In order to prevent injury, garage doors automatically reverse if they come into contact with an obstacle. When the door closes halfway but then reverses for no apparent reason, this may be a sign that there is something preventing it from closing, something that you can't see. Check the tracks for stuff like dirt, rocks, bits of trash, or other debris. Give the tracks a wipe-down to dislodge anything that might be getting in the way. https://youtube.com/watch?v=Z_eZc-kh40c
There are many steps to replacing torsion springs, but overall it's a simple, straightforward process. If you're inclined to attempt it, find a good online video tutorial (preferably done by a garage door pro) that walks you through the entire process, including how to buy the right size of springs. You can also buy new springs and any related parts online, along with the most important items that you need: the two solid-metal winding rods that you use to wind and unwind the torsion springs.
If you have a garage door opener and you suspect a spring has broken, do not disconnect the opener from the door (by pulling the red emergency release handle) while the door is open. If you do, the door can come crashing down under its nearly full weight, with nothing to stop it. This is an extremely dangerous situation. It is never safe to leave the door open when a spring has broken because someone might try to close the door without realizing how heavy it is. Or, they might pull the emergency release handle on the opener.
Install the stiffening strut on top of the top section of steel doors with the section lying flat. Then install the opener bracket that replaces the center bracket between the top two sections. While you’re working on the sections, protect them from scratches by putting carpet scraps on top of your sawhorses. Now, slide the rollers into the roller brackets.
No matter what kind of door you are installing, be very careful. The instructions that follow are merely guidelines. You should read your garage door manufacturer's instructions and owner's manual very carefully before attempting either type of installation. And if you're a do-it-yourself greenhorn, skip this project and hire an experienced professional. It may be more expensive, but garage door installation is on the higher scale of DIY difficulty.
9.6 Bending the cable will help you avoid problems with the tip at the end of the cable catching on the end bearing plate and causing the cable to come off and the garage door to jam, cock, or fall. Check to make sure the cable is straight in the slot and not sticking out the side. Also the edge of the cable stop should not be pointing to the side as displayed. The cable tip should fit completely inside the drum, with the rounded part facing out so the tip can't scrape the end bearing plate.
7.2 If the spring bracket is slotted, vise grip the bracket to secure the shaft in the bracket. This will keep the shaft from possibly falling out and causing injury or damaging the garage door or shaft. You can also secure the shaft with a cable tie. Remove the bushing from the cone and leave it on the shaft next to the center spring bracket. Often the bushing gets stuck in the cone and customers will call us about getting a new bushing until they discover it is still in the cone of the spring replaced earlier. http://www.youtube.com/v/Z_eZc-kh40c&feature=youtu.be
Scott was exceptionally polite, professional and knowledgeable. He thoroughly checked my garage door opener, but also inspected the garage door itself and pointed out rust and deterioration that has occurred. Scott then gave me a quote on a new garage door, explaining the installation procedure and quality elements of the new door including the warranty. I was very pleased with the entire service appointment, and my husband and I are seriously considering the new garage door, but only if Scott is the installer! Thanks, Scott!
The first thing to look for if your door is stuck is to check the sensors. Most automatic garage doors come with two sensors located on either side toward the bottom of the garage that will stop the door from closing in the event the event that a child or pet is in the way of the door. If your door gets stuck, the first thing to do is look at both sensors and make sure nothing is in the way.
The garage we take for granted very likely stores thousands of dollars worth of tools and household belongings, not to mention your automobiles. Yet this space is typically rather easy for intruders to penetrate. Garage security can be greatly improved by installing a modern garage door opener that features rotating digital codes, which can foil even the most tech-savvy prowlers.
10.4 Raise the second bar 90 degrees and insert the first bar. This is "three." Continue winding. If the spring shortens in length, unwind the spring and switch sides - the springs are on backward. Otherwise, continue winding until you reach a count of "30." This is 7 1/2 turns, which is normal for most 7' doors. Longer life springs are wound the same number of turns. Newer steel doors with only one strut on top often need only 7 1/4 turns. On 8' doors count to 34. Each time you insert a bar into the winding cone, listen for the click to let you know the bar is in all the way. Not inserting the bar all the way could cause the cone to explode.

Garage Door Repair Near Me Centennial Colorado 80016


Professionals can replace garage door springs in an hour or two. When you hire a pro, make sure to ask about the quality of the springs they will install. They may well offer several grades of springs to choose from, at a range of costs. Top of the line springs may be guaranteed for life, while economy springs can be expected to last perhaps five years under normal use.
Instead, try other methods that might break the frozen connection between the door and the floor. For example, you can use a heat gun or hair dryer to melt the ice and free the door. Standard de-icing products can also work. And if you are careful not to damage the door or the seal on the bottom of the door, you can use a flat shovel or similar tool to chip away at the ice.

