There’s never a convenient time for your garage door springs to break. When this crucial component gives out, you need a repair job or replacement as soon as possible. That’s why Marvin’s Garage Doors is available 24/7 for emergency service. When that emergency arises, or you’re stuck in your garage and unable to get out to get to work, simply give us a call on our emergency line at 336-813-2601.
When one or both springs break, gravity takes over and you feel the full weight of the door when lifting or lowering it.  It may be possible to pull the door up by hand, although doing so will likely be very difficult. In most cases, two or more people are needed to raise the door high enough for you to drive your car out of the garage. While single garage doors can typically be lifted, double doors are nearly impossible to manipulate due to their excessive weight.
Sears garage repair technicians are fast, with same-day, emergency repairs available in most areas. We can replace garage door broken springs, rollers, cables, hinges, sensors and weather seals. We can also adjust garage door tracks and springs to make sure your door operates smoothly. Having problems with your garage door opener? We can repair or replace that too. Check out our line of Craftsman Garage Door Openers. Craftsman is America’s #1 brand of garage door openers! 1
1. Garage door springs do almost all of the work of lifting your door regardless of the door being manually or automatically operated. The spring makes it possible for anyone to lift a product that might weigh one hundred pounds on the low end and many hundreds of pounds on the high end. Not only can anyone lift it – most can do it with one hand! In other words, the garage door spring does a lot of work.
9.8 Twist the garage door shaft to tighten the cable on the drum. While twisting, vise grip the shaft as shown to keep the cable tight on the drum. The top of the vise grip should be tight against the garage header. This will keep the cable snug on the first drum while you install the cable on the other drum and position it in place. It also keeps the shaft from turning and the cables peeling off when you wind the springs. That one grip can save many hours of walking back and forth and having to level and re-level the garage door after winding the torsion springs.

Ace Garage Door Repair Centennial Co 80016


Automatic doors require not only the installation of a heavy door, but the motor and cables as well. Automatic doors are much more common now because of their convenience, but in a case such as the heavy wood door, they are a necessity. A strong motor is required to pull up a heavy door. However, automatic doors are not without their faults -- they quickly become a manual door when the power goes out.

Garage doors are the largest moving object inside your home. If you have a problematic garage door, it compromises the safety of your family and home. Ankmar Denver is a professional company you can count on. We provide you with quality service at a reasonable price. We offer FREE estimates on replacement garage doors and are spring replacement specialists. 24 hours a day 7 days a week we are your number one garage door repair service.

Garage Door Repair Average Cost Centennial Co 80016


A garage door spring replacement should cost between $175 and $225 for a single tension spring and between $250 and $300 for two tension springs. Most garage door companies carry a wide enough variety of spring sizes to cover most residential doors. As long as the proper amount of turns are put on the spring, there are more than one correct springs to use for any one door.
I have 2 full house humidifiers that have stopped functioning right. There are new filters, fan runs, tanks are full of water but they are not empting into the base. They have worked for part of the winter and now nothing seems to help...I loosened the caps thinking I had them too tight..... nothing seems to work .I have had humidifiers for 20 years and this is the first time this has happened to me. The humidifiers are only 2 years old. Any suggestions??
We have had many concerns with our garage opener unit both safety issue and sleepless nights. At this time we are pleased that so far the unit is operating as it should.Hopefully we hope the issue of the unit opening by it self at early morning hours is solved. And if this is so, we want to Thank all involve in bring a satisfactory solution to this nightmare. https://m.youtube.com/watch?v=Z_eZc-kh40c&feature=youtube_gdata
Garage door springs offset the weight of a garage door and allow the door to be opened and closed easily, either by hand or by an automatic garage door opener. The high-tension steel in the springs has a limited lifespan, and over time, the springs lose their effectiveness. Garage door springs come in levels of quality—they may be described as "10,000-use" or "20,000-use" springs, for example. This may sound like a very large number, but when you consider that a garage door might be opened four or five times a day, every day, every year, it becomes clear that there is a limited lifespan for these critical garage door parts.
"Our garage door wouldn’t shut on sunny days and the tech came out. He explained my options (swap the “seeing” sensor with the other, or replace them). He tried swapping and it was still an issue so he replaced them. In addition, he adjusted the spring because the company that installed it last year did not adjust it properly. He was here for about two hours and charged us for only the sensor replacement. Will definitely be using this company again! Highly recommend them. "

In order to prevent injury, garage doors automatically reverse if they come into contact with an obstacle. When the door closes halfway but then reverses for no apparent reason, this may be a sign that there is something preventing it from closing, something that you can't see. Check the tracks for stuff like dirt, rocks, bits of trash, or other debris. Give the tracks a wipe-down to dislodge anything that might be getting in the way.
10.4 Raise the second bar 90 degrees and insert the first bar. This is "three." Continue winding. If the spring shortens in length, unwind the spring and switch sides - the springs are on backward. Otherwise, continue winding until you reach a count of "30." This is 7 1/2 turns, which is normal for most 7' doors. Longer life springs are wound the same number of turns. Newer steel doors with only one strut on top often need only 7 1/4 turns. On 8' doors count to 34. Each time you insert a bar into the winding cone, listen for the click to let you know the bar is in all the way. Not inserting the bar all the way could cause the cone to explode.

