Examine the garge door rollers, hinges, tracks, and other hardware for signs of damage that might cause the door to hang up. Lubricate the tracks and hardware with silicone spray or oil. Raise the door slowly, watching it as it lifts. See if it catches on a warped panel or support beam or if an obstruction in the path of the photo eye causes it to stop or reverse. Any part that protrudes into the path of the garage door can cause it to stop.

Garage Door Repair How Much Centennial Co 80016


8.5 Inspect the bearing. Lube it with motor oil, spray lithium, or spray lubriplate grease. Do not use WD-40. If the shaft is worn and the bearing is seized and you can't free it, replace the bearing. Or, if you have bearings labeled "ADH" we recommend replacing them. I find very few other bearings that need to be replaced. However, if you do need to replace the bearing and you do not have a new one, you can replace it at a later date. You'll find a quick way to do this at our End Bearing Plate Replacement instruction page.
If the door only goes up six inches and stops, or moves very slowly when using your remote, you could have a broken spring as well. Some customers will notice that the top section of their door is bent or that the door falls very quickly when lowering. Your door may be “crooked” or jerky when going up and down, and both of these signs indicate your torsion spring is in poor condition and very likely to break in the near future. Any time you hear a loud “popping” noise while operating, you should inspect your torsion spring immediately for signs of damage.
If you need to leave the door open until you can make repairs, block the door track on both sides so the door can't move, and unplug the garage door opener (if you have one). If you want to close the door, you can try closing it with the opener, making sure there's nothing in the door's path in case something goes wrong. However, this will put some strain on the opener. Alternatively, you can have a few strong helpers hold the door while you disconnect it from the opener and carefully close the door manually—again, it will be very heavy.

Garage Door Repair And Service Centennial Co


There are many steps to replacing torsion springs, but overall it's a simple, straightforward process. If you're inclined to attempt it, find a good online video tutorial (preferably done by a garage door pro) that walks you through the entire process, including how to buy the right size of springs. You can also buy new springs and any related parts online, along with the most important items that you need: the two solid-metal winding rods that you use to wind and unwind the torsion springs.

ryan was way more than early when he showed up. ryan gave me a straight up, not nonsensical "ah..ah..." like someone making up a story to listen to. direct and to the point, like a professional, gave me my options that i could present to the boss. the boss didn;t like the price of the new rollers. but she loves that it doesn't sound like a tank coming home from war. we were completely unprepared for this, so, it's good we got a guy like ryan.
The two main garage door operating mechanisms are sectional roll-ups or tilt-ups. Garage door repair services can fix single-car, double-car or RV-height doors. Your garage door may be made of wood, steel, aluminum, masonite, vinyl, fiberglass or another material. The type of garage door repair you need really depends on the type of garage door you have and the issue at hand. Garage door repair pros often charge a flat service call fee to diagnose the problem and provide an estimate. For customers who choose to have the repair done, the service call fee may be applied to the first hour of labor (including time to make the diagnosis). If your garage door is under warranty, the repair may be free of charge. https://www.youtube.com/v/Z_eZc-kh40c?version=3

Garage doors provide one of the major entryways into your home. Therefore, it is essential to ensure that they are secure and in good working order. If you are having problems with your current door, then you need to have a professional determine if it can be repaired or if it will need to be replaced. Here are some of the most common factors that will affect the cost of a garage door repair.
Our garage door broke 3 days before Christmas, trapping my car inside. We contacted our home warranty, and within 24 hours, Sears called with an appointment time for the next day! I was so impressed! I thought, for sure, with the holidays, we would have to wait. When the technician showed up, he was so friendly. Unfortunately, the repair was not covered under our warranty, but he was able to help us get a good deal on a new spring and still make the repairs that day before he left. He also gave us great advice on how to keep the spring lubricated so it would not break again. I felt like he really went above and beyond to provide great service. Since moving into this new house in August, we have used Sears for several things now, and have been very pleased with the service. It's nice to see that in an age when so many companies just put customer service on the back burner in order to meet their bottom line, Sears still really cares and makes their customers feel important. Thanks for taking care of us this Christmas!
Roller doors ("Sheet Doors"-USA) are usually constructed of corrugated steel. They evolved from cover window and door coverings.[4] Other materials can be used (e.g.; transparent corrugated fibreglass) where strong impact resistance is not required. Corrugations give the door strength against impacts. A typical single car garage roller door has a preloaded spring inside the rolling mechanism. The spring reduces the effort required to open the door. Larger roller doors in commercial premises are not sprung (except USA) and use a manual pulley and chain system or a geared motor to raise and lower (roll up and roll down) the door. Roller doors cannot be effectively insulated.
Squealing, screeching, or grinding noises from your garage door are usually indicative of a lack of lubricant or an accumulation of dirt or debris in the tracks. When removing debris, do not use harsh chemicals to clean the tracks. Once the track is clean, coat it with lubricant designed especially for garage doors, if possible. If you do not have access to this special type of lubricant, you can use WD-40 on the tracks and hardware.
Inspect the area around your garage door to see if something is blocking the photo eye sensors. Then look at the tracks to see if there is any buildup on the inside. You’ll need to get a step ladder to look at the tracks on the top part of your garage, as it will be difficult to see from ground level. It may also not be a bad idea to proactively wipe down your garage door tracks periodically to prevent this type of buildup from occurring. Running a damp rag along each track should be enough to remove anything that’s lingering on the tracks.