Garage Door Repair Guy Centennial Colorado 80016


Unlike torsion springs, replacing extension springs has long been given the "green light" for DIYers, primarily because you can complete the job without having to deal with spring tension. The general process is simple and safe: open the door to relieve the spring tension (and secure it open with C-clamps in the tracks); disconnect the spring from the track bracket and the spring pulley, and disconnect the safety cable from one end; install the new spring, reinstall the pulley, and reconnect the safety cable, and you're done. https://www.youtube.com/v/Z_eZc-kh40c&feature=kp


The tricky parts of the job involve you carrying the tension of the spring. Replacing a spring requires that you first unwind the spring to relieve the tension, then wind it back up and secure it while it's under tension. Winding bars are used for all winding and unwinding actions—don't try to save a few bucks by substituting long screwdrivers or pieces of rebar for the real winding bars. Substitute tools are much more likely to slip, or they may bend or break under the load of the spring. https://youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c
If your garage door is equipped with only one torsion spring, it will be much harder to get your door open. You will need to get 2-3 people to help lift the door up because the full weight can be anywhere from 150 to 300 pounds. We don’t recommend lifting the door when the spring break's due to the danger of it falling on someone. If you absolutely must get your garage door open, raw strength is what you need. When you get the door in the up position, use vise-grips or a c-clamp on the track below the bottom roller to hold the door in the up position.

Affordable Garage Door Repair Centennial Co 80015


Whether you're planning on moving in the future or you're fixing up your forever home, replacing a garage door can provide an excellent return on investment and boost your home's resale value. According to Remodeling magazine's 2016 Cost vs. Value report, garage door upgrades provide a nationwide average return on investment of over 90%, making it one of the top five home improvement projects. To learn more about the cost of installing garage doors, visit our garage door and opener installation and repair cost guide.
I went on Garage Door Nation website to look at the conversion chart from 1 to 2 torsion springs. For my 1 spring, size 2"/0.250ID/30.5" length, they recommended 2 of 2"/0.207ID/24" length. I got this kit from Amazon for $64 with $11 overnight shipping even though I could get free shipping through Prime over the weekend, but I couldn't wait for 3 more painful days. Installed it followed YouTube video. Worked better than my old one, a lot quieter. Check the video if you want to install one yourself. Professional installation costs hundreds of $$$:

Garage Door Repair Centennial 80015


Your dream car is parked in out of the elements, but it's not secure because the garage door won't lock. Most garage doors have two horizontal bars that move out from the center of the door into slots along the side of the door in the door track, effectively locking the door in place. Over time, these bars can shift slightly out of position so that they are no longer correctly aligned with the locking slots. To realign the bars, unscrew the guide brackets on the edges of the door so that they are loose enough to move, and then reposition them so that they smoothly guide the locking bars into the locking slots. Lubricate the lock mechanism with machine oil and you're done.
First, check to see if the transmitter on the wall inside your garage still opens your garage door when pressed. If it does, then the transmitter in your car likely just needs a simple battery replacement. If you have more than one car transmitter for your garage door, then your other transmitters will likely need new batteries soon as well, since they were probably installed around the same time.
On our EZ-Set Torsion Springs page you will find several options for replacing these springs. We also have step by step instructions for EZ-Set Torsion Spring Replacement. In addition, one of our customers has provided excellent EZ-Set Torsion System instructions for removing the spring without wrecking the winding unit that secures the stationary cone. Instead of a spanner tool, you may prefer to use a pipe wrench or large channel locks to hook the end of the spring and remove it from the cones in the last step.
A new garage door can add serious curb appeal, not to mention myriad home safety benefits. The cost of a new garage door will vary based on the type of garage door you want and the materials it will be made of. You can purchase a new garage door and have the pros install it for you, but proceed with caution as many installers won’t guarantee their labor if you didn’t purchase the garage door through their company. A new door (without installation) may cost anywhere from $200 to $4,000 or more, depending on size, brand and materials. Here are some examples of average new garage door costs, including installation:  
There are many steps to replacing torsion springs, but overall it's a simple, straightforward process. If you're inclined to attempt it, find a good online video tutorial (preferably done by a garage door pro) that walks you through the entire process, including how to buy the right size of springs. You can also buy new springs and any related parts online, along with the most important items that you need: the two solid-metal winding rods that you use to wind and unwind the torsion springs.
Widths - in addition to doors coming in a range of styles, they can be found as double-width and single-width styles. There are some serious considerations when opting for one over the other. For example, if a homeowner decides to use a single door that covers the entire opening of a two-car garage they will have to make serious structural modifications to the entry way;

7.3 Slide both torsion springs out above the top of the garage door toward the cable drums. Notice that there is only one bushing or bearing between the cones. Sometimes a single bearing is pressed into the bracket; other brackets have a single bearing or bushing that fits in either cone. Do not try to install a bushing or bearing in both of the stationary cones. You will risk breaking a cone. The purpose of the bushing is to keep the shaft from wearing against the spring anchor bracket. Only one bushing is needed to accomplish this.


If the door won’t move at all because of an alignment issue, then this problem isn’t one that you should try to tackle yourself. A garage door professional will have the necessary equipment needed to safely realign and repair your garage door. Additionally, if the track misalignment is beyond repair, a professional can install a new garage door track for you. http://youtube.com/e/Z_eZc-kh40c
×