo Beach/Riverview. Thanks again!
The winding and unwinding is done at a metal fitting, called a winding cone, attached to the outside end of the spring. You stick a winding bar into one of the four holes in the cone and use the bar as a lever to turn the cone. Once you've completed a quarter turn, insert the other bar into a different hole in the cone and let the bar lever against the closed garage door to hold the spring tension. This allows you to move the original bar to repeat the process, alternating the bars with each quarter-turn. It takes about 30 quarter-turns to fully tension a standard torsion spring.

Affordable Garage Door Repair Centennial Colorado 80016


You can reschedule or cancel your service at any time. To reschedule, simply go to Your Orders, find your service order and click on the ‘Contact Provider’ button on Your Orders page. To cancel, click on the 'Cancel Order' button on Your Orders page. Payment goes to the pro from your secure Amazon account. Because you aren't charged until the actual work is completed, cancelling a job doesn't require a refund.

Unlike torsion springs, replacing extension springs has long been given the "green light" for DIYers, primarily because you can complete the job without having to deal with spring tension. The general process is simple and safe: open the door to relieve the spring tension (and secure it open with C-clamps in the tracks); disconnect the spring from the track bracket and the spring pulley, and disconnect the safety cable from one end; install the new spring, reinstall the pulley, and reconnect the safety cable, and you're done.
If your photo eyes are clean and the door still isn’t closing, the next thing you’ll need to do is check the alignment of the eyes. The eyes should be pointing in exactly the same direction and at the same angle. If they’re off, they won’t register that the other one is there, and it’ll assume something is in its path, causing the door to stay in the open position. When checking the alignment, measure the height of each photo eye from the ground. Use a level to make sure they’re pointing directly across at each other at the same angle. A laser level will make this part a little easier, but if you don’t have one, a regular level will work as well. https://www.youtube.com/embed/Z_eZc-kh40c

If you’ve tested and tried to remedy these other problems and you’re still having issues, you may need to reprogram your transmitter. All transmitters have a learn button somewhere on the remote, so first you’ll need to locate that on your transmitter. Press and hold the learn button for a few seconds until the indicator light starts blinking. While the light is blinking, press your remote button again to reprogram that remote. http://www.youtube.com/watch?v=Z_eZc-kh40c

Measure area labeled headroom (5), which is the distance between the top of the door opening (jamb header) and the ceiling (or floor joist). 10" is required for the standard extension spring or EZ-SET® Extension Spring System while 12" is required for a standard torsion spring and EZ-SET® Torsion Spring System. If you have restricted headroom, special hardware is available. Additional headroom is required for installation of an automatic garage door opener. NOTE: If garage door height extends above the opening, the headroom measurement should be adjusted proportionately.


Started in 2004, Aladdin Garage Doors has become known nationwide as the trusted source for garage doors, repairs, and fast, efficient service. With a mission focused on delivering outstanding customer care, we’re proud to offer garage doors that lead the industry in quality, value, and lifetime protection for homes and businesses. Whatever your garage door needs may be, you can count on Aladdin Garage Doors to offer: https://www.youtube.com/attribution_link?a=Z_eZc-kh40c&u=%2Fwatch%3Fv%3DXXXXXX%26feature%3Dshare
R-value describes the power of the insulation in your door. The higher the r-value, the stronger the insulation. Those doors will have better energy efficiency than doors that have a low r-value. Basic doors have an r-value of 0.0 with no insulation. The first step up gives you 1-3/8” insulation at a 6.5 rating. Next, a 1-3/8” thickness with Intellicore has a 12.9 r-value. The best option on the market is the 18.4 r-value, which has 2” Intellicore insulation.
Product was received in two days and was as advertised. Installing these myself saved around $150 but it took around 2-3 hours. I would imagine everyone's experience is going to be different. These springs appear to be heavier duty than the ones they replaced. I couldn't use the same slots for tension as the old ones and it was trial and error in adjusting the length of my pull cable until the door closed as it should. I need to replace the springs on my other garage door and would think that will take less than an hour based on what I learned from the first install.
6.4 Test the fit of the bar in the cone before loosening a set screw. Insert one end of your winding bar into one of the holes of the winding cone. Pull down on the bar slightly to make sure the set screws are tight. Position your ruler between the bar and the garage door. Move the bottom of the bar from side to side and measure the play. It should be less than an inch and a half. If it is over 2" either get someone else to change your springs or have someone make some bars that will properly fit the cones.

