There are lots of ways your garage door can suffer damage. The tracking might be rusted or broken, the weatherstripping might need to be replaced or the door itself might actually be broken or have a hole in it. After all, garage doors are sturdy but not unbreakable. One component of your garage door in particular that will likely need replacing every so often is the spring.
Locating a contractor - there are many professional overhead garage door companies. It is always advisable to contact at least three different agencies and request a bid or quote for the work. Be sure that each quote includes the costs for a few different types of doors, any installation fees, and the cost of wiring the electronic openers. Standard prices range from: https://www.youtube.com/watch?v=Z_eZc-kh40c&app=mobile
The nucleus of any garage door system is its opener. Easily overlooked, garage door openers are highly complex pieces of equipment, often containing dozens of intricate parts that work simultaneously with one another to consistently raise and lower your door. You'll know that you're getting the best from Sears as it's the home to America's #1 Garage Door Opener Brand, Craftsman*.

7.5 Slide both springs out toward the cable drums. This is often the hardest part of the job. You may need to file away swollen shaft, set screw burs, drywall or paint. If the shaft is distorted because the garage door installer overtightened the set screws, file the shaft, insert a bar into the cone and tap the bar with a hammer until the cone passes over the enlarged portion of shaft.
11.2b If the springs you installed are too strong, and if you wind the springs the correct number of turns, the door will not stay down nor half way. The garage door will be hard to close. DO NOT REMOVE MORE THAN HALF A TURN OF SPRING TENSION TO CORRECT THE PROBLEM. Here's why. If you remove 3/4 of a turn to get the door to stay closed, and then if you open the door, it will get heavier as you open the door, and once open, the cables will come off the drums. This could create as much as a day's extra work. It could also cause door damage and/or result in serious injury. Do not use the door! Get different springs!
There are two types of garage door springs: torsion and extension. Torsion springs are horizontal and located near the top of the garage door. Check for a gap between these springs indicating a break. Springs on the sides of the garage door are extension springs. Inspect them to see if one or both of them have broken. If you have a broken spring, call a garage door technician to fix it for you as soon as possible. Never operate a garage door with a broken spring; it could severely damage the door and the operating system. Never attempt to replace a broken spring on your own, either. Replacing broken garage door springs is very dangerous for anyone other than a certified, professional repair technician.

The winding and unwinding is done at a metal fitting, called a winding cone, attached to the outside end of the spring. You stick a winding bar into one of the four holes in the cone and use the bar as a lever to turn the cone. Once you've completed a quarter turn, insert the other bar into a different hole in the cone and let the bar lever against the closed garage door to hold the spring tension. This allows you to move the original bar to repeat the process, alternating the bars with each quarter-turn. It takes about 30 quarter-turns to fully tension a standard torsion spring.
Nate was very courteous and professional and called to let me know that he was about 30 minutes from my house. I had purchased a new Sears garage door opener, but when Nate arrived at my home, he inspected the existing unit and told me that it was still in good shape except for a worn out part. Nate procured the new part and brought it to my home this morning. The unit was repaired in about 10 minutes! The existing unit was just over five years old, so I'm glad I will get some more use out of it.
Our garage door broke 3 days before Christmas, trapping my car inside. We contacted our home warranty, and within 24 hours, Sears called with an appointment time for the next day! I was so impressed! I thought, for sure, with the holidays, we would have to wait. When the technician showed up, he was so friendly. Unfortunately, the repair was not covered under our warranty, but he was able to help us get a good deal on a new spring and still make the repairs that day before he left. He also gave us great advice on how to keep the spring lubricated so it would not break again. I felt like he really went above and beyond to provide great service. Since moving into this new house in August, we have used Sears for several things now, and have been very pleased with the service. It's nice to see that in an age when so many companies just put customer service on the back burner in order to meet their bottom line, Sears still really cares and makes their customers feel important. Thanks for taking care of us this Christmas!

Garage Door Repair And Installation Centennial Colorado 80016


If your garage door is equipped with extension springs (usually seen on single car garages), the cable and pulley might be hanging down when the spring break's. Extension springs use a two pulley system on each side of the door to lift the garage door up and down. When the spring break's everything goes haywire, causing the cables to become twisted or even frayed when they catch on the metal edge of the track. There is a lot of force being released when a garage door spring breaks.
Single panel doors are constructed from one monolithic panel. From the closed position a single panel door swings up and overhead with a hinge on each side (known as jamb type hardware) to the fully open position. A disadvantage of monolithic panel doors is that the swing up arc of the door occurs partially outside the garage. This means a vehicle must stop and park several feet in front of the door to avoid being hit by the garage door when it is opened.

