Single panel doors are constructed from one monolithic panel. From the closed position a single panel door swings up and overhead with a hinge on each side (known as jamb type hardware) to the fully open position. A disadvantage of monolithic panel doors is that the swing up arc of the door occurs partially outside the garage. This means a vehicle must stop and park several feet in front of the door to avoid being hit by the garage door when it is opened.


When you install a new garage door, replace all the hardware as well. If your automatic opener doesn’t have an automatic reversing system that includes photoelectric eyes, replace it. Doors with openers also require two extra pieces of hardware that you’ll see in Photo 4: a support strut (usually included in the door kit) and an opener bracket (not included). For doors with torsion springs located over the door, spend the $50 or so to have a garage door professional release the tension.
The national average for garage door repair cost is between $80 and $110. Some of the factors that affect your garage door repair cost are the type of springs (most often torsion or extension), the size and weight of the door, and the door material. Many garage door pros will charge a service fee to visit your house and determine the problem. Often, the service fee includes a set amount of labor. One example of this is an $80 service fee that includes the first hour of work plus testing and inspecting your garage door and garage door opener, while another pro may charge $150 for the same standard service call.    https://m.youtu.be/Z_eZc-kh40c

Disclaimer: NerdWallet strives to keep its information accurate and up to date. This information may be different than what you see when you visit a financial institution, service provider or specific product’s site. All financial products, shopping products and services are presented without warranty. When evaluating offers, please review the financial institution’s Terms and Conditions. Pre-qualified offers are not binding. If you find discrepancies with your credit score or information from your credit report, please contact TransUnion® directly.
The Leading (scam) in the industry is the "LIFETIME WARRANTY". It sounds great when presented and seems fair and maybe even a good idea even though the initial cost seems pretty high (on average 450 - 700 dollars) what is not mentioned is the annual required cost (known as the required or annual door maintenance) to keep the warranty valid which if a standard 15,000 cycle spring/s is used should average Ten years, this annual service is usually 90 - 120 dollars. That would be another "900 - 1200" dollars invested in Ten years, that and the initial cost and you could buy two or more "complete new" doors in that time.
Loosen the set screws while holding each spring with a winding bar. Position a sturdy ladder to the side of the springs, rather than working directly in front of them, for safety reasons. Put on eye protection and leather gloves. Push a winding bar into the bottom hole of the winding cone on the outside of 1 spring. Use a wrench to loosen the 2 set screws. Keep a firm grip on the bar as the the spring will expand powerfully as the screws are released. Repeat on the other side.[2]

I got these replacement cables for my beach house garage door after the originals rusted and broke. These are twice the diameter of the OEM cables, and fit the door perfectly. The larger cables give piece of mind for both supporting the door and providing safety cables for the extension springs. Came with all the necessary hardware, and the installation was easy with the doors blocked in the up position.
Next, check to see if your garage door operator is the problem. Do this by pulling the emergency release cord when the door is in the down position (so the door doesn’t come crashing down in case there is a problem). Then, try to lift the door up manually. Does it open easily? If so, your opener is probably at fault. If it still doesn’t move, the problem likely lies with your tracks, springs, or rollers.

Garage Door Repair Free Estimate Centennial Colorado 80016


Replacing torsion springs is done with the door closed. You start by carefully unloading all of the springs (most standard-size doors have two; any broken spring will already be unloaded), using the winding bars. Then, you unbolt the springs from the central rod bracket, disconnect the cables from the pulleys, and loosen the pulleys and slide them off of the rod. Next, you swap out the springs, reinstall the pulleys and cables, and secure the inside ends of the springs to the central bracket. Finally, you wind up both springs (securing them with two setscrew bolts on the winding cones) and test the door for proper spring tension. Often, springs need an extra quarter-turn or two to get the door balance just right.

Garage Door Repair Companies Centennial Colorado 80016


If you have two torsion springs on your garage door, the good spring will most likely keep the cables on the drums when the other spring breaks. This makes it much easier to lift because the good spring will be pulling half the weight of the garage door. You can also use the garage door opener to help assist while someone lifts the door and acts as the broken spring. Use extreme caution when doing this to prevent damage to your garage door or injury to a person.

Automatic Garage Door Repair Centennial Co


What LCD said is more or less right. Those are the ranges you'd typically find you will have to pay, but it's important to remember that the rates vary across the country. One thing I always advice others to do is to get quotes from different contractors. It might not be the biggest job, but you'd be surprised how much difference there typically is in the quoted prices. If you check out the link I put in the resource, it'll take you to a site where you can get quotes from 4 different contractors at once. Under "Select service" you simply pick "Spring Replacement".

Ace Garage Door Repair Centennial Colorado 80015


Our garage door broke 3 days before Christmas, trapping my car inside. We contacted our home warranty, and within 24 hours, Sears called with an appointment time for the next day! I was so impressed! I thought, for sure, with the holidays, we would have to wait. When the technician showed up, he was so friendly. Unfortunately, the repair was not covered under our warranty, but he was able to help us get a good deal on a new spring and still make the repairs that day before he left. He also gave us great advice on how to keep the spring lubricated so it would not break again. I felt like he really went above and beyond to provide great service. Since moving into this new house in August, we have used Sears for several things now, and have been very pleased with the service. It's nice to see that in an age when so many companies just put customer service on the back burner in order to meet their bottom line, Sears still really cares and makes their customers feel important. Thanks for taking care of us this Christmas!
Sometimes, you’ll notice that your garage door closes all the way and then immediately goes back up instead of staying in the closed position. This issue usually arises with brand new garage doors that were just installed or older models that may need to be reset. If this happens, the most likely culprit is the open and close limit settings of your garage door opener.