Garage Door Repair Free Quote Centennial Colorado


Replacement spring procedure took me exactly 1 hours including preparation and clean-up for double aluminum garage door. Watch the DIY video on Youtube, save $$, be careful with winding the torsion springs. Rule of thumb: 7' height door garage= 7' x 4 (each 1/4 turn) + 1 = 29 turns (1/4 turn), 8' height door garage = 8' x 4 + 1 = 33 turns (1/4 turn), and so on....
Install new or use this right-wound torsion spring Install new or use this right-wound torsion spring to replace broken sectional garage door torsion springs. All DURA-LIFT springs meet the DASMA standard rating of 10 000 plus door open and close cycles. Both the winding and stationary cones are professionally installed for safe operation. Winding rod is included with ...  More + Product Details Close
Replacing torsion springs is done with the door closed. You start by carefully unloading all of the springs (most standard-size doors have two; any broken spring will already be unloaded), using the winding bars. Then, you unbolt the springs from the central rod bracket, disconnect the cables from the pulleys, and loosen the pulleys and slide them off of the rod. Next, you swap out the springs, reinstall the pulleys and cables, and secure the inside ends of the springs to the central bracket. Finally, you wind up both springs (securing them with two setscrew bolts on the winding cones) and test the door for proper spring tension. Often, springs need an extra quarter-turn or two to get the door balance just right. 

Anytime Garage Door Repair Centennial Co 80016


While it would be wonderful if door springs lasted forever, the reality is that the simple act of opening and shutting the door multiple times every day isn’t easy. It’s hard on the springs, even though they’re built to do it. Most springs will last for a while, but they won’t last forever. The regular wear and tear of endlessly opening and shutting the door breaks them down and eventually, they’ll need to be replaced.
Your decision on whether to try and replace a broken spring may depend on what type of springs you have. Garage door springs come in two main types: extension and torsion. Identifying which type you have is easy. If your door system has a long, skinny spring running parallel to each horizontal door track, then you have extension springs. If your door has one or more beefy springs on a metal rod parallel to, and directly above, the door opening, then you have torsion springs. Both of these springs are found on standard sectional garage doors. If you happen to have an old one-piece, swing-up door with vertical springs at both sides, you also have a variety of extension springs, sometimes called side springs.
Although garage door springs can break during any season and at any time, they most commonly break during the winter. This has to do with the temperature change. When the temperature sinks below a specific threshold, the metal will contract. This means it’s extremely possible for your door springs to shrink slightly during the winter months. This is hard on the springs and makes them more likely to break.
Looking to repair your garage door opener? Common problems could range from issues with the remote or wall switch that control the garage door opener to more serious issues like a grinding noise coming from the opener itself. If you need help with repairing your garage opener, schedule a repair appointment today! We repair all major brands and have same-day availability in most markets, so we can get your garage door opener repaired and running smoothly. To learn more about the cost of repairing garage doors, visit our garage door and opener installation and repair cost guide.
Scott was exceptionally polite, professional and knowledgeable. He thoroughly checked my garage door opener, but also inspected the garage door itself and pointed out rust and deterioration that has occurred. Scott then gave me a quote on a new garage door, explaining the installation procedure and quality elements of the new door including the warranty. I was very pleased with the entire service appointment, and my husband and I are seriously considering the new garage door, but only if Scott is the installer! Thanks, Scott!
Locating a contractor - there are many professional overhead garage door companies. It is always advisable to contact at least three different agencies and request a bid or quote for the work. Be sure that each quote includes the costs for a few different types of doors, any installation fees, and the cost of wiring the electronic openers. Standard prices range from: https://www.youtube.com/watch?v=Z_eZc-kh40c&app=mobile

As a first time homeowner, Home advisors is an invaluable tool! There is a steep learning curve that comes with buying a house!!!! Being able to have access to unbiased information is great! It really helps to have a basic idea of what costs are, and all the different things that go into each project. who knew that there was so much to consider when looking to replace garage doors!!!!
Everyone wants to save money. Unfortunately, there are some areas you just can’t skimp on. This includes garage door springs. As much as it might be tempting to by smaller or cheaper springs, or maybe to buy one spring where two are needed, these attempts to save money will only end up costing more money in the end. When you buy the proper springs, they’ll last for years. When you cut corners to save money, the springs will wear out faster, meaning they’ll need to be replaced much sooner.