Garage Door Repair Near Me Centennial Colorado 80016


R-value describes the power of the insulation in your door. The higher the r-value, the stronger the insulation. Those doors will have better energy efficiency than doors that have a low r-value. Basic doors have an r-value of 0.0 with no insulation. The first step up gives you 1-3/8” insulation at a 6.5 rating. Next, a 1-3/8” thickness with Intellicore has a 12.9 r-value. The best option on the market is the 18.4 r-value, which has 2” Intellicore insulation.
Another scenario is the garage door goes up very slowly when using the automatic opener. Some garage door openers have DC motors that start off slow when opening and then kick into a higher speed. If you have a broken spring, the opener might stay in the slower speed due to the heavy weight of the garage door. If this happens to you, close the garage door and pull the emergency release rope. Next, try to lift the door. If it is really heavy, then you most likely have a broken garage door spring. 

6.13 Lower the second bar to the top of the garage door as you did the first bar. If your shaft is distorted inside the cone, you may need to tap the bar with a hammer as you unwind the spring. Maintain a firm grip on the bar; keep it firmly inserted completely into the cone; and be prepared at all times for the cone to slip, break, explode or snap loose from the shaft and jolt the bar down. https://www.youtube.com/watch?v=Z_eZc-kh40c&app=desktop
One of the best ways to care for your springs is to check them over for wear. You can certainly look at them for damage, but sometimes the damage isn’t something that’s visible. In these cases, try lifting the garage door up from the ground. About halfway up, let go. If the door stays, the springs are still working perfectly. If the door sags or drops at all, this could be a sign that your springs are beginning to weaken and will need replacing soon.

Maybe the battery died or a spring broke, but you can't get into the garage to even see what the problem is. If the garage door is the only way in or out, or if you can't find the key to the door, you'll have to either find a way to break in or call a locksmith. As a preventative measure, it's smart to keep a spare key or install an emergency key release that would allow you to release the emergency disconnect to the operator so you can manually raise the door. 

Garage Door Repair Free Estimate Near Me Centennial Colorado 80016


We couldn't have been happier with the technician. He was prompt, efficient, didn't complain about moving items to do the installation, cleaned up after himself, was polite and thorough. He seemed very sure of exactly what to do next. As a favor, he took a couple of minutes to remove a light globe to replace a bulb since he had the ladder in the garage because we can't get to it. We were very impressed with him. We would definitely request him again.
Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.

Garage Door Repair Bracket Centennial Colorado 80016


Inspect the area around your garage door to see if something is blocking the photo eye sensors. Then look at the tracks to see if there is any buildup on the inside. You’ll need to get a step ladder to look at the tracks on the top part of your garage, as it will be difficult to see from ground level. It may also not be a bad idea to proactively wipe down your garage door tracks periodically to prevent this type of buildup from occurring. Running a damp rag along each track should be enough to remove anything that’s lingering on the tracks.
These instructions were first posted in 2005, and they were updated in August of 2008. I have been frank about the hazards of garage door repairs and about my own accidents incurred while replacing torsion springs. For what it's worth, you might be surprised to know that I, too, have benefitted from producing these instructions. I have not had any garage door accidents since we first published these on the web in 2005. And, in as much as I have helped keep other DIY-ers out of the emergency room, I consider myself somewhat of a medical practitioner.