Every thing the tech demostrated was helpful, he knew how to do his job even if his eyes were shut. Very knowledgeable, took time out to explain every detail about the install process. Very highly satisfied. A d would love to have him for future additional repairs. Would definitely recommend sears and would use you guys again thanks mr.technician for a job well done.
CAUTION! Replacing garage door torsion springs is dangerous because the springs are under tension. If you do not use the right tools and follow safe procedures, you could lose hands, limbs or even your life. You could also damage property. We want your business, but not at the expense of your well being. Doing the job right is your responsibility. If you have any doubts about your ability to safely change your springs, we recommend you hire a professional to repair your garage door. Safety First! Then work.

Garage Door Repair Emergency Centennial Colorado


Garage door springs can break for a variety of reasons. Extreme heat or cold, for instance, can stress the springs to the point of breaking, or it could be that normal wear on older springs could cause them to break. Whatever the situation, a broken spring can render your garage door inoperable. Your door will not be able to open or close when a spring is broken, and you should stand clear of your door until a professional can assess the situation and correct it.

Just like on a bike sprocket, your cables can sometimes become disengaged. Oftentimes, when a torsion spring breaks, the garage door cable will snap as a result. Sometimes, the cable will cause damage to a vehicle or wall, and if a person happens to be in the way of the cable it can cause serious harm. If you cables have snapped, you should call a professional to help you. See the video above.

From a big-box store, basic garage door cables can run between $8 and $20, depending on the product. Your pro may charge you a different cost if they provide the cables. Your cables may not need to be replaced if they have simply come off the track, but broken cables will need to be completely removed and replaced. In either instance, the pros will need to secure or take down the door; unwind the springs; reset or replace the rollers, cables, and drums; and then wind the springs once more. For example, a pro could reset cables that have come off the track for $129.99. The average national cost for a garage door repair specialist is $80 - $110 per hour and the typical cost to replace a broken garage door cable is anywhere from $130 to $200.
Doors with extension springs have two sets of pulleys (which are sometimes called sheaves): one at the end of each spring and one at the top of the vertical door track. They also have two cables on each side. One cable attaches to the bottom of the door, runs up and over the pulley above the door and around the spring pulley and then attaches to the door track bracket. The other cables are safety cables that run through the middle of the springs and are fixed to a track bracket at both ends. These cables restrain the springs if they break under tension. All extension springs must have safety cables.

Aaa Garage Door Repair Centennial Co 80015


"Mile High garage called shortly after submitting my request and set an appointment to have a repair man show up shortly after. They went over everything I needed to get done and gave me several pricing options to fix initial need and alleviate future issues. Work was done in a timely manner and customer service was great. Mile High garage called shortly after submitting my request and set an appointment to have a repair man show up shortly after. They went over everything I needed to get done and gave me several pricing options to fix initial need and alleviate future issues. Work was done in a timely manner and customer service was great. "

Garage Door Repair Guy Centennial Co 80016


Changing your garage springs isn’t typically a DIY project and usually requires a professional. But it’s good to know when it’s time to find garage door spring replacements. To test your springs, disable your garage door opener if you have one, then raise the door manually. If it doesn’t stay in place on its own, it’s time to replace your garage springs.
Your dream car is parked in out of the elements, but it's not secure because the garage door won't lock. Most garage doors have two horizontal bars that move out from the center of the door into slots along the side of the door in the door track, effectively locking the door in place. Over time, these bars can shift slightly out of position so that they are no longer correctly aligned with the locking slots. To realign the bars, unscrew the guide brackets on the edges of the door so that they are loose enough to move, and then reposition them so that they smoothly guide the locking bars into the locking slots. Lubricate the lock mechanism with machine oil and you're done.
If your garage door goes up and down in a jerky motion, you might have one broken spring on a two spring system. Some garage door openers are strong enough to lift a door with only one good spring. The “herky jerky” motion is especially common with garage doors equipped with extension springs. It might be something as simple as lubricating your garage door pulleys, hinges, and rollers. When in doubt or if something doesn’t feel right about your door, call a service company to have it serviced.

After working on the car, you find a big oil stain on the driveway. Pulverize a scrap piece of drywall with a hammer (any new home construction site will have dumpsters full of waste pieces of drywall). Crumble the pulverized drywall with your hands and sprinkle on the stain. Leave it overnight, and rinse off in the morning. Reapply and brush in with a bristle broom in cases of stubborn stains.
Scott was exceptionally polite, professional and knowledgeable. He thoroughly checked my garage door opener, but also inspected the garage door itself and pointed out rust and deterioration that has occurred. Scott then gave me a quote on a new garage door, explaining the installation procedure and quality elements of the new door including the warranty. I was very pleased with the entire service appointment, and my husband and I are seriously considering the new garage door, but only if Scott is the installer! Thanks, Scott!

Your dream car is parked in out of the elements, but it's not secure because the garage door won't lock. Most garage doors have two horizontal bars that move out from the center of the door into slots along the side of the door in the door track, effectively locking the door in place. Over time, these bars can shift slightly out of position so that they are no longer correctly aligned with the locking slots. To realign the bars, unscrew the guide brackets on the edges of the door so that they are loose enough to move, and then reposition them so that they smoothly guide the locking bars into the locking slots. Lubricate the lock mechanism with machine oil and you're done.


Sears Craftsman Garage Door Openers are America’s favorite. We have several options to choose from that will fit your individual needs. Sears garage door opener selections includes 1/2 horsepower, 3/4 horsepower, belt and chain drive as well as the Craftsman Smart Control garage door opener which allows you to control and monitor your garage door even when you are away from home. https://m.youtube.com/v/Z_eZc-kh40c
×