Garage Door Repair Centennial Co


After you’ve ordered your new garage door, we’ll perform a site inspection to confirm your door size. We’ll contact you to schedule the installation, and our professional installers will do the rest. They’ll deliver your door, take down the old door, reconnect your opener if there is one, seal your perimeter and provide a final walk-through where they’ll clean up the area and haul away your old door. Additional fees for haul away may apply in some markets. We are happy to provide answers to questions you may have at the time of your garage door and opener installation.
"Our garage door wouldn’t shut on sunny days and the tech came out. He explained my options (swap the “seeing” sensor with the other, or replace them). He tried swapping and it was still an issue so he replaced them. In addition, he adjusted the spring because the company that installed it last year did not adjust it properly. He was here for about two hours and charged us for only the sensor replacement. Will definitely be using this company again! Highly recommend them. "

Garage Door Repair Installation Centennial Co 80016


If your garage door goes up and down in a jerky motion, you might have one broken spring on a two spring system. Some garage door openers are strong enough to lift a door with only one good spring. The “herky jerky” motion is especially common with garage doors equipped with extension springs. It might be something as simple as lubricating your garage door pulleys, hinges, and rollers. When in doubt or if something doesn’t feel right about your door, call a service company to have it serviced. 

Garage Door Repair Free Quote Centennial 80016


If the track is misaligned, but the door still moves, there are a few things you can do to attempt to remedy the issue on your own. You’ll know that it’s misaligned if you hear a rubbing noise when the garage door reaches a certain spot on the tracks each time it opens and closes. Sometimes the door may even slow down slightly when it hits this spot.
The winding and unwinding is done at a metal fitting, called a winding cone, attached to the outside end of the spring. You stick a winding bar into one of the four holes in the cone and use the bar as a lever to turn the cone. Once you've completed a quarter turn, insert the other bar into a different hole in the cone and let the bar lever against the closed garage door to hold the spring tension. This allows you to move the original bar to repeat the process, alternating the bars with each quarter-turn. It takes about 30 quarter-turns to fully tension a standard torsion spring.
After you’ve ordered your new garage door, we’ll perform a site inspection to confirm your door size. We’ll contact you to schedule the installation, and our professional installers will do the rest. They’ll deliver your door, take down the old door, reconnect your opener if there is one, seal your perimeter and provide a final walk-through where they’ll clean up the area and haul away your old door. Additional fees for haul away may apply in some markets. We are happy to provide answers to questions you may have at the time of your garage door and opener installation.

Garage Door Repair Companies Centennial Co 80016


Does your door stop when going up? Does your look crooked? Can you see a break in the spring that runs along the side of the tracks? You might have a broken extension spring. Extension springs are generally used on smaller doors like an 8×7 or a 9×7. Extension springs are attached to the bracket that holds the horizontal track to the ceiling. The extend as the door goes down and with one broken the door cannot work properly. Typically one spring is broken and the other is not, however, we would replace both. They have both been used the same amount and springs break based off of usage.

Garage Door Repair Free Estimate Near Me Centennial 80015


It is very important that the replacement springs are calibrated for the weight of your door. Using the wrong size garage door springs will caused the to not function properly and could also cause the opener to break much quicker. Replacing extension springs can be very dangerous and if done wrong can harm someone using the garage door. Make sure you call the Garage Door Doctor to ensure your garage is repaired properly!


