"Our garage door wouldn’t shut on sunny days and the tech came out. He explained my options (swap the “seeing” sensor with the other, or replace them). He tried swapping and it was still an issue so he replaced them. In addition, he adjusted the spring because the company that installed it last year did not adjust it properly. He was here for about two hours and charged us for only the sensor replacement. Will definitely be using this company again! Highly recommend them. "
When you install a new garage door, replace all the hardware as well. If your automatic opener doesn’t have an automatic reversing system that includes photoelectric eyes, replace it. Doors with openers also require two extra pieces of hardware that you’ll see in Photo 4: a support strut (usually included in the door kit) and an opener bracket (not included). For doors with torsion springs located over the door, spend the $50 or so to have a garage door professional release the tension.
The problem is that one of the garage doors "catches" (i.e. stops) while going up at about 2 feet off the ground ~90% of the time. When the button is pressed again, it goes all the way down. This cycle can be repeated ad nauseum, or I can give the door a gentle tug upward just before the "Sticking" point, and this will give the door enough "impetus" to make it all the way up. http://m.youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c
After working on the car, you find a big oil stain on the driveway. Pulverize a scrap piece of drywall with a hammer (any new home construction site will have dumpsters full of waste pieces of drywall). Crumble the pulverized drywall with your hands and sprinkle on the stain. Leave it overnight, and rinse off in the morning. Reapply and brush in with a bristle broom in cases of stubborn stains.
11.2b If the springs you installed are too strong, and if you wind the springs the correct number of turns, the door will not stay down nor half way. The garage door will be hard to close. DO NOT REMOVE MORE THAN HALF A TURN OF SPRING TENSION TO CORRECT THE PROBLEM. Here's why. If you remove 3/4 of a turn to get the door to stay closed, and then if you open the door, it will get heavier as you open the door, and once open, the cables will come off the drums. This could create as much as a day's extra work. It could also cause door damage and/or result in serious injury. Do not use the door! Get different springs!
10The type of garage door shown provides the necessary lift assistance with a “torque tube.” If you intend to use an opener, wait to install the tube. Otherwise, install the torque tube according to the manufacturer’s directions. Roll up the door about 4 feet to check for the alignment of the tracks, and make any adjustments. Then tighten all fasteners.

Garage Door Repair Free Estimate Centennial Colorado


If you have a Wayne Dalton TorqueMaster system (pictured below), the springs will be inside a tube. The only way to determine if one is broken is to lift the garage door manually. If the door is heavy (roughly 60lbs for a double car door), you most likely have a broken spring inside the TorqueMaster tube. Another way to tell if you have a broken spring in your Wayne Dalton Torquemaster tube is if the door goes up and won't go back down. http://m.www.youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c
The problem is that one of the garage doors "catches" (i.e. stops) while going up at about 2 feet off the ground ~90% of the time. When the button is pressed again, it goes all the way down. This cycle can be repeated ad nauseum, or I can give the door a gentle tug upward just before the "Sticking" point, and this will give the door enough "impetus" to make it all the way up.
When it comes to garage doors, functionality and safety are equally important in the eyes of Sears Garage Door technicians. Our associates know the importance of garage door safety and the hazards that a faulty garage door can pose for your family. To confirm that your garage door and opener operate safely, our technicians perform a 20-point safety check during maintenance calls and repair jobs. This safety check verifies that any repair work performed has been done correctly and that there are no lingering safety problems with your door and mechanisms. If our technician discovers any safety concerns, he’ll advise you on the best way to proceed with correcting the problem.

Automatic Garage Door Repair Centennial Co 80016


Test the garage door opener while the door is down. Push the wall button to operate the door opener. If the opener operates, the binding was setting the internal safety mechanisms off, alerting the opener not to close. Raise the door slightly and jiggle the emergency cord to lock the carriage back over the carriage base, and attempt to operate the door with the motor.

Step 1: Check the metal tracks inside the garage. Look at the mounting brackets that hold the tracks to the walls. If they're loose, tighten the bolts or screws at the brackets. Working inside the garage with the garage door closed, examine the tracks for dents, crimps, or flat spots. If there are any damaged spots, pound them out with a rubber mallet, or with a hammer and a block of scrap wood. If the tracks are badly damaged, they should be replaced.

Sectional: Also known as a raised panel door, this door is the most common. It is made of several horizontal panels hinged together, fitted with wheels and mounted within a track. The biggest advantage of this door is it takes up relatively little space and easily controlled with a standard remote garage door opener for a nominal cost. Their moving parts are readily accessible which can keep repair costs low. The average cost for sectional door repairs is $128.
If you have decided to replace your springs, if you are sure your door had the correct springs, and if you are ready to buy new ones, we recommend that you measure your spring or springs following the instructions in Step 4 below. Measuring springs can be difficult; most individuals, even garage door technicians, sometimes have difficulty measuring torsion springs. Ordering incorrect springs wastes time and money. http://youtube.com/v/Z_eZc-kh40c
×