Garage Door Repair In My Area Centennial Co 80015


Good response time and service; Question - I googled to find the Sears Garage Door repair phone number. During the conversation, I was unsure if this was "Sears" or a "contractor service" or other service. I had to ask if this repair person was coming from "Sears" or an independent repair. I was concerned until the service man arrived in a sears truck wearing Sears apparel. You might want the process to be more clearly identified as Sears.
Home Depot local Service Providers are background checked, insured, licensed and/or registered. License or registration numbers held by or on behalf of Home Depot U.S.A., Inc. are available at homedepot.com/licensenumbers or at the Special Services Desk in The Home Depot store. State specific licensing information includes: AL 51289, 1924; AK 25084; AZ ROC252435, ROC092581; AR 228160518; CA 602331; CT HIC.533772; DC 420214000109, 410517000372; FL CRC046858, CGC1514813; GA RBCO005730, GCCO005540; HI CT-22120; ID RCE-19683; IA C091302; LA 43960, 557308, 883162; MD 85434, 42144; MA 112785, CS-107774; MI 2101089942, 2102119069; MN BC147263; MS 22222-MC; MT 37730; NE 26085; NV 38686; NJ 13VH09277500; NM 86302; NC 31521; ND 29073; OR 95843; The Home Depot U.S.A., Inc. is a Registered General Contractor in Rhode Island and its Registration Number is 9480; SC GLG110120; TN 47781; UT 286936-5501; VA 2705-068841; WA HOMED088RH; WV WV036104; WI 1046796.
Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring.

Started in 2004, Aladdin Garage Doors has become known nationwide as the trusted source for garage doors, repairs, and fast, efficient service. With a mission focused on delivering outstanding customer care, we’re proud to offer garage doors that lead the industry in quality, value, and lifetime protection for homes and businesses. Whatever your garage door needs may be, you can count on Aladdin Garage Doors to offer:


Whenever a spring breaks, the door will not go up. Attempting to lift a door with a broken spring can be extremely dangerous. Attempting to replace the springs yourself is even more dangerous. You should never attempt to fix a broken spring yourself – only experienced, trained professionals should ever touch torsion springs. Also replacing a spring requires expertise to know exactly which spring to replace it with. The correct springs are determined based off the weight of the door. There are hundreds of combinations of springs but only one is correct for your door. It is important to have the correct springs to prevent an array of problems in the future. With the wrong springs, your opener will break much quicker and your door is more likely to come off tracks. It is alarming how many installers use the wrong size springs. Knowing which springs to use can only be determined by experience.

Jerrod the technician had answers to all my questions. He was very knowledgeable and very patiently explained what was going on with my garage door and the opener. I would definitely recommend A1 garage door service to friends and family. I was given options to either repair the door or replace it. I will get the door replaced when it gets non-functional from A1 garage door service.

Garage Door Repair Companies Centennial Colorado 80015


Replacement spring procedure took me exactly 1 hours including preparation and clean-up for double aluminum garage door. Watch the DIY video on Youtube, save $$, be careful with winding the torsion springs. Rule of thumb: 7' height door garage= 7' x 4 (each 1/4 turn) + 1 = 29 turns (1/4 turn), 8' height door garage = 8' x 4 + 1 = 33 turns (1/4 turn), and so on....

Quite a few garage doors come with manual locks, especially older models, for added security for your house. These typically look like a knob or handle in the middle of your door with two bars running horizontally from each side. There may be a small button on the top or side of the handle that you can press to slide the bars across the doors, thus locking the garage door from the inside. It can be somewhat easy to accidentally hit that button, especially if you’re getting large objects out of the trunk of your car near the door.


Just like car tires are rated by miles, garage door springs are rated by an estimated number of cycles (1 cycle = your garage door going up AND down 1 time). The springs used by our competition range anywhere from 5,000-10,000 cycles, whereas we use a high-grade steel spring rated for 25,000-50,000 cycles! This is why we can offer a Lifetime Guarantee on our springs when we overhaul your door for as long as you live in your home!


Many jobs around the house are fairly easy fixes. It’s relatively easy to clean out your fireplace, clean the leaves from the gutters or repaint a wall. It’s a different thing to replace your garage door spring. It’s careful work that is almost impossible to do correctly the first time. Garage door professionals spend a great deal of time learning how to do it properly, and even the most detailed instructions won’t make you an expert in the span of a few hours. It can be almost infuriatingly annoying at times and is simply better left to professionals.
A typical version of an overhead garage door used in the past would have been built as a one-piece panel.[1] The panel was mounted on each side with unequal parallelogram style hinge lifting mechanism. Newer versions of overhead garage doors are now generally built from several panels hinged together that roll along a system of tracks guided by rollers.[1] The weight of the door may be 400 lb (181.4 kg) or more, but is balanced by either a torsion spring system or a pair of extension springs.[2] A remote controlled motorized mechanism for opening garage doors adds convenience, safety, and security.[3]

On our EZ-Set Torsion Springs page you will find several options for replacing these springs. We also have step by step instructions for EZ-Set Torsion Spring Replacement. In addition, one of our customers has provided excellent EZ-Set Torsion System instructions for removing the spring without wrecking the winding unit that secures the stationary cone. Instead of a spanner tool, you may prefer to use a pipe wrench or large channel locks to hook the end of the spring and remove it from the cones in the last step. http://www.youtube.com/v/Z_eZc-kh40c?version=3
×