On our EZ-Set Torsion Springs page you will find several options for replacing these springs. We also have step by step instructions for EZ-Set Torsion Spring Replacement. In addition, one of our customers has provided excellent EZ-Set Torsion System instructions for removing the spring without wrecking the winding unit that secures the stationary cone. Instead of a spanner tool, you may prefer to use a pipe wrench or large channel locks to hook the end of the spring and remove it from the cones in the last step. https://www.youtube.com/watch?v=Z_eZc-kh40c&feature=kp
As mentioned in issue #2, garage doors are designed with a reversing mechanism that prevents them from crushing objects in their path. If you find that your garage door closes part way and then goes back up, this can be triggered by objects on the ground blocking their path such as garbage cans or toys. It could also be caused by a buildup of debris on the tracks that prevents the rollers from moving forward. This could include small items like rocks, gum or mud buildup. If the door hits even a small object on the track, it will go back up to avoid crushing whatever is underneath it.

Received all items as indicated, I would recommend purchasing a metal center bearing also, other Than the plastic that this comes with. Install was easy and strait forward. hardest part was finding how many turns to tighten those springs?? I used a general rule of thumb of a full turn for every ft. Of door. 4 quarter turns equals 1 full turn. I found that 26 balanced the door perfectly. These springs seem a little smaller than what was there however, the coil itself is the same. (Pic) After installing, I recommend oiling the springs with some motor oil. This will help with rust and noise. Good luck with yours, it's worth the work for the saving!!
The average cost is $190 for 2 springs in the Detroit area. This is for steel doors weighing under 140 lbs or known as a standard spring which fits 90% of all doors. The remaining 10% are wood doors or large heavy insulated doors. Expect to pay an additional $60 - $100 for a set of these. Garage Door Companies rarely carry these springs on their vehicles or stock them. Therefore, they either buy them locally at a premium or special order them. Regardless, its an additional trip that gets figured into the cost.

Chris was very professional & thorough. He arrived on time & was able to answer all questions that I had. I was extremely satisfied with the quality of the work he performed. I spoke several times on the phone with Mrs. Carol who keep me informed prior to, during, and after the installation of my garage door. She was very professional, easy to talk with and resolved any misunderstanding that I had.


Install new or use this right-wound torsion spring Install new or use this right-wound torsion spring to replace broken sectional garage door torsion springs. All DURA-LIFT springs meet the DASMA standard rating of 10 000 plus door open and close cycles. Both the winding and stationary cones are professionally installed for safe operation. Winding rod is included with ...  More + Product Details Close http://youtube.com/watch?v=Z_eZc-kh40c
Often companies will show different types of springs like oil dipped, galvanized or powder coated and try to convince you that one is longer life than the other and that is why it is going to cost this much instead of that much. Galvanized and Powder coated are great for coastal areas as a rust preventative but do not change the cycle life and do not cost but a few dollars more.
A typical version of an overhead garage door used in the past would have been built as a one-piece panel.[1] The panel was mounted on each side with unequal parallelogram style hinge lifting mechanism. Newer versions of overhead garage doors are now generally built from several panels hinged together that roll along a system of tracks guided by rollers.[1] The weight of the door may be 400 lb (181.4 kg) or more, but is balanced by either a torsion spring system or a pair of extension springs.[2] A remote controlled motorized mechanism for opening garage doors adds convenience, safety, and security.[3]

Garage Door Repair In My Area Centennial Colorado 80015


Torsion springs do not last forever, regardless of what some companies claim. “Lifetime” springs do not exist – all springs have a lifespan. Most builders typically install the lowest costing door available and with that generally comes lower cycle springs. A torsion spring’s life is determined by the number of cycles the spring is rated to last. Whenever the door goes up and down is what is referred to as a “cycle.” The springs that builders install can last as little as 7,500 cycles which means the average homeowner could get 3-5 years of life. http://y2u.be/Z_eZc-kh40c
×