The average lifespan of torsion springs is determined by its cycle count. Garage Door Medics provides springs with an average of 25,000 cycles and we can provide custom size springs for any door. The industry standard is 10,000 cycles. When a garage door is used more frequently, the springs may not last as long. If you begin to see signs of wear, it’s time to give Garage Door Medics a call!
Overhead Door Company of Central Jersey has been in the garage door industry since 1972. Our proficient service technicians offers the best installation, maintenance and replacement for your garage doors and parts. You can check our our Before and After residential garage doors photos for reference. Kindly click on "Schedule at-home appointment" below to get started.
On our EZ-Set Torsion Springs page you will find several options for replacing these springs. We also have step by step instructions for EZ-Set Torsion Spring Replacement. In addition, one of our customers has provided excellent EZ-Set Torsion System instructions for removing the spring without wrecking the winding unit that secures the stationary cone. Instead of a spanner tool, you may prefer to use a pipe wrench or large channel locks to hook the end of the spring and remove it from the cones in the last step.
On one-piece doors with side springs, you open the door to relieve the spring tension, and simply swap out the springs on the opener-arm mechanism; there are no cables or pulleys to deal with, and the springs have internal safety rods. Some doors have tensioners that maintain moderate tension when the door is open all the way, and on these you'll have to loosen the tensioner in order to remove the spring.
Refrain from parking your car in the garage until the garage door is repaired. Additionally, try not to open and close the door while it’s in this condition. With that amount of possible force coming from the springs or cables, they could potentially damage your vehicle or other property in the garage as well as cause serious injury. It’s especially important that you and your family stay away from these cables or springs until everything is repaired.
10.13 Slowly pull down on the winding bar until the garage door rises 3" and the roller hits the vise grip on the track. The door will usually drop back down and raise the bar. If it doesn't, lift the end of the bar until the door closes. If the door comes up by itself when you hold the bar lightly, the springs are either over wound or they are too strong. You may need to remove 1/4 to 1/2 turns from the springs. If the door comes up on its own, you either have to many turns on the springs or you have the wrong springs. This can be very dangerous. We recommend getting professional help. Removing the winding bar could cause the garage door to knock you off the ladder.
Garage door manufacturers typically produce garage doors fitted with torsion springs that provide a minimum of 10,000 to 15,000 cycles and are guaranteed for three to seven years. One cycle is a single opening and closing sequence. Most manufacturers offer a 30,000 cycle spring. However, it is important to remember that if the weight of the garage door is increased by adding glass, additional insulation, or even several coats of paint, the life of the torsion spring may be greatly reduced. Additionally, springs at highly humid environments, such as coastal regions tend to have a significantly shorter cycle life, due to the corrosive cracking.

Both types of springs are loaded, or under tension, when the door is closed. This gives them stored energy to help lift the door as it's being opened. When the door is all the way up, the springs are relaxed, or relatively so—they still may be under some tension. The mechanical difference between extension and torsion springs is that extension springs are loaded by stretching, or elongating, while torsion springs are loaded by twisting, creating torque.


You may remember a time as a kid when you and your siblings would close the garage door and run underneath it as fast as possible to make it out before the door closed. Well, on any garage door installed after 1993, that’s no longer possible thanks to two tiny photo eyes on either side of the garage entrance. These photo eyes transmit an invisible beam between each other that detects if anything is in the garage door’s path when it closes. This safety measure is there to prevent automatic garage doors from closing on top of someone or something and causing serious injury or damage to property. https://www.youtube.com/watch?v=Z_eZc-kh40c&feature=share
Another scenario is the garage door goes up very slowly when using the automatic opener. Some garage door openers have DC motors that start off slow when opening and then kick into a higher speed. If you have a broken spring, the opener might stay in the slower speed due to the heavy weight of the garage door. If this happens to you, close the garage door and pull the emergency release rope. Next, try to lift the door. If it is really heavy, then you most likely have a broken garage door spring.
A garage door spring replacement should cost between $175 and $225 for a single tension spring and between $250 and $300 for two tension springs. Most garage door companies carry a wide enough variety of spring sizes to cover most residential doors. As long as the proper amount of turns are put on the spring, there are more than one correct springs to use for any one door.

In order to prevent injury, garage doors automatically reverse if they come into contact with an obstacle. When the door closes halfway but then reverses for no apparent reason, this may be a sign that there is something preventing it from closing, something that you can't see. Check the tracks for stuff like dirt, rocks, bits of trash, or other debris. Give the tracks a wipe-down to dislodge anything that might be getting in the way. https://youtube.com/watch?v=Z_eZc-kh40c
×