Homeowners have long been warned that torsion springs are extremely dangerous to work with and that replacing them must be left to a professional. But these claims are somewhat exaggerated. If you understand how they work, and you pay attention to what you're doing, you can replace them safely and surprisingly easily. Granted, they're a little spooky to work with at first (partly due to their reputation), but this is a good thing—you really don't want to forget that they're under tension. Thinking about every step — before you take it — is the key to staying safe.
We look out for the safety of our customers and their families. That’s why we do not sell garage door torsion springs separately to consumers, and it’s also why we recommend putting your broken garage door in the hands of our experienced technicians. At Garage Door Medics, we are licensed, bonded, and insured. We have completed thousands of garage door installations and spring repairs, and we make sure they are done safely and with the right springs for your garage door system.

A1 Garage Door Repair Centennial Colorado 80016


10The type of garage door shown provides the necessary lift assistance with a “torque tube.” If you intend to use an opener, wait to install the tube. Otherwise, install the torque tube according to the manufacturer’s directions. Roll up the door about 4 feet to check for the alignment of the tracks, and make any adjustments. Then tighten all fasteners.

Garage Door Repair Free Estimate Centennial Colorado


Wood - Wood garage doors are sturdy and quite beautiful. However, if you live in a humid climate, your doors will be prone to rotting and splitting. If your wood is painted, you must also factor in the costs of painting as part of your regular maintenance routine. The cost of repairing the wood varies depending on the type. However, average cost to repair a wood panel is $190 to $215.
The low rating on the CS is due to the fact that inwas out of town and my wife called because the garage door wouldn't open. We had repairs to the only other exit, and the CS said because it could be opened manually, it was no emergency. She was stuck in the house for over Sixteen hours. No emergency crew came out. Steve, a tech who came out the first time, fixed the door. It is not his fault CS took their sweet time to help a 45 year customer. I commend Steve. I do NOT have anything good to say about CS.
Grab a tape measure and press the hook between two spring coils and note the length of 20 coils. Then measure 40 coils. Convert the measurements to a decimal (4-1/2 in. to 4.5 in., or 4-1/8 to 4.125, for example). Divide the two measurements by 20 and 40 to obtain the spring's wire diameter. Here's an example: 4.50 divided by 20 = .225-in. wire diameter; 9.0 divided by 40 = .225-in. wire diameter. If the two results match, you've measured correctly.

Affordable Garage Door Repair Centennial Colorado 80015


The problem is that one of the garage doors "catches" (i.e. stops) while going up at about 2 feet off the ground ~90% of the time. When the button is pressed again, it goes all the way down. This cycle can be repeated ad nauseum, or I can give the door a gentle tug upward just before the "Sticking" point, and this will give the door enough "impetus" to make it all the way up.
Torsion-spring doors have a drum-like pulley at each end of the metal rod that runs through the springs. Each pulley has a cable attached to the bottom of the door. The springs and pulleys are fixed to the rod so they all rotate together. When the door closes, the rod turns and winds up the springs, creating tension. When the door opens, the springs release the tension and turn the rod in the opposite direction. http://youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c
Torsion springs do not last forever, regardless of what some companies claim. “Lifetime” springs do not exist – all springs have a lifespan. Most builders typically install the lowest costing door available and with that generally comes lower cycle springs. A torsion spring’s life is determined by the number of cycles the spring is rated to last. Whenever the door goes up and down is what is referred to as a “cycle.” The springs that builders install can last as little as 7,500 cycles which means the average homeowner could get 3-5 years of life. http://y2u.be/Z_eZc-kh40c
×