SNAP... bang... boom. That is the sound of a garage door torsion spring breaking. It can be a very loud noise that sounds like a firecracker or gunshot. Springs are rated for a certain number of cycles and are the first thing that will break in your garage door assembly. Broken springs are the #1 source of customer calls for garage door repair companies. If you have a broken spring, you should NEVER try to open the door, as it can be very dangerous. This repair should be left to a professional or someone with the right tools and skills.
Measure the length of the relaxed spring. Unfortunately, you can’t measure the springs while they’re installed as the tension on them would provide you with the wrong measurement. Now that you’ve removed the springs, use a tape measure to find the length of the entire spring, from one end to the other. You’ll need this information in inches to order replacement springs.[6]

The U.S. Consumer Product Safety Commission says that about 30,000 injuries linked to garage doors are now reported every year in the United States. Many of these injuries have involved bruised or broken extremities. However, some have included serious shoulder, back, and head injuries leading to permanent disability or even death. What is the cause of these garage door injuries? One leading cause has been homeowners trying to repair or replace their own garage door springs.
The tricky parts of the job involve you carrying the tension of the spring. Replacing a spring requires that you first unwind the spring to relieve the tension, then wind it back up and secure it while it's under tension. Winding bars are used for all winding and unwinding actions—don't try to save a few bucks by substituting long screwdrivers or pieces of rebar for the real winding bars. Substitute tools are much more likely to slip, or they may bend or break under the load of the spring. https://youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c
Most residential garage doors have one of two types of springs: torsion or extension. Torsion springs are heavy-duty springs mounted to a metal rod that runs parallel to the door, directly above the door opening. These springs are loaded, or tensioned, with a twisting action. When the door closes, cables attached to the bottom corners of the door pull on pulleys attached to the ends of the metal rod the springs are mounted on. The pulleys turn the rod, which twists the springs and creates tension. When the door is opened, the springs unwind and help lift the door.
When you're done watching this video you'll know how to determine whether the company you hired to replace your garage door spring installed the right size spring on your door. You'll also learn the consequences to your garage door opener if the wrong size spring is used. If you are having a problem with your garage door spring, the 2:30 minutes you spend watching this video is time will spent. https://www.youtube.com/watch?feature=youtube.be&v=Z_eZc-kh40c
6.13 Lower the second bar to the top of the garage door as you did the first bar. If your shaft is distorted inside the cone, you may need to tap the bar with a hammer as you unwind the spring. Maintain a firm grip on the bar; keep it firmly inserted completely into the cone; and be prepared at all times for the cone to slip, break, explode or snap loose from the shaft and jolt the bar down.

Automatic Garage Door Repair Centennial Co 80015


Door styles - in addition to the styles just mentioned, it is important to also consider additional features such as windows across the top of the door to provide light inside of the garage, the use of steel or wood frames to give decorative doors added security and stability, and insulation which can reduce energy costs in the attached garage by an impressive 15 to 20%; and

Garage Door Repair Near Me Centennial 80016


The technician did a wonderful job - arrived on time and completed the job in less than 2 hours. I would have given him a 5 on everything if he had returned to add the additional piece (a piece that is fixed to the door frame for better insulation) to my door on the outside on the day he said he would come back. The piece he brought was of wrong color and he said he would be back with the right color the first day after New Year's Day to put up the piece. I hope he can come back soon.

Ace Garage Door Repair Centennial Co


Good response time and service; Question - I googled to find the Sears Garage Door repair phone number. During the conversation, I was unsure if this was "Sears" or a "contractor service" or other service. I had to ask if this repair person was coming from "Sears" or an independent repair. I was concerned until the service man arrived in a sears truck wearing Sears apparel. You might want the process to be more clearly identified as Sears.

7.5 Slide both springs out toward the cable drums. This is often the hardest part of the job. You may need to file away swollen shaft, set screw burs, drywall or paint. If the shaft is distorted because the garage door installer overtightened the set screws, file the shaft, insert a bar into the cone and tap the bar with a hammer until the cone passes over the enlarged portion of shaft.
What LCD said is more or less right. Those are the ranges you'd typically find you will have to pay, but it's important to remember that the rates vary across the country. One thing I always advice others to do is to get quotes from different contractors. It might not be the biggest job, but you'd be surprised how much difference there typically is in the quoted prices. If you check out the link I put in the resource, it'll take you to a site where you can get quotes from 4 different contractors at once. Under "Select service" you simply pick "Spring Replacement".

Ace Garage Door Repair Centennial Colorado 80015


9.12 It is now time to secure the torsion springs in the middle. For various reasons, many installers will offset the center bracket several inches from the center of the door. Offsetting the bracket makes it easier to work around the opener bracket without causing any problems in the operation of your garage door, but offsetting the bracket is not necessary. If you have a slotted center bracket, remove the vise grip and lube the shaft where it turns inside the bushing. Position the shaft so it is the same distance from the header as it is at each end. The shaft should be straight and parallel to the header.

Garage Door Repair Cost Centennial Co


9.9 Go to the other side of the garage door and insert the end of the cable into the drum. Rotate the drum until the cable is tight. Slide the drum against the bearing and push the shaft to the right. The marks should line up. If they don't, figure out why and correct the problem. It could be a stuck cable, the garage floor may have shifted, or the vertical angle that helps support the bearing plate may have loosened and shifted. Many garage doors have been installed with a gap between a drum and a bearing plate. The cable drums should always be flush against the race of the bearings.
Nothing can be more frustrating than trying to open or close your garage door, but have it get stuck halfway. The most common reason this happens is due to a broken torsion spring, a part that is responsible for providing balance. It is a common problem that has many people saying “My garage door has a broken spring or is stuck, what do I do next”? If you are in this same boat, you’ll find the information below very useful. 

These instructions were first posted in 2005, and they were updated in August of 2008. I have been frank about the hazards of garage door repairs and about my own accidents incurred while replacing torsion springs. For what it's worth, you might be surprised to know that I, too, have benefitted from producing these instructions. I have not had any garage door accidents since we first published these on the web in 2005. And, in as much as I have helped keep other DIY-ers out of the emergency room, I consider myself somewhat of a medical practitioner.

Asap Garage Door Repair Centennial Co


Maybe the battery died or a spring broke, but you can't get into the garage to even see what the problem is. If the garage door is the only way in or out, or if you can't find the key to the door, you'll have to either find a way to break in or call a locksmith. As a preventative measure, it's smart to keep a spare key or install an emergency key release that would allow you to release the emergency disconnect to the operator so you can manually raise the door. https://youtube.com/embed/Z_eZc-kh40c
×